HDMI PORT HOT SWAP Method. How To Quickly Replace a PS5 HDMI Port and Repair Missing Pad w/ Jumper.

Рет қаралды 60,782

Күн бұрын

Here's how to HOT SWAP the HDMI Port on a PS5.
If you need your HDMI Port repaired, contact us for a quote: www.vccboardrepairs.com/conta...
This method allows you to quickly swap out the port of a Playstation 5, Playstation 4, Xbox One, Xbox One S, Xbox One X, Xbox Series X and more.
I also go over how to run a jumper to a broken trace & how to replace the missing 0.1uF 0201 Capacitor.
What are your thoughts on the HOT SWAP Method? Do you already do this?
Let me know down below.
🛒New HDMI Port Replacement Part:
www.injuredgadgets.com/gaming...
or www.mobilesentrix.com/hdmi-po...
🛒Capacitor Next to HDMI, 0.1uF 0201: www.injuredgadgets.com/gaming...
🛒Cordless Screwdriver: amzn.to/46QHal8
🛒Extended T9 Driver Bit: amzn.to/3c6AfNl
🎥 Full PS5 Disassembly & HDMI Port Repair Video: • Damaged PS5 HDMI Conne...
🚨 Support the channel by checking out these links🚨
►Check out my new T-Shirts, Hoodies & more: merch.vccboardrepairs.com
►Amazon Storefront: www.amazon.com/shop/vccboardr...
►Join the new Facebook Group for Repair Techs vccboardrepairs.com/vcc-fb-group
►Let me teach you to Microsolder: vccboardrepairs.com/profixerr...
►Mail us your iPhone/iPad for repair: www.vccboardrepairs.com/conta...
🛒Buy The Seek Stand by VCC Board Repairs here: vccboardrepairs.com/buy-seek-...
🕶 Buy Macro Lens here: www.vccboardrepairs.com/buy-m...
📸Buy The Seek Compact Pro here: amzn.to/34I4whX
🚀Today's shirt can be purchased here: merch.vccboardrepairs.com/lis...
► Like us on Facebook: / vccboardrepairs
► Follow us on Instagram: / vcc_board_repairs
⚠ B2B & Wholesale pricing for mail in repairs is available for repair shops in the USA. Contact us for more information: www.vccboardrepairs.com/conta...
Please note: This page contains affiliate links. If you choose to make a purchase after clicking a link, I may receive a commission at no additional cost to you. Thank you for your support!

Пікірлер: 161

@FitzWyatt Жыл бұрын

Just did one and have a few critiques that made my job infinitely easier. 1. Prep both the new port and pads with low melt solder and flux, clean with isopropyl after. 2. Let the port fall out of the board upside down, that way you don't damage any pads. Cool vid!

@VCCBoardRepairs Жыл бұрын

If you do it right, you can swap the port within 30 seconds. In my video, the pads were already ripped so it didn't seem so quick But here's another video to reference on why hot swap, without any of the extra steps you mentioned, works so well www.tiktok.com/t/ZTRuhXqEE/

@ElohiSilverEarthVentures Жыл бұрын

I just did that same technique, just kind of winged it, didn't really know what I was doing,just figured it'd work well though,I got good at doing those tiny little tips off ends. Good video, thank you.

@MicroMageRepair 2 жыл бұрын

Always fun to see other people's approaches. Good stuff Mr. Cruz!

@VCCBoardRepairs 2 жыл бұрын

Appreciate it, man!

@trilexfix Жыл бұрын

I've had a lot of success using low melt solder to remove HDMI ports and you heat the ports up a lot less. Also getting it from the back is good too front or back works fine. The hot swap method doesn't seem terrible, the pins look soldered on well, I guess when I first started I would have pins fall off so I always try to use the most solder possible on pins because I don't want connections to break in the future so it's more of a pet peeve of mine now. Either way GOOD JOB JESSE!!!

@VCCBoardRepairs Жыл бұрын

Thank you!

@bradwest737 11 ай бұрын

This video was very helpful I now have the confidence to attempt to fix myself very informative just having the right tools and some practice will allow me to fix it if things doing this hot method seems like the best way in my opinion I have several kids that are hard on electronics so maybe I can make it a hobby as well Thank You !!!

@VCCBoardRepairs 11 ай бұрын

Glad it was helpful!

