Рет қаралды 1,525
В данном ролике, я покажу, как я решил проблему с пусковыми токами на глубинном насосе скважины. Проблема заключалась в том, что при пуске насоса, возникал большой пусковой ток и нагружал инвертор. Если в данный момент запуска на инверторе была другая нагрузка, то инвертор уходил в защиту и в момент пуска "высасывал" из батареи большое количество энергии. Решил проблему путем установки частотного преобразователя с датчиком давления 4-20ма. Теперь насос плавно запускается и поддерживает необходимую производительность в зависимости от расхода воды. При остановке, насос плавно снижает обороты и останавливается.
Ссылка на обзор домашней солнечной электростанции • Солнечная электростанц...
Ссылка обзор монитора батареи.
• Монитор для батареи с ...
Ссылка на обзор монитора батареи 120 кВт.ч
• ✅Обзор Smart BMS Charg...
Ссылка на обзор батареи 36 кВт. ч
• ✅Солнечная электростан...
Ссылка на личное подсобное хозяйство
• ✅Солнечная электростан...
Почта для связи и предложений solarhome777@gmail.com
#солнечныепанели
#солнечнаябатарея
#солнечнаяэлектростанция
#подсобноехозяйство
#батарея
#bms
#batteryequalizer
#liion
#off-gridlife
#solarpowerstation
#offgridpowerstation
#solarhotwater
In this video, I will show how I solved the problem with inrush currents at the deep well pump. The problem was that when starting the pump, a large inrush current occurred and loaded the inverter. If at the moment of starting the inverter had a different load, then the inverter went into protection and at the time of starting "sucked" a large amount of energy from the battery. I solved the problem by installing a frequency converter with a 4-20mA pressure sensor. Now the pump starts smoothly and maintains the required performance depending on the flow of water. When stopped, the pump smoothly slows down and stops. Link to a review of the home solar power station • Солнечная электростанц...
En este video, mostraré cómo resolví el problema con las corrientes de entrada en la bomba de pozo profundo. El problema era que al arrancar la bomba, se produjo una gran corriente de entrada y se cargó el inversor. Si en el momento del arranque, el inversor tenía una carga diferente, entonces el inversor entró en protección y en el momento del arranque "absorbió" una gran cantidad de energía de la batería. Resolví el problema instalando un convertidor de frecuencia con un sensor de presión de 4-20 mA. Ahora la bomba arranca suavemente y mantiene el rendimiento requerido dependiendo del flujo de agua. Cuando se detiene, la bomba disminuye lentamente la velocidad y se detiene. Enlace a una revisión de la estación de energía solar doméstica • Солнечная электростанц...
In diesem Video werde ich zeigen, wie ich das Problem mit Einschaltströmen an der Tiefbrunnenpumpe gelöst habe. Das Problem war, dass beim Starten der Pumpe ein großer Einschaltstrom auftrat und den Wechselrichter belastete. Wenn der Wechselrichter zum Zeitpunkt des Starts eine andere Last hatte, ging der Wechselrichter in den Schutz und "saugte" zum Zeitpunkt des Starts eine große Menge Energie aus der Batterie. Ich habe das Problem gelöst, indem ich einen Frequenzumrichter mit einem 4-20-mA-Drucksensor installiert habe. Jetzt startet die Pumpe reibungslos und behält die erforderliche Leistung in Abhängigkeit vom Wasserfluss bei. Beim Anhalten verlangsamt sich die Pumpe sanft und stoppt. Link zu einer Überprüfung des Solarkraftwerks • Солнечная электростанц...