Im having the same issue on a 2010 insignia i just bought It only shows the message on cold but not wanting to leave it too long so its booked in in a few weeks . There is an upgraded part available which i should have this week It should be interesting to compare the two This shohld have been a factory recall so shame on vauxhall for this ! Excellent video chap ! 👍👍

Side notes the sump isn't held in with Torx bolts. They have pointier points. The proper tool is RIBE bolts. Not expensive for a set but make the job easier.

Great video, I will need to do this soon your video will save me a lot of struggle and time - thanks

There is an upgrade kit you can get,oem spec,its an aluminium oil seal, do the job once and never worry about it again.

Love it, no fucking about. . . on the cold driveway like all DIYers. I might see if I can get a nice cheap one and have a crack at this. Great explanation of the issue too. Good video mate.

Nice work and simple fix for such a bad failure point

Merci du renseignement, de tourner le volant moteur avec une douille pour pouvoir dévisser

Thank you very much for the helpful video

Got mine being done in the morning, started to have the warning on first cold start. Only happened since i gave it a oil change 🙄 2015 2.0 cdti 126k

I have a 2015 insignia 2.0 cdti I need to re- check I’m pretty sure I don’t have those notches in the gearbox to access the 2 sump bolts, maybe I’m wrong. My car has 50k running fine but came across these videos when checking how to change alternator wheel.

Always a good Idea to check conrods why the sumps off

Absolute Champ 🏆

Hello, first, thank you for taking the time to do these videos. I happen to have the same Insignia as you. Soon I will have to change this rubber to prevent failures. But for now, my main concern is that the other day my engine overheated, there is no leak of the coolant, and the service belt is perfect, so 2 possibilities remaining I think, the temperature sensor is faulty or the thermostat is malfunctioning, although I have tested this one, and when the fan turns on there is flow through the radiators. What do you think? Just one more thing, for me, is hard to find the OE or OEM parts that I have to change, for example, the thermostat, do you have any webpage were you search parts by your Insignia vin number? And also, do you know were to find or get a repair workshop manual of the insignia? Thank you so much again.

Slave cylinder went in my 2013 insignia, so I decided to change the seal and fit a full new clutch kit. It's a serious bit of work, but it should be worth it. I'll never know why they put the clutch slave cylinder on the shaft. I'd advise anyone to clean up the front sub frame and paint it because they are famous for rusting out and snapping. I'm cleaning up mine, and I'm going to oil the inside of it with a diesel gun.

only need to remove drive shaft carrier.

Hi very useful video. How long did it take to do cheers

I need help! I have a lot of black smoke and some liquid in between the engine and the firewall somewhere from the EGR I guess. I have seen craked EGR cooler cap as a common thing, is that all the problem there it shoots smoke and coolant even in the firewall direction? or I should look to something else in the EGR? I have seen your other video on similar subject, I would higly apreciate any information! Thank you and sorry for my bad English.

Apparently you don't need to remove rhe driveshaft only rhe driveshaft carrier bracket

Hello, I'm french. So, excuse my english😅. First, good job for this video, only english men make vidéo on KZfaq for this job😮‍💨. Si, thank you to you👍 Can you tell me if tour Gear box IS a M32 or a F40 please? We told me I would have to lower thé Gear box if it was a F40😮‍💨. Good road to you😉

£17 seal that can cause so much damage. Vauxhall should be recalling

Are the two connections at 2:54 the oil pressure sensors? I can't find anything to do with them 😂

hi, i have a constant vehicle service message coming on dash,, (no low oil pressure) when pluged in i get code P06DC engine oil pressure control solenoid valvue control circuit high voltage! / is this the same problem with my insignia too? or could it be just a oil pressure switch thanks 180k KMs

Do you need to replace oil pump whist doing the pick up seal? Or can you get away with just the seal?

If this seal start failing with no message, does oil vapor will come out from PCV too much more than normal?

Hi. Do you have the part number for this seal? Thaks.

Got the vauxhall astra gtc 2013 2.0 diesel is that the same engine that's in the insignia

Hi, does opel gasoline engines has the same problem with oil seal?

What's the reference of this seal

part nr?

Please wht is mechnics emai and phone?

Is it only the 2.0 diesels who had this problem? Can be quite expencive and be the death of a car.

How do we contact you?

Did Vauxhall ever fix this issue?

How you remove 2 small bolt on transmition side?

It's a such a dumb design.

?

What's your email address?