V8 Swap Toyota FIRST START!!! - 1UZ 1989 Pickup
Рет қаралды 28,652
3 жыл бұрынFINALLY the 1UZ V8 Swap is running in my 1989 Toyota Pickup! This episdoe we put another 1UZ in the truck, swap harness's a couple times, and then wire it up! Ending in glory, she roars to life.
Support Dirt Garage by purchasing our Merch! - www.dirtgarage.ca
Brought to you by @ Overland Outfitters - overlandoutfitters.ca/
INSTAGRAM - / dirt_garage
Get 10% OFF Afraid Knot Ropes with my discount code "dirtgarage"
www.afraidknotropes.ca/
My 2020 OFFROAD Gear Kit / Recommendations: USA Affiliate Links
Lunchbox Locker: amzn.to/34lDTfI
Smittybilt Compressor: amzn.to/2vhwEqm
Tire Deflator Tool: amzn.to/2SwmbPO
Smittybilt Winch: amzn.to/2HbKP2Y
Recovery Rope: amzn.to/39om3Ze
Soft Shackle: amzn.to/3bnRg0t
Hard Shackle: amzn.to/39ouyDA
Recovery Hitch: hamzn.to/2SeE6LN
CANADIAN Amazon Affiliate Links:
Smittybilt Compressor: amzn.to/35DcvY3
Tire Deflator Tool: amzn.to/2QBWPQA
Smittybilt Winch: amzn.to/35CBOJO
Recovery Rope: amzn.to/2s9qRlj
Soft Shackle: amzn.to/2R4j5Bx
Hard Shackle: amzn.to/39QXpl3
Recovery Hitch: amzn.to/306WyIL
Music Licensed @ Artlist
Find music for your videos on Artlist! artlist.io/Clinton-279876
My 1989 Toyota Pickup Build: • My DREAM Toyota Build!...
- 5VZ-FE 3.4 Swapped
- Manual Swap
- Dual Transfer Cases
- TRD Supercharger
- Solid Axle Swap / SAS
- OME Rear Springs & Tundra shackles
- 37x12.5r17 Toyo MT Tires
- Build Playlist Here: • V8 Swap Toyota Pickup ...
Camera Gear Used To Make This Video:
- Camera: amzn.to/36C4dkI
- Microphone: amzn.to/2QDkIaB
- Tripod: amzn.to/2sdCkR0
- Gimble: amzn.to/2FyndVf
Business contact: Dirt.Garage@outlook.com
@definitelynotpewdiepie 3 жыл бұрын
Dude, this truck is gonna be an absolute BEAST. Props to you for your persistence on this project. A lot of guys would have quit, but you've stayed on it and made a ton of progress. I hope the next video is you doing burnouts and doughnuts!
@TheStoryTillNow 3 жыл бұрын
Soooooo happy this thing runs 😂
@DirtGarage 3 жыл бұрын
Me too!
@philgriswold2133 3 жыл бұрын
I'm old enough to remember the big problems were motor mounts, bell housing and making the headers fit. All of these wiring harnesses are an entire different science. Great job. It should be a beast on the street and trails.
@gyffjogofl7676 3 жыл бұрын
Its all the little stuff that keeps people from completing a swap. Glad you show it.
@DirtGarage 3 жыл бұрын
Huge list of little stuff, especially with the fire resto part. Nice part is everything on the truck side is going smoothly, just the engines I had trouble with...
@NuttyNu 3 жыл бұрын
Please make a overview review of the swap once you’re finish.
@TavaresAndres4x4 3 жыл бұрын
Nice swap bro, kind regards from Brazil!
@peterwatson8295 3 жыл бұрын
Hell yeah congrats! Your never give up attitude is very inspiring. I'm about to go try to get my 22r to 22re swap to run so this video was great motivation!!
@kyledurrett8134 3 жыл бұрын
Righteous Dude, the beast is alive and sounds awesome! Sound tracks on point as usual too 🔥🔥🔥
@DirtGarage 3 жыл бұрын
Glad you like it!
@simonpope1780 3 жыл бұрын
Hell yeah it’s a good day dirt garage is back
@philrab 3 жыл бұрын
Your commitment to seeing through a project is inspirational my man.
