Link to the Game: www.roblox.com/games/11765852... #roblox #bwr #rbwr #powerplant #nuclear
Пікірлер: 54
@norbert099 Жыл бұрын
0:53 Polishers 8:04 Opening valves for Oil (Turbine) 9:11 Preparing for start up 10:15 start up 16:11 Turbine Preparation/Control 20:12 starting Turbine 29:41 Sync. 31:21 A little too much power 32:26 Incident
@alexgaming970 Жыл бұрын
Bro with your video you helped me a bit to the unit 2 start up also nice video
@adonis71282 ай бұрын
thanks you so much i got stuck at the turbines sync part and i saw that u need to switch that little level u deserve this sub and like
@buoyancydabl9 ай бұрын
I love how you were just inspecting deaerator preparing to setup and sudenly power gone lol. I literally lost offsite power today while watching this video with U1 being full. Operating both reactors at the same time isnt easy, but if the U1 coast by the automatic meeting demands nothing bad will happen to it (unless suden power trip)
@jambunboii45376 ай бұрын
with the polishers at the start, you could've just used the greenlit tank to refill polisher 2 and prepped the yellow light tank. im not 100% sure but the tanks and the polishers can function somewhat independently when regenerating polishers
@justasramanauskas-ci7bm11 ай бұрын
Thanks! ❤
@Lesoulevement3705 Жыл бұрын
Oh thanks 🙏
@adamqplaysroblox305 Жыл бұрын
Thanks!
@norbert099 Жыл бұрын
I'm glad I could help
@E_GAMING4043 ай бұрын
Bro pls do U2 start up with guide pls!
@user-cq7zg8cn3s11 ай бұрын
It happen on generator temperator
@Kanru-5829 Жыл бұрын
Apologies as I didn't find any, but was there a reason given on the log as to why the turbine tripped?
@norbert099 Жыл бұрын
Sorry but I was way too focused on finishing my recording as I started to reach around 1 hour and 30 minutes which explains why I didn't look on the log. Isn't there the temperature gauge on the front of the Turbine? The Generator probably exceeded 110℃ which caused the Turbine to trip.
@Kanru-5829 Жыл бұрын
@@norbert099 That would make sense. At 18:02 if you slow it down, you can see the high humidity alert which likely caused the trip.
@user-cq7zg8cn3s11 ай бұрын
This is sliex
@NWIEA2 ай бұрын
I couldn’t complete the startup because the turbine kept tripping from Autocontrol when it hit around 2700 rpm. Not sure why
@guyveg820 күн бұрын
That's probably the cause of Hydraulic Overpressure. You should engage auto RPM and go to TCR for monitoring of the pressure.
@NWIEA20 күн бұрын
@@guyveg8 Yeah, I forgot what is was but I forgot to switch something off
@guyveg820 күн бұрын
@@NWIEA Pump Selectors in TCR. Make sure to turn it off when the Hydraulic Pressure is near the yellow range.
@robbytheatomicengineer57499 ай бұрын
what about the generator cooling with the stupid humidity B.s????
@norbert0999 ай бұрын
I've noticed that people tend to open cold air supply to 100% and warm air to around 50%. However it still isn't really effective.
@norbert0999 ай бұрын
Short-circuits and overheats still happen.
@norbert0999 ай бұрын
But not so often anymore.
@norbert0999 ай бұрын
Go to the Turbine connected to U2, right next to the Turbine is an entrance with a ladder to a small platform. This is where you can configure the cooling for the generator.
@jambunboii45376 ай бұрын
@@norbert099 bit late but you wanna only open cold air enough that generator stays around optimal temps of 75 degrees, and during high humidity you need to supply warm air of at least 2/5 of cold air so people running higher generator loads run 100% cold air and above 40% to maximise generator cooling. If you dont give enough warm air you'll get short circuit and if gen gets too hot itll trip so sometimes all you can do is just lower generator load and wait for lower demand or humidity to go away
@caxap84058 ай бұрын
Guys pls help. How fix condenser open to atmosphere?
@norbert0998 ай бұрын
Disable automatic control. Close the condenser valve but not too much, leave it open a bit and then enable automatic control when there's Steam. Without Steam the automatic control will open the condenser valve too much.
@caxap84058 ай бұрын
@@norbert099 thank you so much
@blueroblox493911 ай бұрын
Evertime i activate APRM the autocontrol just trip the reactor, why does that happen?
@Kanru-582910 ай бұрын
What do you mean by activate APRM?
@blueroblox493910 ай бұрын
@@Kanru-5829 automatic rods control or smth
@Kanru-582910 ай бұрын
@@blueroblox4939 Is there a reason given in the logs? There are logs near the shutdown cooling system panel that tell you why the reactor tripped.
@blueroblox493910 ай бұрын
@@Kanru-5829 it says it got below 4 %
@Kanru-582910 ай бұрын
@@blueroblox4939 What got below 4%?
@kasapz Жыл бұрын
Still cant power it up
@norbert099 Жыл бұрын
Explain why
@kasapz Жыл бұрын
@@norbert099 polishers
@norbert099 Жыл бұрын
What's wrong with the Polishers? I mean I even "showed" RIGHT AT THE BEGINNING of the video how to prepare/operate those. At first it appears hard but it will be easy to understand after some practice. If you want to hear some "actual explanation" of how to use Polishers, pls go to the youtube channel called "RBWR Official". By the way, you aren't forced to use Polishers but if you don't want to use them, you might get less points?? I don't know... I can only roughly remember what the guy from RBWR Official said.
@kasapz Жыл бұрын
@@norbert099ik but when u press the water button it blinks but when i do everything exactly as in the video and press the water button nothing happens and it does not blink
@kasapz Жыл бұрын
And also,when do u change the srm to ipr and change the ipr 1 to 2 u sped it up so i cant see it