Valve adjustment on a Volvo D13

Рет қаралды 42,620

Pauls truck repair

5 жыл бұрын

Thanks for watching! please like and subscribe!

Пікірлер: 43

@TATEXPRESSINC 4 жыл бұрын

Awesome Video!🎥

@PlayerzAnthem 5 жыл бұрын

nice video man I just hate seeing people using a 700$ torque wrench to break stuff free

@Rudysgaragellc 2 жыл бұрын

It’s not your tool so why do u care ?

@mechmobile2019 Жыл бұрын

If it's advertised of meting capable 100% possible it could be safe for the tool

@moisesautoandtruckgarage6024 3 жыл бұрын

Keep on blogging sir and sharing your knowledge. This is my support from #MoisesAutoAndTrucksGarage

@isaaccharles4051 4 жыл бұрын

Great video brother I am new to your channel already subbed learning a lot about these Volvo engines thanks for the video God bless

@cliffordcolemon4279 2 жыл бұрын

Thanks I needed lat more God blessings

@johnysilver1853 2 жыл бұрын

Did you adjust engine brake as well what minute on the video?

@Gumigeling00 4 жыл бұрын

While this might be "ok", it is not correct way to do the overhead adjustment on Volvo engines. When you finish, engine should have made 2 revolutions. So do Intake and Injector, then turn engine and do exhaust and engine brake, then turn again to do intake-injector and so on. Also, make sure cam mark is between two lines (not close to 1st or second but between them).

@paulstruckrepair6016 4 жыл бұрын

Arnes Kadic have you ever set timing on a d13? If you have you would know the mark has to be closer to the first mark for the most accurate adjustment

@Gumigeling00 4 жыл бұрын

@@paulstruckrepair6016 have you ever done it? Did you get newes buletin on setting timing? If you did, you would know that it has to be in middle.

@Gumigeling00 4 жыл бұрын

@@paulstruckrepair6016 check Operation 2140-05-03-01 dated 08/12/19

@paulstruckrepair6016 4 жыл бұрын

Arnes Kadic buddy iv don’t this a 1,000 times your not teaching me anything I don’t know 👍

@Gumigeling00 4 жыл бұрын

@@paulstruckrepair6016 I understand, and maybe you have done it 100000 times, I am saying way you are doing it is not the way Volvo does it, or recommends doing it.

@e7sasrayg 3 жыл бұрын

Where did you get these sizes?

@mechmobile2019 Жыл бұрын

Good job . How to decide when to use a shim and when to adjust the nut and bolt to tighten the shimm?

@taiviet20 4 жыл бұрын

you dont adjust the engine brake?

@berenicerobles4654 3 жыл бұрын

Hello, excellent video that the adjustment sheets have administration, injector and brake in Spanish please

@juanvelasco1971 Жыл бұрын

Do you help with valve adjustment?

@armandodomingo9468 Жыл бұрын

Hi, How about the exhaust brake?

@rudyalvarez8339 2 жыл бұрын

Where are you located I need some work done on my volvo

@alexandertakele6136 3 жыл бұрын

Hi boss, i got a question I have a 2013 Volvo with d13 820k now def deleted still has egr I replaced injectors a year ago . Ever since I replaced the injectors I get a lot of fuel smoke blueish whiteish only at first start up and if I shut it off for 20 min and turn it back on. After warmed up I can’t see the smoke but can smell it. Do you know what it could be ? I can’t get a mechanic to figure out what it is

@emlkl1779 Жыл бұрын

Exhaust valve isn't adjusted properly .hence the smoke

@elioavila99 6 ай бұрын

Alexander , I have the same problem with my Volvo . Blueish smoke at startup and misfiring then after 5 minutes goes away . Did you ever find the cause for this issue ? Asking for my self I want to know . One mechanic told Me is just the injector and once the injector gets warm it stops . He said I don’t need to worry about it

@user-qg1xg8eu2r 3 жыл бұрын

كم رقم الشفره اللي تستخدم لعيار البلوف

@antoniobermudez4989 2 жыл бұрын

Hey friend. Where can I buy the adjustments shim kit. That is not in Volvo dealer

@paulstruckrepair6016 2 жыл бұрын

Volvo sells the shims individually not as a kit

@taiviet20 4 жыл бұрын

Did you turn engine by alternator?

@paulstruckrepair6016 4 жыл бұрын

Tai Tran yessir

@e7sasrayg 3 жыл бұрын

You could get the same tray that's in the video

@paulstruckrepair6016 3 жыл бұрын

Volvo dealer or Mack dealer

@samankirkuk9461 4 жыл бұрын

What is the measurement in mm in and out?

@paulstruckrepair6016 4 жыл бұрын

saman kirkuk exhaust 991mm. 203mm intake

@samankirkuk9461 4 жыл бұрын

I mean Phils Rev up

@mohammadrabbani4113 3 жыл бұрын

Hello sir give valve adjustment matohd and injector adjustments i want pdf files please

@gerardquinn2572 3 жыл бұрын

Where do you get the boxes of shims ..

@paulstruckrepair6016 3 жыл бұрын

Mack dealer or Volvo dealer they don’t sell the whole box you have to buy them individually

@arthurvilla8636 10 ай бұрын

@@paulstruckrepair6016I’m currently doing a overhaul on a Volvo d13 same engine anyways and I can’t bar the engine over by the alternator I was able to but once I kept adjusting the valves it got hard af to turn to the point where I can’t anymore.

@coachafrane3521 5 жыл бұрын

What sizes of filla gauge do you need

@paulstruckrepair6016 5 жыл бұрын

8 thousands for the intake valve ,39 thousands for the exhaust valve, and for flats for the injector,

@Silvervwolfee 4 жыл бұрын

What does that mean "for flats for injector"

@SalvadorBtc 4 жыл бұрын

@@Silvervwolfee the nut has six flats or sides. So you turn it 4 flats...I hope I explained it well

@quientonsmith1395 Жыл бұрын

Awesome work basically open heart surgery. If you own the truck you have to rely on the mechanic really giving a s($& because he could essentially just pop the valve cover and put it back on for the labor