@mountainjeepmike4408 3 жыл бұрын
So good to hear it running man!!!
@seancheetham7454 2 жыл бұрын
You have the patience of a saint. Would be great to have a final video that shows all the things you learned and what you would do differently if you were starting this again.
@UnwindingRoads 3 жыл бұрын
Music to our ears! Awesome Clint!
@DirtGarage 3 жыл бұрын
Thanks!
@franksbigday5468 3 жыл бұрын
The look on your face when it ran for the first time. I smiled so big. I know that feeling. It's a good feeling.
@DirtGarage 3 жыл бұрын
Man, was I ever happy. Still smiling!
@bentenxl 3 жыл бұрын
love this, you have quality! hope your channel blows up
@DirtGarage 3 жыл бұрын
Thank you so much!!
@TheGreatPursuit 3 жыл бұрын
Man that is just awesome I am really happy for you Clint!
@heavyprogressive76 3 жыл бұрын
WHOOOO!! right on buddy what trip! Way to keep on er I love your persistence my friend!
@DirtGarage 3 жыл бұрын
Thanks! Will do!
@kimofarias7773 3 жыл бұрын
Love how the truck shifts a little when you rev it. Great content keep it up👍🏾
@DirtGarage 3 жыл бұрын
Yeah, this actually surprised me a bit!
@toninodemitri3345 3 жыл бұрын
Congrats man! Persistence pays off keep em coming🤘🏼
@DirtGarage 3 жыл бұрын
Sure does!
@RM_Garage 3 жыл бұрын
Can't wait to see this thing on the trail. Awesome job buddy!
@DirtGarage 3 жыл бұрын
Thanks 👍
@matthieucorbeilwalsh 3 жыл бұрын
So glad to finally see things going your way with this swap. I've been having issues too on my '90 4Runner lately but it will get back on its wheels. “It is the time you have wasted for your truck that makes your truck so important.” Saint-Exupéry would say
@DirtGarage 3 жыл бұрын
Thank you! I don't see it as wasted time. I do like working on it, just a little less than I have been over the past 5 months would be nice!
@Rogueflier 3 жыл бұрын
I cried a little.... Great vid, Dope soundtrack. Appreciate y’all👊
@DirtGarage 3 жыл бұрын
Thank you! I nearly did too, so much work, finally paying off.
@willisgoodger1875 3 жыл бұрын
Hot dam! Fire in the hole! Sounds awesome! So glad you got her running. You got me anxious like back in my younger days.
@DirtGarage 3 жыл бұрын
Woo, yeah I'm so happy to have it running again.
@jvogler_art4708 2 жыл бұрын
I wish there was more footage of it actually driving.
@mokreepinjeepin8100 3 жыл бұрын
NICE!! Engine bay looking NEW! Wiring wud turn my brain to mush.. 😆 Congrats on getting wrapped up Clint, miss that off-road content hope it screams.
@DirtGarage 3 жыл бұрын
Yeah it's soo nice and new! lot of work! My brain has been mush for months straight over all this, wiring is actually the easy part for me.
@bob_frazier 3 жыл бұрын
What could have been a 5 part video series Clinton knocks out in 1 short vid. Super happy you had some success!
@wernerboeinck9467 3 жыл бұрын
Congrats and better luck this time!!!
@sprk11 3 жыл бұрын
looks good, and sounds awesome. Can't wait to see out in the trails.
@DirtGarage 3 жыл бұрын
You and me both!
@wetcoastwheelin 3 жыл бұрын
Congratulations on getting the motor running
@michaelcook184 3 жыл бұрын
Good job way to hang in there on this project
@jakeofallterrains9048 3 жыл бұрын
It really does look at home inside that engine bay.
@carlosarroyo5262 3 жыл бұрын
Epic. Love the fact that it's all Yoda.
@DirtGarage 3 жыл бұрын
Thanks! Me too!
