My sons car was due for the MOT, I noticed that the break light bulb was dead . This video is top notch, it explained fully the procedure. The biggest problem was getting the tool container out , it took two of us and 15 minutes, lots of pulls and wiggles hard work. If it was not for this video , I would have been looking for a retaining screw. Needless to say putting it back 20 seconds.

Sweet as this is. Explains everything you need to know.

Thank you for this video. I took one look, and considered paying Halfords to get the foam insert out. Your video will save me having to do that. Thanks again.

I had to change that right hand side brake light today and by goodness that tyre repair kit was an absolute nightmare to get out of the boot, I have arthritis in my hands and I was struggling like mad. Changing the bulb was easy but that polystyrene liner nearly finished me off. Thankfully I had a few spare bulbs lying around but they were the double filament type and luckily I found one single filament bulb out of a halfords kit. Definitely buy another single filament bulb to put back in the kit which will live in that ridiculously small glove box 😂

Exactly what I have been looking for, that tool holder part is really wedged in so I am truly scared of tearing it apart 😂😅 so now I see I just have to wiggle it for 20+ minutes

Nice one fella opened the boot thought it was old school change quick fix but looked at the wall of plastic and thought nope 👍🙏🏼

Just had to change both brake lights today good video thank you

Saved us a few quid with this, cheers mate.

Thanks for the effort saved me ages 👍👍

Very clear and handy! Thank you.

very good properly explained how to chang the back break light on the right hand side on corsa auto 2012

Cheers! Just noticed mine was out, this really helped :)

Cheers mate, very clear as exactly what you need to do.

Very helpful, thank you

Great video and that foam stuff holding the tyre repair kit is a bugger to get out

Thank you! 👍

Great video. Thanks for posting 👍

My foam insert was one solid piece just ended up taking a knife to it 🤦🏾‍♂️ but if it wasn't for your video I would of thought it was part of the body work it was in there so tight

Great video done mine with this video!

Careful what brake light bulb you get, my 2006 corsa has a single filament 21watt bulb that works as the stop and tail. It uses a reduced voltage to light it as a 5w bulb but gets brighter when the brake is applied. So it is not a standard 21w/5w stop /tail double filament bulb. Give your car registration to the spares place and they will check on the computer which bulb is listed for your car, or take the old bulb in.

Thanks alot

Very helpful, thanks.

Thank you,, so helpful 😀👍

Brilliant video helped me out alot thank you

Great video,tks a lot !!!

Thanks. This was really helpful.

Going to use this but other rear bulb. Hopefully don't have that toolbox wedge type problem.

I found the polystyrene thing came out a lot easier in pieces. 🤔

Cheers buddy

thanks man

This is exactly what I needed, so helpful! Thank you 😁

Straightforward

Very helpful amazing video thanks a lot :)

thanks a lot :)

is this how you change your reverse light too?

great video, just for clarification, is it a 21W for the brake bulb and a 21w/5w for the side light? Or can you use a 21w/5w for both?

How many brake light bulbs are there? I got Corsa D 1.2 2010. When I brake only the top LED light comes on where the rear window washer is. So I think the brake bulb that. Your doing is gone

need audio setup video

what bulb did you buy? mine's gone out the same as yours

I noted the boot a lot smaller then my sisters four door version.... just saying lol 🤷🏽‍♂️

Cheers buddy