@smartphonerepair7555 2 жыл бұрын

Jesse you do great work and I love watching these videos. this method i have been doing for almost 7 years now but a personal suggestion from experience. i would not hold the heat gun under the board face up because this angle puts the hazardous ,acidic sometimes, flux fumes directly into the person working without proper ventilation and can cause all types of problems. you can still do the hot swap method with the heat gun facing down and will get the same desired effect. touch up the pins on the back and even sometimes a little bit on the legs and your ready to go!!

@VCCBoardRepairs 2 жыл бұрын

I feel like if there's danger from heating from the bottom due to any fumes, the same danger would be present from heating from the top. I generally don't put my face on the scope when heating from the bottom anyway. And I have a fume extractor. From my experience, heating from the top makes it easier to melt the plastic on the HDMI as well

@lingxioayu1068 5 ай бұрын

Thanks for the help. Not new to soldering but new to hot air machines. This was a huge help esp your settings. Again thanks a lot I hope you keep busy doing this kind of work :)

@VCCBoardRepairs 4 ай бұрын

I really appreciate your support. Thank you so much

@mrrobotto3321 17 күн бұрын

Just did one on my kitchen counter using a hercules heat gun on 850f @ 4/5 speed. Thank you sir.

@h11h2000 2 ай бұрын

Great job bro I'm trying to practice more so I can get that good

@ZEESHANSIALKOTI 2 жыл бұрын

EXCELLENT WORK YOUR ARE ALWAYS A HEAD FIRST I LOVE YOUR WORK

@VCCBoardRepairs 2 жыл бұрын

Thank you so much 😀

@SURGE101 2 жыл бұрын

Nice method Jesse, you could also prepare the port pins on all your hdmi ports when you buy them so they’re ready to go if you get any port repair jobs in. Great video as always.

@VCCBoardRepairs 2 жыл бұрын

Thank you! That's a good idea if you have free time 😅

@temyraverdana6421 2 жыл бұрын

It is an very interesting soldering method. Thanks for share it

@VCCBoardRepairs 2 жыл бұрын

Glad you liked it

@lgstar3363 Жыл бұрын

Thank u for your informative video really appreciate it.

@VCCBoardRepairs Жыл бұрын

Glad it was helpful!

@cmtechservice Жыл бұрын

Great instructional video!

@VCCBoardRepairs Жыл бұрын

Glad it was helpful!

@Johnellenberger1 5 ай бұрын

Nice work!

@TimSherman401 2 жыл бұрын

Really good quality video!

@VCCBoardRepairs 2 жыл бұрын

Appreciate it, man!

@NigelB-cz9bz 2 жыл бұрын

nice touch - will be trying this.

@VCCBoardRepairs 2 жыл бұрын

Awesome. Let us know how it goes!

@izydata Жыл бұрын

I found it very difficult, with only a magnifier glass, to replace the 100 nF cap. Managed to do it by heating the HDMI contacts on pin 2 and 3 after tinning them and before replacing the HDMI connector. Thanks for the video.

@VCCBoardRepairs Жыл бұрын

Oh wow. That's amazing

@xavieravila5336 Жыл бұрын

I took my ps5 to do this but it seems like it doesn’t look as crisp it may be in my head so you know if the place I took it to used a cheap hdmi port can it effect resolution? I have a hdmi 2.1 tv and all the bells n whistles cables Ect

@dannyfong6350 10 ай бұрын

Hey I seen your video where do you buy a PS five jumper . Are you technology little bit late?

@skeggjoldgunnr3167 Жыл бұрын

Most cleaning I do after work is with acetone. Jobs like this still have stubborn flux seeping out from under the port. I use a 50/50 blend of Tetrachloroethylene and N-Hexane for that. Known by the State of California to work.

@VCCBoardRepairs Жыл бұрын

Thanks for sharing!

@D4RK5iDERS 2 жыл бұрын

Nice method, never considered heat from underneath, I do like using low melt solder (93°c melting point) to remove the old port, might give this one a go though 😄

@VCCBoardRepairs 2 жыл бұрын

Yes, Low Melt is super helpful. Although when doing it like this, you don't even have to do that. Saves so much time. Although i've never heard of 93C melting point solder. Do you have a link?