@philfoote829 3 жыл бұрын
Had to watch it again so good
@HomebrewSubaru 3 жыл бұрын
That's a pretty cool project. Just found your channel. I'm in BC as well
@caveman9275 Жыл бұрын
Always amazing 🤙
@lilrip7532 3 жыл бұрын
Ballenger Motorsports has wire harness plugs & pins. Great prices , fast shipping and located in Virginia.
@jason.k30chevy31 3 жыл бұрын
Congrats! Awesome man!
@DirtGarage 3 жыл бұрын
Thanks!!
@Taylor-gm8je 3 жыл бұрын
Hi! i'm looking into doing this swap on a first gen 4runner could you show us some insight on the wiring part of things and show us what you needed to do to get it to run?
@DirtGarage 3 жыл бұрын
Once I get it all buttoned up I will!
@glenhayhoe 3 жыл бұрын
Great Choice of music... I thought this truck was toast (pun intended) after the fire.
@bowababowaba7471 3 жыл бұрын
So sick!!
@BruceCookfmx 3 жыл бұрын
Yeah buddy!
@lucasgiannetti8748 3 жыл бұрын
amazing work man!
@DirtGarage 3 жыл бұрын
Thanks a lot!
@southernmudder2 3 жыл бұрын
So glad you got it all figured out
@DirtGarage 3 жыл бұрын
Me too!
@shervang1700 3 жыл бұрын
Awesome !!! That yota gonna be a beast !!!
@DirtGarage 3 жыл бұрын
Absolutely!
@coop_69 3 жыл бұрын
I really need help with my 3vze rebuild it started and ran so I put on the radiator fan and shroud and the little stuff but when I tried to start it then it just cranked I don't think it's getting spark but I have no clue and it's been sitting for way too long
@judgordo 2 жыл бұрын
Hi great job, I am from Mexico have a question waht type of ECU used i made the same swap in my tacoma but only running after 10 seconds shut of can you help ?
@levsheppard2859 3 жыл бұрын
it lives!
@herbbuckland9223 Жыл бұрын
While I appreciate providing an insight into the task you assigned yourself for those of us who might think to do a similar conversion, I am of an age where the music you chose as a background filler gave me a headache. To each their own though. Despite the differences in music between your age and my 50s-60s age group, a definite level of camaraderie can be shared since many of those in my generation routinely did engine (etc.) swaps... minus the headaches today's vehicles give due to the electronic-based systems. Nonetheless, I would like to point out that there are no doubt several people who come across this project of yours and had hoped to see a start- to- finish conversion where a V-6 was replaced with a V-8. Thanks for sharing your adventure.
@triedandtrue1820 3 жыл бұрын
Is there a engine vin code that has difference from LS to SC identified? JDM usually sell as a LS/SC 400 , cheers good job.
@judgordo 3 жыл бұрын
Nice job, what type transmission use?
@stew2049 3 жыл бұрын
Dude this is so awesome. Gearing up to do a 1uz swap in my 92 pickup right now. So pumped. Just curious what ballpark budget you were looking at to get adapter plates mounts and wiring completed on your swap ?
@DirtGarage 3 жыл бұрын
A lot! Lots of little stuff that adds up. Probably $3000-$4000ish at end of day. CAD
@cmac956 3 жыл бұрын
Hay ,good job , a lot of work .you did well. have fun with it.
@DirtGarage 3 жыл бұрын
Thank you, I will
@longobardir 3 жыл бұрын
Love it! Makes me lean more toward the 1uz for my 1990 4runner. Local wrecking yard has a 5vz-fe, 1uz, 2uz, and a 2jz. I was leaning towards the 2jz but after hearing that v8 roar I might reconsider. Congrats!
@DirtGarage 3 жыл бұрын
I recommend 5VZ, very easy straight forward! East with minimal experience!
@longobardir 3 жыл бұрын
@@DirtGarage oh, I'm a mad scientist tho. My 2007 Sv650 is a Frankenstein, Removed the fuel injection and swapped in carbs. Had to make a custom half and half harness. I was mostly leaning towards the 2iz since im tired of the complexity of the v6 over the inline. (Buried knock sensors, no access to things like starter, etc.)
@jasonh4167 3 жыл бұрын
Awesome man..! Bet your feeling good😊.
