Utilizing ID Cut to Make Custom Stickers Using the CG-AR ~ Tips, Tricks, and Techniques

Рет қаралды 7,468

2 жыл бұрын

Melvin Dothard introduces: Utilizing ID Cut to Make Custom Stickers Using Mimaki CG-130AR Cutter and JV330 printer.
0:40 1. Set Up Print Files
2:11 2. Pre-Flight Artwork
4:14 3. Printing Artwork
4:52 4. Cutting Artwork

Пікірлер: 27

@griaxi4124 Жыл бұрын

This tutorial is amazing and you are really good at teaching !! great job sir !

@MimakiUSASuwanee 3 ай бұрын

We appreciate your support!

@griaxi4124 Жыл бұрын

ITS REALLY WORKED LOL THANK YOU DUDE

@MimakiUSASuwanee 3 ай бұрын

We appreciate your support!

@RReck-ll4wf Жыл бұрын

Hello, this machine looks great. Some New useful features to my CG SRII implemented. How long will the rubberline last (geting repeatable quality) wenn using halfcut like the shown example?

@MimakiUSASuwanee Жыл бұрын

Hello! To increase the lifespan of the rubber lining, adjust the cut pressure to cut through the media only to eliminate significant wear and tear

@ClownfishDepot Жыл бұрын

Very nice video! I am trying to find info on a comparison of cutters between your Mimaki CG-60AR-211 24" Vinyl Cutter and the Roland CG 24? Thanks.

@MimakiUSASuwanee Жыл бұрын

Hello. We have a CG-AR product features playlist: kzfaq.info/sun/PLZtt0QJCo9w5oJbCoVsnZ7LvoKqLZVGHb

@andremolnardesenvolvimento6733 Жыл бұрын

Hello, I saw that right after the cut you detached the sticker, did you use 2 layers of cut line and the half cut function for that?

@MimakiUSASuwanee Жыл бұрын

Hello, you only need 1 cut layer to use half cut. Make sure your cut profile has half cut active when cutting completely through material.

@noxisvibrant 2 жыл бұрын

Hi Mimaki. Can I use the Creasing tool with the new CG-AR size 130 (61”) cutting plotter? Thanks for the reply.

@MimakiUSASuwanee 2 жыл бұрын

@UnrealJoule We do not offer a creasing wheel on our plotters however we do have creasing wheels available for our CF cutters.

@user-nm2ym9zz8l 6 ай бұрын

Hi, We are trying to create a sticker with a kiss cut and perf cut line. Is this doable with the CGar130 and the cutting link plugin? For some reason it is reading both lines as perf cut lines.

@MimakiUSASuwanee 5 ай бұрын

Hello! ID cut can only send over two cut conditions through to the CG-AR from a print and cut machine that has access to the cut edit menu. If you are printing and sending information from any of the 100 series machines or a JV printer then the ID Cut information will only send over one cut condition because the cut edit menu is greyed out and you cannot select two cut conditions to be called out. You can send two cut conditions to the plotter using FineCut9 but it will not utilize the ID Cut barcode doing it through FineCut. Also, if you are wanting to send the two cut conditions over from FineCut9 it will probably be best to create the registration marks with FineCut9 instead of RasterLink7.

@wldbunch Жыл бұрын

Do this works on CJV30 160? With setting do you use to be able to get the sticker to cut out from the substrate? Thanks

@MimakiUSASuwanee Жыл бұрын

Hello, if you are referring to the CJV300-160 then yes! The CJV300 Series has the ability to use ID cut and the Half cut function to cut through many printable medias similar to what you saw in this video.

@user-jb8tv5wu7k Ай бұрын

When i took the print to the plotter and followed all the steps, the machine read the id cut lines fine i hit REMOTE and it began to cut from about 19 inches offset of where the print was located

@MimakiUSASuwanee 23 күн бұрын

Please contact our technical service team at na.service@mimaki.com or at 888-530-3992.

@joanae88 Жыл бұрын

I was wondering if with a CJV150-75 we need a cutting machine or does the plotter already has this full die cut function for stickers? Because all I find is that the printer only half cuts the sheets and we need a solution to make full cuts individual stickers. Thanks!

@MimakiUSASuwanee Жыл бұрын

The CJV150-75 offers HALF CUT which will allow for fully cutting out stickers with small tabs that hold the sticker in place during the cut process. Afterwards, the stickers can be removed with minimal effort.

@rommynine 2 жыл бұрын

What pressure you use on mimaki plotter for die cut? And what is media type?

@MimakiUSASuwanee 2 жыл бұрын

Pressure will depend on how far the blade is out. Please take a look at our CG Series video where we explain how to setup your blade pressure kzfaq.info/get/bejne/d8qFYNmSvKyXmGg.html

@rommynine 2 жыл бұрын

@@MimakiUSASuwanee 😊 thank you

@charoletteduffy6797 Жыл бұрын

can i use these to print clear cast decals

@MimakiUSASuwanee Жыл бұрын

Hello, we would recommend using our UJV100-160 or UCJV300-160 if you want the plotter included. UV ink has an opaque white that will allow for layering on clear decals.