Vibration Analysis for beginners 2 (how to start your Predictive Maintenance)

No video

Vibration Analysis for beginners 2 (how to start your Predictive Maintenance)

Рет қаралды 108,815

ADASH

Күн бұрын

Пікірлер: 32

@priyomgoswami4327 3 жыл бұрын

The way you explained in all your videos is quite phenomenal. Loved it.

@AdashCompany 3 жыл бұрын

Glad to hear that

@ryanbowden9904 2 жыл бұрын

The videos are absurdly helpful. Helping me set up maintenance plans and efforts for multiple clients whos facilities we maintain electrically. Thank you!

@sunay9011 3 ай бұрын

00:46 haahaahahahahaha I use these videos for my graduation work, finally there was an unexpected reason for me to laugh, and at the same time useful, special thanks from Azerbaijan

@mielalexanderii4675 Жыл бұрын

Thanks for this very informative video.

@jackmittas8814 3 жыл бұрын

Prefect and to the point.

@Ashop0010 7 ай бұрын

Thanks for sharing

@nareshsachan130 Жыл бұрын

Very useful for beginners

@demohmand 5 жыл бұрын

Great! Keep it up team Adash!

@mohammedalhaidery957 5 жыл бұрын

Great! Please keep uploading this type of vedios

@zapisanakartka3605 3 жыл бұрын

Great video! Thanks a lot!

@vikasdhobale8787 7 ай бұрын

Hi Team your Vibration monitoring system is Compliance withAPI617

@AdashCompany 7 ай бұрын

Sorry, our systems does not comply with API617. But it does not stop them to be great vibration monitors being sold worldwide.

@actionwoman2477 2 жыл бұрын

thanks a alot

@siroossh3179 10 ай бұрын

I use of spm equipment for measure vibration

@AdashCompany 10 ай бұрын

Ok, thanks for information.

@gajimafeet 9 ай бұрын

thanks for the help Do you have info on frequencies and what they mean

@AdashCompany 7 ай бұрын

This is very general question. There is endless types of machines and their applications in particular industries. Every machine or machinery set (e.g. motor with gearbox and pump) generates vibrations on specific frequencies according to their construction and other parameters such as speed, load etc. There are speed frequencies, gear mesh frequencies, bearing frequencies, drive belt frequencies to name a few. Therefore there is no general answer to your question.

@derixmaclang 4 жыл бұрын

I almost stopped the video at 0:50. Haha

@kongor434 2 жыл бұрын

Hello Adash! It seems like you're using "cold welding" in order to fix the measuring point at 2:11. So my answer is simple - how does the "cold welding" layer affects on vibration level values? Do your measurements become more precise? And does it affect your high frequency vibration (acceleration)?

@AdashCompany 2 жыл бұрын

It is actually not a cold welding. It is epoxy glue which has the properties like a metal when dry. Your measurements will be repeatable and high frequency bearing signals will be transferred better than using finger tip or magnetic base for curved surfaces.

@ahmedzuhair4474 2 жыл бұрын

2/12/2021

@envitech02 Жыл бұрын

2:33 Can't we put the sensor on one of the two bolts that secures the bearing housing together? But if we do so, can we get an accurate reading since the bolt head appears smaller than the surface of the sensor?

@AdashCompany Жыл бұрын

That is not a good idea. Yes, bolt is smaller than the magnetic base of the sensor. These bolts are not ideally flat and the sensor will rock / swing on them. More over, the bolt actually behaves as a spring and it will damp a lot of high freguency (bearing) signals.

@envitech02 Жыл бұрын

@@AdashCompany Thank you sir. Best regards from Malaysia!

@user-ih5iv7qr4t 11 ай бұрын

When measuring vertical, horizontal, and axial vibration, do you compare each measurement to the maximum limit? or do you calculate some sort of resultant or average then compare it to the max?

@AdashCompany 9 ай бұрын

This is difficult question as there is no general maximum vibration limit. It depends on machine size, type, speed, load and other aspects.

@priyomgoswami4327 3 жыл бұрын

where do we need to place the tri-axial accelerometers in case of monitoring a gearbox, please help!?

@AdashCompany 3 жыл бұрын

Vibration analysis on gearboxes will be surely more difficult due to more shafts, gears etc. Ideally you should measure on each bearing house of each shaft if they are accessible.

@edgaromarreynatorres3940 4 жыл бұрын

if the motor doesn't has point of mesure, where can i mesure?

@AdashCompany 4 жыл бұрын

See this video from 3:28 about magnetic base for curved surfaces. The idea is to measure as close to bearing you can in order to get good signal from it. And to have good information about mechanical state of this part of the machine.