@DirtGarage 3 жыл бұрын
Very!
@MattSanipass81 3 жыл бұрын
Coming along great now bud… Happy for yah…
@DirtGarage 3 жыл бұрын
Thanks 👍
@FlawedOffroad 3 жыл бұрын
I admire the persistance, as Im stuck in the awful stage in my build where im overwhelmed with the little crap that keeps turning into big crap. get er done!
@DirtGarage 3 жыл бұрын
I know the feeling. My list of stuff to do was HUGE after the fire.
@pocoapocooffroad 3 жыл бұрын
7:38 try feeding 12v with a switch to the main relays and you should be good. Race car style
@timeforbigchange9417 Жыл бұрын
Plus you lowered the center of Gravity when lowering the engine.
@camwoodsend2097 3 жыл бұрын
Way to stick with it. You’ve overcome some huge obstacles!
@DirtGarage 3 жыл бұрын
Thank you! Some pretty good obstacles, that is for sure!
@jacobhendrickson8935 3 жыл бұрын
Wow do you work a full time job while doing all of this?? When do you sleep if so? Lol back in the day I had that kind of energy but it’s long gone now. I’ve been to lazy to do a tune up on mine. Oh and adjust valves and change valve cover gasket as well. I love my 22RE.
@Thexkidd 3 жыл бұрын
Woohoo 🙌. Sounds great.
@DirtGarage 3 жыл бұрын
It does!
@frankstall1347 3 жыл бұрын
Sounds Sweet !
@DirtGarage 3 жыл бұрын
Right?
@frankstall1347 2 жыл бұрын
@@DirtGarage I want a 1UZ to put into one of my 2nd Gen 4runners with the 5 speed.
@daviddaniels6645 3 жыл бұрын
Love it!
@j-tag4913 2 жыл бұрын
So much hard work hopefully not bankrupting you to do this.
@wetbeaver925 3 жыл бұрын
Hell yeah buddy
@jmudd5449 3 жыл бұрын
Did you use the SC oil pan?
@DirtGarage 3 жыл бұрын
Yes, I did swap the pans over.
@goatsgarage2252 3 жыл бұрын
How hard is it to wire in a carb toyota?
@homegrowncustomsandautorep9737 3 жыл бұрын
Sweet!
@greganderson2874 Жыл бұрын
Does the 93 pick up bell housing match to any American mfg ?
@cnc75adventures49 3 жыл бұрын
Yeah👍👍
@Red_Beard_Builds 3 жыл бұрын
So bad assss!
@slightlypermafried 3 жыл бұрын
Are you still running a manual gear box, if so what did you do to fit the bell housing? I have a donor sc400 and a 89 pickup staying 2wd
@patrickfields3392 3 жыл бұрын
He said he bought a bell housing adapter to his transmission, I believe they sell a uz to w55 series trans
@patrickfields3392 3 жыл бұрын
An adapter that is
@slightlypermafried 3 жыл бұрын
@@patrickfields3392 I think he started with a 5vz and r151 trans and stayed with that. I’m scared to try my stock w56, it’s not made for much
@fortunesk89 3 жыл бұрын
I need one in my Toyota dolphin! This is hooked to a manual transmission right?
@DirtGarage 3 жыл бұрын
Yup! R150
@dieselmack2548 3 жыл бұрын
No fire extinguisher in camera view, no friend on standby watching engine, first start inside your shop. So much for living and learning. 😂 some people going to call this a troll.
@DirtGarage 3 жыл бұрын
Just because it's not visible on camera does not mean it's not there. And 100% learned. Fuel system was pressurized before I even tried starting it. And checked a hundred times for leaks in fuel system.
@nemesis851_ 3 жыл бұрын
Before i see the whole video, I think there will be no less than 3 people with Fire-Extingishers on hand, at key turn crank
@DirtGarage 3 жыл бұрын
Nope just me. Being very careful looking for fuel leaks after every step. Not shows on camera haha. But I pressurized the fuel system before hand looking.
