No video
Vacuum Table 24x24
Рет қаралды 25,532
Күн бұрынTed Gauthier shows his portable vacuum table hold down system used on the CNC.
@jeremymartinez8901 5 жыл бұрын
Throw some paper or cardboard on top next to the smaller material. It will plug the vacuum surface area enough to hold it steady. I work at a plastic fabrication warehouse. I could send you some really thin polycarbonate or abs to use as cover sheets. The guy that runs the router here has a bunch of them cut to different sizes to cover the table depending on the size of his material, and that cnc is a monster. 6x12ft cutting area up to 4”
@FlyBalloons1 5 жыл бұрын
I did that Jeremy but a shop vac doesn't have enough suction. I bought a dedicated vacuum pump that should work with your suggestion but I have not had time to hook it up yet.
@misterjj779 2 жыл бұрын
Very nice. Thank you for that. I especially like the idea with the added spoil board so you can cut all the way through.
@thisoldman7142 7 ай бұрын
Thanks for the video Ted. I’m hoping to do the same size vac table for my CNC with one difference. I’ve just ordered an oil free vacuum pump from Amazon. Fingers crossed. 🤞
@scottprints 2 жыл бұрын
Great video, thanks for posting! I hope to make something similar for my own CNC someday.
@djameldeneche3020 Жыл бұрын
Thanks a lot sir !!!!
@doglao1236 3 жыл бұрын
nice job
@martinquirion6783 3 жыл бұрын
Nice, tank you sir for the vidéo 👍
@carloavergas 5 жыл бұрын
Great video Ted. Do you think that 3/4" PVC sheets would be a good substitute for the melamine? Thanks for making this video!
@FlyBalloons1 5 жыл бұрын
Carlo Avergas .....thanks Carlo.
@FlyBalloons1 5 жыл бұрын
Not sure if Pvc is porous. You would need to look up the specs or test to see if air travels through it. You don't want air moving through your vacuum table base.
@bitsurfer0101 Жыл бұрын
If you had a cutout sized according to the smaller piece, could you get more suction?
@customwalldisplay 10 ай бұрын
I’m in the middle of making one and have 6 hp shop vac I plan to cut acrylic parts my file is 7 mins long will this burn my shop vac motor up? The vacuum table size is 22x25”. Thanks
@dronesvisionsaeriennes 4 жыл бұрын
Good Job Ted, what is the depth of the line for perimeter and inner seal , and size of each square please...Thank's a lot Philippe
@johnlyons4750 4 жыл бұрын
What is the gasket material? what size is the gasket material? Where did you purchase it? You said the dado for the gasket material was 1/4" deep, but how wide?
@tabsquare 5 жыл бұрын
Nice work! I maybe lost it, how much is your vacuum wattage? I am planning to do a similar format vacuum table and was wondering if a 700W, 24kPa vacuum would do the trick.
@FlyBalloons1 5 жыл бұрын
I just used a shop vac.
@1bulldog998 5 жыл бұрын
nice video i was looking for something simple that works well enuff for me i.ll try to make this ... ? couldnt u use a 1/4 ' MDF INSTEAD OF SHAVING IT OFF
@FlyBalloons1 5 жыл бұрын
Good luck with you table.
@FlyBalloons1 5 жыл бұрын
Yes you could use 1/4" but shaving off the mdf will make your board more pourous and the vacuum will have a greater pull.
@1bulldog998 5 жыл бұрын
@@FlyBalloons1 oky will do great add vice
@atmm89 2 жыл бұрын
could you use this system on EVA foam?
@bitsurfer0101 Жыл бұрын
What does acrossed mean?
@Stephen8454 5 жыл бұрын
What pump would you suggest for just a 2x2 table like this? I'm planning on making one myself
@FlyBalloons1 5 жыл бұрын
I used a regular shop vac in that demo. Worked fine.
@Stephen8454 5 жыл бұрын
@@FlyBalloons1 Yeah I got that i was just curious if I made a 24 x 24 to run for hours would I need to over think what kind of CFM or just get the cheapest dual motor air pump on amazon lol :D
@FlyBalloons1 5 жыл бұрын
@@Stephen8454 if you were going to run it for hours then yes you would. I use a Festool but a Fien vac would work. Hope that helps.
@shelby50411 5 жыл бұрын
What the hell?....the vacuum goes throught the mdf and hols the part?...what am i missing?...is that magic..?
@No1sonuk 5 жыл бұрын
Yeah. That's what I thought too. Maybe the MDF is more porous than it seems?
@jeremymartinez8901 5 жыл бұрын
Mdf is super porous. The air passes right through. I’m pretty sure there’s a soft grade you can get that has better airflow. Not sure what we order, but he usually surface planes it down every so often until it’s about 1/2” and then scraps it and uses a new one.
@FlyBalloons1 5 жыл бұрын
der ddd McFadden is porous so air will travel throughout. It is even better if you skim each side to remove the top and bottom layers.
@FlyBalloons1 5 жыл бұрын
Mdf is porous
@TheLaserguy2 5 жыл бұрын
Hi Ted. Good information. Passing on a hint. On another video, for your small parts, Peters video describes a very good solution. newspaper. kzfaq.info/get/bejne/m7anfc1mrbOckp8.html
Dan Connell Designs
Рет қаралды 16 М.