@D4RK5iDERS 2 жыл бұрын

@@VCCBoardRepairs it was from RS components, Chipquik SMD4.5NL 👌 fun stuff to play with 😂

@TonyToneFixMyPhone 2 жыл бұрын

I've used this underneath method for years. Louis showed us this like 10 years ago. LOL But I usually only do this to harvest donors.

@VCCBoardRepairs 2 жыл бұрын

This is a great method for harvesting components and FPCs!

@TimSherman401 Жыл бұрын

Thanks!

@VCCBoardRepairs Жыл бұрын

Thank you so much!

@TommydaOG 2 ай бұрын

Thanks for video I just broke my ps5 hdmi port

@jefftuttlejr Жыл бұрын

100th comment 🎉 amazing video. Nice job buddy.

@VCCBoardRepairs Жыл бұрын

Thank you!

@aragon2235 Жыл бұрын

Definitely going to take the hot swap advice. The tinning of the leads makes perfect sense before placing the port. I always worry that i will melt plastic in these types of components so this will help immensely. Thanks for the video and the tips. Any chance you could make a video of how long the tear down takes to get to that point on the board so i can accurately estimate costs for clients? If you already have a video on that then i apologize.

@VCCBoardRepairs Жыл бұрын

I have a video already on my channel

@bradwest737 11 ай бұрын

I agree with the tiny terminals tinning is a must to get a precise solid solder connection

@ItalianRetroGuy 2 жыл бұрын

Great video, I don't have that much room on my microscope to hang boards off the desk and use the hot air station, while still being able to point the microscope at it. So I probably won't use this technique in my videos lol

@VCCBoardRepairs 2 жыл бұрын

I had to move my scope around to allow it to reach off the edge. Trust me, make it happen & you'll find it's worth it!

@ItalianRetroGuy 2 жыл бұрын

@@VCCBoardRepairs mine is bolted to the wall :) it's high enough that I can do it directly on the desk if I use angled nozzles

@yatikarton2735 Жыл бұрын

Hello, thanks for the Video. I am a bit into soldering and a friend of mine wants me to repair a HDMI port on a Ps3 and I didn't know how to go about it. This was helpfull. Did you use low melt solder?

@VCCBoardRepairs Жыл бұрын

Great. Watch the videos on my channel to get a better idea of soldering. Consoles in general require a lot of heat. I may have used 183C solder. But honestly dont remember.

@Vinnie2x 2 жыл бұрын

Hi 👋 . I'm fairly new to PS4\5 Repair. I lost a small cap just below the hdmi port on a ps5 replacement. I do not know it's value. It bridges two of the hdmi pins. Could you please advise. Will the video signal function without it and or where can I find out what it's capicatance value is? Thank you.

@VCCBoardRepairs 2 жыл бұрын

Check the video description. I linked to the cap that goes next to the pins of the HDMI port.

@hove131 2 жыл бұрын

Switched to it recently for better feed through.

@VCCBoardRepairs 2 жыл бұрын

Awesome!

@JohnnyP414 2 жыл бұрын

Hey Jessie, what kind of gloves are you wearing? Do they resist heat? Thanks for the cool videos

@VCCBoardRepairs 2 жыл бұрын

I just use regular nitrile exam gloves: amzn.to/3yVBBCd No, they're not heat resistant per se, but the thin layer of nitrile does add a very tiny fraction of heat protection. Enough to give you a heads up that you're being burned

@trevorjames5493 Жыл бұрын

Oh yeah and I forgot to ask when you are jumping the pins say I'm going to jump every single one , you connect it to the spot above it but what about the ones in between I think there's three or four that are ground I think where do they get jumped to? Can I just scratch anywhere on the board to reveal copper and connect them to that since they don't have their own pin above it?

@VCCBoardRepairs Жыл бұрын

the ground pins can generally be skipped. but if you want to jump them, jump them to anything that is ground.

@belaircomputerguyllc4001 Жыл бұрын

How do you keep the components directly beneath the port on the opposite side from falling off with that heat? What temps are you running as well?

@VCCBoardRepairs Жыл бұрын

Surface tension keeps them in place. Temps are shown in the video.

@electronicsmix8880 Жыл бұрын

Hi, what about the diode, is it BAS316? Do you have any information about the component which connected to the anode of the diode. Thanks in advance

@VCCBoardRepairs Жыл бұрын

I'm not sure which diode is that? Is it the one nearest to the HDMI port? If so, you can use any iPad backlight diode.

