Van build | Trim

No video

Van build | Trim | How To

Рет қаралды 23,438

Күн бұрын

In this van build episode, we will be showing the easiest way to trim out the areas above the sliding door and back doors. As always we will be discussing tips, tricks, mistakes & cost.
We are Ben and Jelaine with Nomadic Visuals. We are currently converting our Ram Promaster into our tiny home on wheels. Follow along with us in our van build series.
/ nomadicvisuals
Closed Cell Foam - amzn.to/3CXQmGs
Duramax Fabric - www.nationalup...
Other Van Build Content
Sound deadening - • Van Build Sound Deaden...
Window install - • Van Build Window Insta...
Subfloor - • Van Build Subfloor Ins...
Insulation - • Van Build Insulation -...
Framing/Furring - • Van Build Furring/Fram...
MaxxAir Fan Install - • MAXXAIR FAN INSTALL| H...
Propane Tank - • Van Build Propane Tank...
Hot Water Heater - • Van Build | Tankless P...
Heated Floors & Vinyl Plank Flooring - • Van Build | Heated Flo...
DC Electrical Rough-In - • Van Build | DC Electri...
Propex Propane Heater Install - • Van Build | Propex HS ...
DIY Ceiling - • Best Camper Van DIY Ce...
Swivel Seat - • Promaster Swivel Seat ...
Upper Cabinets - • How To Build And Insta...
Kitchen Cabinet - • Building Kitchen Cabin...
Bathroom - • Van Build | Start to F...
Propane Remote Fill - • Van Build | Nashfuel P...
Butcher Block Countertop - • How To Cut And Finnish...
Solar Roof Rack - • Van Build| DIY Solar R...
Battery to Battery Charger - • Video
Bed and Table - • Van Build | The Best B...
Fresh Water System - • Van Build | Fresh Wate...
Finishing Out Doors - • How to finish out your...
Follow us on Instagram:
@Nomadic_Visuals_
Ben's Photography
@ben_gilliland_
Disclaimer: Some of these links are affiliate links where we'll earn a small commission if you make a purchase at no additional cost to you. This is how we are able to grow our channel and keep making videos.
#vanbuild, #vanlife, #promaster

Пікірлер: 25

@PotatoesAreNeat Ай бұрын

This video has been so incredibly helpful, so thorough. I especially loved that you cut access holes in the back for the lights. I see too many conversions covering up essential areas!

@WexWorld 3 ай бұрын

Super glad I found this video! The closed cell rubber appears to be the solution I was looking for!!

@jrewillis 4 ай бұрын

4 way stretch carpet would remove the need for the foam underneath. Big gaps can be taped with gaff or foil tape to bridge holes before applying the carpet. It's super forgiving material and easy to hide joins etc.

@charliebravo5562 10 ай бұрын

Nice job guys, I learned a lot.

@fisheromen18 2 жыл бұрын

great quality video. well done with the project too

@NomadicVisuals 2 жыл бұрын

Thanks! We really appreciate it!!

@kiwicol7383 2 ай бұрын

I would have liked to have seen the area above the doors before you added the foam also really nice ceiling looks great

@kingofswamis 10 күн бұрын

Well YA. YA YA WELL YA DUH

@dthomas3065 Жыл бұрын

Thank you very helpful

@NomadicVisuals Жыл бұрын

Glad it was helpful!!

@WillFly Жыл бұрын

Great video, thank you for sharing it! How much of the foam did you have to purchase for the job?

@NomadicVisuals Жыл бұрын

Thank you Will! We used 3 rolls of the foam - here’s the link amzn.to/3CXQmGs. Let us know if you have any questions.

@NorthwestLights206 10 ай бұрын

@@NomadicVisuals Hi there, what Spray adhesive did you use? I have used spray adhesive and had it melt through fabric before.

@NomadicVisuals 10 ай бұрын

@@NorthwestLights206 hi! We used 3M high strength spray adhesive. We got ours at Lowe’s.

@katydidnt3906 6 ай бұрын

Hi there. Those tail light panels have been designed to provide significant venting - is there a concern that the foam and fabric will completely cancel the needed air flow behind it? I had put sheep's wool insulation behind these panels and ended up with moisture accumulation to the point that the light assembly shorted out. I needed to replace it.