Hi, great job. I do similar stuff for rc cars, my advice is less sagging of the material and more pulling / stretching of the material by the vacuum. Mostly sagging is only 1/3 of the model height.

Heat the mold first! You should make a cavity on the bottom .(guessing) but cut out a 3"x 5" hole in the center of the wood that is attached to your mold. Then drill your fine tune holes to that cavity . That will give you extra pulling power plus heating the mold first helps a bunch because when you drop the sagging plastic on a cold mold it cools it to fast trapping unwanted air. Hope this helps you!

Ayy hasta da coraje ver como meta la pata este muchacho, y para colmo parece estár feliz con sus resultados, ni hablar.

Stick around! The ending design and Test results are MUCH MUCH BETTER! I Like it!!

Thank you for sharing ! Merci monsieur. I may thy some days . J'' essayerais bien un jour mais pas sûr et pas évidant .

Nice n clean build

Buenas, por donde es mejor calentarlo? Poniéndola resistencia abajo o calentarlo por arriba, gracias muy buen trabajo

Ótimo grande projeto!...

Great information

fantastico bro

Nice job!!

🎉🎉 parabéns. Man como vc faz esse moldes tem algum vídeo ai??

Really cool work , Let me paint the van XD

Can you help me please I want to mold with acrylic pmma 2 mm thikness .. wath kind of motor should i use ??

I love your setup, I’m taking ideas that people have and just seeing trial and error. Any notes you’d change after using it for a while?

Where’s the little holes you have to have in the mold? They go in inconspicuous spots and it gives you a deeper pull

Bravo!

Nice final product !! How do you create the positive form ? cheers

Is 10 mil ( .25mm ) polyester film okay for forming and will a 3D print of PLA work for the form?

Where can you buy those acrylic sheets (PMMA)? , or plexiglass in the market? that are thermoformable. Is there a link or website to buy online? Thank you very much for the help, best regards

Hello,may i ask the vacuum pressure is?

ahojte , také jsem něco zkoušel a zatim sem se nepřiblížil ani trochu k jednom z vašich testů , takze vysledky mam 00nic , mohly by ste mě poradit co můžu dělat blbě , popřípadě kde by sme to probraly ? fb ? mail ? děkuji vám moc

Tem algum video ensinando fazer o molde?

What are the dimensions of this unit? What is the material you are using at 1:56 to form the heater box? I am guessing it is some sort of ceramic. Did you find that there were any leaks when you use wood in the vacuum box?

Do you make your patterns out of plaster? Do they leave a perfectly smooth surface on clear plastic? Thanks

Nice! What material you use for mold?

That test #3 with the cowl mould was never going to work with it’s deep vertical sides.

What is that name of plastic

Cool video what's the name of the music you used

good job!!!

Does clear PETG turn white when over heated?

De onde vem os moldes?

Qual matéria ficou melhor

predavas body ? ak ano mas aj 1:10 ?

Do you sell it?

what is the mold made of

what is your source of heat? what are you heating up with?

22b?

Tamiya XV01 Rally!!!

haces bodys paRa vender?

Vacuum forming a giant phallice stone. Hahahaha

Can I find out where lexan comes from? purchase address etc. thanks regards

Язык ваш прикольно звучит))

How to build vacum?

Dobrý den, prosím o kontakt na Vás. Potřebuji poradit s realizací podobného zařízení pro prototypy respirátorů. Díky milan.knobloch@seznam.cz

tabugok!

It would be better in English 😆

Zlatý český ručičky...