@electronicsmix8880 Жыл бұрын

@@VCCBoardRepairs Hi Jesse, if you take a look on your video @ 5:50 you will see this diode over the HDMI on the left side. To the left of that diode there is a component which is connected to its anode. Do you have any details about this component? Thank you!

@trevorjames5493 Жыл бұрын

Does it matter what size jumper wire we use ? as long as it doesn't rub on anything around it? I got this one its 0.10 mm Chinese stuff or is that too thin ? It's almost like hair, it looks thicker in all the videos but I think that's just because it's under the microscope possibly??

@VCCBoardRepairs Жыл бұрын

It doesn't matter

@RejectedManiac Жыл бұрын

Does the newest version of the PS5 have a different HDMI connector that launch edition? It looks different to me and I'm not sure if the HDMI connector is interchangeable. Thanks

@VCCBoardRepairs Жыл бұрын

Yes it's all the same.

@andyleboeuf1194 2 жыл бұрын

by jumper what were you using? where can i buy it? why were you using it? i just started to learn to repair stuff and i need as much help i can get, thank you.

@VCCBoardRepairs 2 жыл бұрын

This is the jumper wire i used: amzn.to/3QlWz51 I had to rebuild the broken trace.

@foxhound2992 Жыл бұрын

If the HDMI is undamaged do you still replace it or just re-tin the solder to fix the no signal issue?

@VCCBoardRepairs Жыл бұрын

You have to replace it, as the HDMI port is likely internally damaged.

@manuelpedro5727 Жыл бұрын

Do you know what component that's under the hdmi. It's a small black component.

@VCCBoardRepairs Жыл бұрын

i think you're referring to the diode.

@broflofsky7813 2 жыл бұрын

Jesse, help :) iPhone 7Plus, all works but no front cam. Flex and cam is OK. I checked diod mode values on Front Flex connector and all is about to correct value. Device fall from running car window.

@VCCBoardRepairs 2 жыл бұрын

Great question to post in my group Https://www.vccboardrepairs.com/vcc-fb-group

@broflofsky7813 2 жыл бұрын

@@VCCBoardRepairs Ok, Would you let me in? :)

@ckarouach 2 жыл бұрын

Good method even takes little long

@VCCBoardRepairs 2 жыл бұрын

Thank you!

@jameysummers1577 Жыл бұрын

Wow! Thats a lot of heat! Those grounding traces must be a mile thick.

@VCCBoardRepairs Жыл бұрын

yes for sure.

@aktech3271 Жыл бұрын

What soldering wire do you recommend?

@VCCBoardRepairs Жыл бұрын

Kester. I have it listed on my site Www.vccboardrepairs.com/gear

@kymgershon9690 8 ай бұрын

What is the green liquid he used?

@VCCBoardRepairs 8 ай бұрын

UV Mask

@kylea7714 Жыл бұрын

Rubbing alcohol can be used to clean off the flux

@VCCBoardRepairs Жыл бұрын

Sure can!

@davidcrittenden2129 Жыл бұрын

Is there a substitute I can use I don't have Flux and I don't know if I have the proper Sauder. I'm pretty nervous about doing the repair iv never done this before

@aragon2235 Жыл бұрын

Great tip and I completely agree.

@yavuzakbina5835 7 ай бұрын

does it mather wich side the cap is installed?

@VCCBoardRepairs 7 ай бұрын

Like the orientation? not for these types of caps

@TechMDYoutube 2 жыл бұрын

Been doing this for years I figured this method out like 12 years ago lol

@VCCBoardRepairs 2 жыл бұрын

oh awesome!

@MegaOdunn Жыл бұрын

What's the temperature of your heat gun?

@VCCBoardRepairs Жыл бұрын

If you want the video, I say what temperature to use.

@benmadiyanis9460 Жыл бұрын

It works without the capacitor near the hdmi ?

@VCCBoardRepairs Жыл бұрын

Technically yes, but it does look to be important, so i always replace.

@timmahotool3714 11 ай бұрын

The heating from the bottom hot swap is great until you bump the board accidentally and lose all the flowing parts. Also you are placing tremendous amount of heat on the board. Obviously you have replaced alot of ports as this is not a beginner move. I prefer to put the port in cold. Excellent job though!