@joshlosesweight6140 Жыл бұрын
Did you need an adapter plate for the transmission
@DirtGarage Жыл бұрын
Just had to get a 1UZ to R150 bellhousing
@deadjoey77 3 жыл бұрын
fuck yeah. I have a 1uz and an 85 pickup in my driveway right now. about to send my harness in to have work done, dropping engine in while i wait. then ill need to buy driveshafts, flywheel, clutch, bellhousing. plop that with the trans, hook the wires up and hope it works. what hickups did you run into? i know our platforms are slightly different but any info would be awesome!
@DirtGarage 3 жыл бұрын
Pretty much everything worked out great. My bellhousing and clutch kit from KSRacing bolted up perfectly! And clutch seems to work great. I ended up using 2UZ headers, they are tighter than the 1UZ ones.
@nemesis851_ 3 жыл бұрын
WHoooooooop - - - Whoooop !!!!
@86er01 3 жыл бұрын
good job ,,,,,,
@projekt6_official 3 жыл бұрын
Woohoo!
@doughboy1966 3 жыл бұрын
Did you have to do a body lift?
@DirtGarage 3 жыл бұрын
Yeah 2"
@zekealvarez4108 3 жыл бұрын
what trans did you use for this swap?
@DirtGarage 3 жыл бұрын
R150
@IamEmmett 3 жыл бұрын
sounds mean!
@kingofthe6spd 3 жыл бұрын
you need a de-pin tool. could have been much easier on you! but congrats on the running truck!
@DirtGarage 3 жыл бұрын
Yeah it would make life alot easier!
@emacdaqt350 3 жыл бұрын
Wow
@mikediamond257 3 жыл бұрын
Note to self........ NEVER do a v8 swap in mine 😂
@noneyabizz8056 3 жыл бұрын
nice no fire!
@DirtGarage 3 жыл бұрын
Oh yeah!
@goatsgarage2252 3 жыл бұрын
I got a 93 lexus wid 4.0 for free ...its debadged..how do I kno wat motor I have if it's an interference engine or not ?
@DirtGarage 3 жыл бұрын
93 is non interference. They switched in 95
@goatsgarage2252 3 жыл бұрын
@@DirtGarage awesome thank u so much love the channel love the swap u inspire me !!! Thank you!!!
@stevew9247 3 жыл бұрын
The harness on those engine is really snaked in and out of everything
@DirtGarage 3 жыл бұрын
They really do!
@BassSniper209 3 жыл бұрын
do you think you csn collaborate with fabrat
@DirtGarage 3 жыл бұрын
That would be sweet!
@vzt5789 2 жыл бұрын
What transmission is running??
@DirtGarage 2 жыл бұрын
R150
@vzt5789 2 жыл бұрын
@@DirtGarage any other transmission can do? Cuz my area don’t have R150
@jacobhendrickson8935 3 жыл бұрын
Wouldn’t you want the engine to sit as low as possible anyway??
@nemesis851_ 3 жыл бұрын
I shudder, with feelings of Deja-Vu (wiring)
@austinsears2299 3 жыл бұрын
Not trying to call you out but didn’t you say no more first starts in the shop? 😂
@DirtGarage 3 жыл бұрын
I was very very carful. Checked for fuel leaks about 100 times!
@gunnerwagoner255 2 жыл бұрын
I’m sorry I see now you ditched the 2uz for some reason
@DirtGarage 2 жыл бұрын
Did you miss the while fire thing?
@bob_frazier 3 жыл бұрын
Computer issues? Make a 22r sound better all the time.
@gunnerwagoner255 2 жыл бұрын
I’m sorry but why are you calling it a 1uz now ??
@DirtGarage 2 жыл бұрын
Because it is a 1UZ. The 2UZ caught on fire and burnt up the truck. The 1UZ was its replacement.
@dronetrucker 3 жыл бұрын
I want to 1uz my fj60
@DirtGarage 3 жыл бұрын
That would be rad, those need more power!
TravisTutorial
Рет қаралды 89 М.
Юра и Вика
Рет қаралды 4,8 МЛН
Я тебя застрелю🤬 #эндуро #эндурокросс #мотоцикл #мото #кросс #прохват #moto #motocycle #enduro #cros
Денис Сумкин Enduro
Рет қаралды 14 МЛН