17-06-2024 Good day Ciotti and GG how are you all doing? 00:01:47 The best pilot ever😉 00:02:04 On this stream….. 00:07:52 What color frame? 00:08:22 last pin vice sold! And why they work so good. 00:18:44 Support your GG. 00:26:00 My nurd googles arrived today. They changed my life. 00:30:27 Finally got the LiteAF and titanium screws. Dry weight is 15.49g 00:31:04 It's the lightest that it can currently be without crazy mods. 00:31:10 Why props in? 00:38:33 Do Whoops react differently to props in/out vs a 5" (where it doesn't really matter)? 00:40:24 What whoop will be taken apart? 00:49:22 Your thoughts on the new t-motor 5inch frame?( its fpv). 00:51:15 I put 40k motors on my mob6 hdz. I’ve had to check the don’t spin motors on arm to keep it from taking off on arm. Not fly away but it comes off the ground. Is there a better way? 00:54:36 You need to get an affiliate link for Wrekd fpv. 00:56:35 Do you know what the camera angle is on the old Mob6 frame? would you say it's less than the G string? I'm after a low camera angle, 15-20 degrees. 00:58:01 The Algorithm gave me what looks like your 1st meet w Bardwell. He streamed from your house 4 years ago. You said paraphrased, "I don't like to fly cinematic, it's too hard" Had to laugh. 01:02:34 Let’s take a look how the rpm looks like. 01:07:34 If u have to build two new chase whoops what would u build with 03? What size with new restrictions ? 01:14:30 Don’t on 5in. you get so much shit splatter on your lenses with props in. 01:15:13 Could you reinforce the weak spot on the black frame/green motors with e6k? 01:16:19 Favorite 75mm frames? got a mob7 analog 1s 01:16:43 I turned tune all the way down. 01:17:18 Could you run the Meme Motors on a 75mm? 01:17:50 The new T-Motor Frame 01:22:41 OK. I tried the "throw it in a river" step of your troubleshooting guide. Now what? 01:22:55 Think he meant MOTOR_STOP in the motors tab 01:23:00 What motors would you use for a 2s toothpick with 45mm triblade? I was considering the sub250 0803 19k's. 01:23:50 Where is the batwing info so that I can have it printed., thanx! 01:26:53 Arm mounting looks like the screws will shear before the arms break which means new mid plate too. Also basically zero motor protection 01:27:33 Basically the same argument as Right to Repair. Voting with your wallet is important 01:27:43 Do you have an AUW you like for 2.5in? School bus not toothpick. Debating stack + heavier frame or AIO + lighter frame. 01:31:10 You're not alone! Lack of specs pisses me off. Motor weight with ZERO wire should be mandatory, or at least how much wire used when they took their weight is a big one for me. 01:29:20 VCI 0702 29,000kv Motor Testing. 01:30:24 Rubbing prop solution. 01:34:12 How to check your props if they are out of balance. 01:44:54 Something is not working good, let’s check it in Betaflight. 01:47:50 What is the issue? 01:49:46 Keeping it al so secretly…….. 01:53:15 Please put the uav tech preset on and fly it anyway. 01:59:44 More test flying. 02:03:18 Stealing cookies!!! 02:04:21 Teddy pupping up 02:10:21 Entering Stevie wonder mode. 02:20:42 I’ve never used the filters tab. when you adjust filters what do you adjust? just like for pids you just touch the first 2 sliders normally. 02:26:24 I always thought that the gyro frequency should be higher than the PID loop frequency, but I saw both of yours as 3.20khz. is that acceptable for builds? 02:28:44 What kind of car guy are you? 02:32:20 Mustang Miata are like two polar opposites. 02:35:20 Why does the Mobula 6 2024 canopy suck so bad? I’ve got to swap for the old mob6 canopy The motors are almost good enough, but not quite there. 02:38:54 Ciotti favorite driving footage. 02:36:02 My parents run a local car show and I've been trying to get them to do autocross but it's just so much for a small team to do, also insurance sucks 02:42:08 What's your opinion of the monster Miata 02:44:02 Would they go out of state for that? I don't believe there's anything in Delaware. 02:48:56 Have you heard of the Jag V6 swaps in Miata’s? Same weight as the 4 pot but so much more power 02:50:17 The Jag V6 swap makes very close to 250hp stock and would cost a lot less than 15k 02:51:50 It's not more weight though, the V6 is aluminum, the engine you swap in was considered by Mazda before they pulled the project. 02:53:22 From a couple a builds I've seen on YT you really don't need to upgrade anything else. Some move to the 5 speed for better gearing though. 02:54:50 Do you prefer the K to the B? Stay safe everyone and have fun flying

The mob 6 HDzero eco.. with the 28000kv motors.. that tune IS cranked up.. so I’m sure adding the 40000kv motor will have some issues..

@CiottiFPV….I just watched a video from @FPV vegan where he dove the Empire State Building with a tiny whoop! I wonder how he runs his props.

Saw that video also.. defiantly cool

Hi I see your nice videos, and must feed back on whoopstore 3, I got 3... open them and add solder to BT2 plugs, not enough was added, open up unsoleder fan remove the screws, board pops out, or Look at pins near heat sink and solder, boom great units...

I've been able to get rid of that annoying heart thing in the YT chat. I put notes in Discord "News"

My hand are too big for those tiny screws

Crunch, crunch, crunch, crunch, crunch..mmmph.. crunch, crunch, crunch crunch ROTFLMAO!!

Have you ever thought about a triple rotor swap rotory for the mazda? That would be interesting.😅

Im building up my first 65mm freestyle whoop right now, was wondering if you think its possible to have a rig that can do freestyle well, and follow rc drift cars well - or is doing both not really possible with these? PS: your videos have been invaluable to me while figuring out parts, im new to this side of RC - been drifting for a while and always been on the fence for fpv! Someone came to the track with a tinywhoop and was following us the other week and i got the bug HAHA