@VCCBoardRepairs 11 ай бұрын

Hot swap method is a great method for HDMI port replacements. It should be done by professionals who know how to solder. If you're a newbie, definitely requires practice first and training if possible. Any method is risky without proper technique or training.

@UrielRD13 5 ай бұрын

XP. A

@daviddelacruz1948 Жыл бұрын

Hey boss, i took apart my Ps5 to find out this is exactly my problem, how do i get in touch with you to send you my board to get fixed?

@VCCBoardRepairs Жыл бұрын

Great. Send me a message for a quote: www.vccboardrepairs.com/contact-us

@aaronnunez5466 Жыл бұрын

I’ve never soldered before, if i go and buy a kit and dont have a microscope do you think i can do it with no experience

@VCCBoardRepairs Жыл бұрын

Most likely not. It does take practice and experience to be able to handle a job like this. It may look easy on video, but once you have it in front of you, it can go very bad if you dont know how to handle it.

@aaronnunez5466 Жыл бұрын

@@VCCBoardRepairs is it really that hard? I’m pretty good at using my hands and it’s my only option unless I want to pay $300

@VCCBoardRepairs Жыл бұрын

@@aaronnunez5466 If you have no experience soldering with a hot air station, yes, it will be difficult. Just keep in mind, most repair shops will charge you extra if the board has been worked on previously & is worse shape. My recommendation would be to practice on non-working boards, so you can see what the actual job entails

@deeezShorts Ай бұрын

How much do you charge to do this? If I was to send my ps5 in? Also great video!

@VCCBoardRepairs Ай бұрын

Thanks for watching! You can message me for a quote: www.vccboardrepairs.com/me

@Blackbelter 2 жыл бұрын

Can we use the thermal paste in APU in PS5?

@Nectronixx 2 жыл бұрын

No liquid metal only

@Blackbelter 2 жыл бұрын

@@Nectronixx do you k ow what type and where can buy on it?

@VCCBoardRepairs 2 жыл бұрын

I haven't tried this but it has really good reviews: amzn.to/3nS6geL

@codyneedham1591 2 жыл бұрын

Where can we get replacement pads?

@VCCBoardRepairs 2 жыл бұрын

In most cases, running a jumper wire is better. If you want the soldering lugs, you can buy them here: www.injuredgadgets.com/wylie-soldering-repair-spot-welding-piece-patch-solder-lugs/?acc=3d2d53e5abcd70e24cc444935b88e6ac21

@nichademusstroud7578 Жыл бұрын

I was unable to contact you for a ps5 hdmi repair inquiry as you site is flagging as containing maleware. Is there another means to contact?

@VCCBoardRepairs Жыл бұрын

Oh wow. I'll get that fixed. You can text me directly 702-670-2711

@nichademusstroud7578 Жыл бұрын

@@VCCBoardRepairs my friend sent you a text regarding a repair. It's his ps5 that intermittently loses the video signal. He's able to play for a little at a time until the screen goes black. The HDMI cable is quite hot to the touch at the ps5 port. Thank you.

@_mylastname Жыл бұрын

I like to pre tin my trace jumpers.

@VCCBoardRepairs Жыл бұрын

Sweet!

@kylemanning-riley5853 2 ай бұрын

Has someone asked yet where you got the heat gun?

@VCCBoardRepairs 2 ай бұрын

From here ⭐ Atten Hot Air Station: amzn.to/3tjYIYl

@CB27 6 ай бұрын

Which scope is that please?

@VCCBoardRepairs 6 ай бұрын

⭐ Parco Stereo Microscope: amzn.to/48coNYN

@CB27 6 ай бұрын

@@VCCBoardRepairs Thank you. Looks the same as the Amscope SM-4TPZ

@wendellgreenidge3362 2 ай бұрын

So what stops it from breaking again? This is my third time replacing the port and it replaced by a well know electronic repair tech.

@VCCBoardRepairs 2 ай бұрын

Could be a few reasons. 1. Bad solder work by the repair shop, causing the port to fail easily 2. Low quality replacement port. 3. Or you keep damaging it by unplugging & replugging it and not lining up the cable when doing so

@wendellgreenidge3362 2 ай бұрын

@@VCCBoardRepairs so is there a such thing as a reinforced hdmi port?

@michealkolbil9290 7 ай бұрын

the work u did are sure after installing the machine back it work?? sometimes you guys are not real to be honest

@michealkolbil9290 7 ай бұрын

i saw brown part of in the hdmi cos it was forced to be taken out and one leg wont sit to get contact

@VCCBoardRepairs 7 ай бұрын

Yes it worked. We are a real business and repair these on a regular basis.

@playstationstore1503 Жыл бұрын

Bro what kind of flux do you use, the name if not difficult?

@VCCBoardRepairs Жыл бұрын

Amtech 559 www.vccboardrepairs.com/gear

@playstationstore1503 Жыл бұрын

Do you use this mode ? AMTECH NC-559-V3-TF 30гр. tf-v3-030 138-300°C ORIGINAL USA

@Blas1474 Жыл бұрын

What's the little part for??? a local shop replace my HDMI. And didn't put that part back !!!😬😬

@VCCBoardRepairs Жыл бұрын

What little part? The capacitor?

@Blas1474 Жыл бұрын

@@VCCBoardRepairs i think it is tiny part stock in the twizzers

@yuelbiniam995 Жыл бұрын

Can you fix mine

@VCCBoardRepairs Жыл бұрын

If you're in the USA, then yes!

@zxrjimmy1 2 жыл бұрын

I do hot swap all the time

@VCCBoardRepairs 2 жыл бұрын

This is the way!

@glenmetcalfe9784 Жыл бұрын

wow so professional.wish you lived in my neighborhood!Recently contacted a local repair shop and they quoted this repair at $289. I hung up because I was so disgusted that PARASITES actually have the nerve to try and charge people this much.

@VCCBoardRepairs Жыл бұрын

If you're in the USA, send me a message for a quote: www.vccboardrepairs.com/contact-us We can beat their price :)

@glenmetcalfe9784 Жыл бұрын

@@VCCBoardRepairs im in canada bro,thanks anyways

@VCCBoardRepairs Жыл бұрын

In that case, reach out to my friends at Phone Doctor - Cell Phone Repair and Electronics (604) 217-5529 maps.app.goo.gl/PCgKJvg7WkvQdriG7?g_st=ic

@clownlivesmatter7925 6 ай бұрын

Looks to hard for me. Wish i knew a trusted place near me to do this

@VCCBoardRepairs 6 ай бұрын

If you're in the USA, we can help! Send me a message for a mail in repair quote: www.vccboardrepairs.com/contact-us

@leso204 Жыл бұрын

made that job harder should of cleaned the board after removal fixed the pad then re-attached the new port ...........

@VCCBoardRepairs Жыл бұрын

Good point

@KaydenPassi 5 ай бұрын

Yep… sending it to the tech store 🤦🏽‍♂️🤦🏽‍♂️

@VCCBoardRepairs 2 ай бұрын

We'd be happy to help as well. You can request a quote at our website: www.vccboardrepairs.com/contact-us

@EvilLabsSolutions 8 ай бұрын

As a fellow technician, I have a couple of problems with this . 1. You should use low melt solder so you don't have to overheat the board. 2. If you're heating it from the bottom, in order to take it off, you should turn the board upside-down so the HDMI port will fall off by itself. (Les risk of ripping pads) 3. You need to wick off the old solder and clean up all the flux . Use fresh flux and solder the pads. 4. Clean up, use fresh flux, solder the pins, and place the HDMI port in its place. 5 . Then you can decide if you want to flow it or solder it pin by pin. I know technicians have their own way, but just heating it up and swapping it to a new one and skipping all the steps above is wrong. Hope this comment helps .

@VCCBoardRepairs 8 ай бұрын

We've been skipping all your steps & have had 100% success rates with no warranty issues. I'm confident hot swap method is not an issue and we back it with a lifetime warranty.

@repaironwheels Жыл бұрын

comment

@VCCBoardRepairs Жыл бұрын

🙌

@Healthlife161 7 ай бұрын

Not a good Technician bro you loss both capister

@VCCBoardRepairs 7 ай бұрын

I agree. Going to close down my shop. Thanks for letting me know.

@kemyst515 Жыл бұрын

The fact that 2 year old or less systems are having this many fucking problems and Sony is just making us either try to do it ourselves or go spend $200+ to get it fixed is asinine. I will not own another sony product after the trash ass ps5

@VCCBoardRepairs Жыл бұрын

from my experience, most of the devices that come into my shop, are damaged HDMI ports. this is from physical damage caused by the user. so you can't really blame Sony for that.