I'm listening to this through my speakers within earshot of my lady. Can we make a gentleman's agreement that whenever mentioning prices, we cut it half and throw a wink in the video?

YES. More Podcasts with Tucker and Scott.

I've been handloading for around 25 years now and still learned a few things watching this one. Probably one of the best things about handloading is the new ways to learn!

I am one of the "Handloader" that is a down the rabbit hole doing everything to improve accuracy from neck turning to weighing primers and powder measuring to .02 of a grain!

I think its really important to go into it being honest with yourself as to what your reloading goals are. A competition shooter will have very different needs than a hunter might. As a hunter, if i load 100 rounds per year, i shoot more than i normally would. I can get by with a lower cost reloading setup. I can make premium ammo for the cost of the cheap factory stuff. I can mke it shoot as well or better than factory ammo. But most important to me is everything I've learned about ballistics and terminal performance as since i started reloading 4 years ago. But i do enjoy the nerdyness of seeing how well i can shoot my own ammo. And then the capstone was the 1st time i killed an animal i hunted with ammo that i made. That was cool.

I can see Ryan gnashing his teeth over missing this topic.

I have a confession to make, I only got into reloading so I could justify purchasing more guns. I used it as an excuse to afford ammo for older or obscure cartridges. With that factored in, it has done the exact opposite of saving me money.

I have youst started reloading in Norway and finding info like this is difficult except for the reloading 101. So thank for the podcast have a nice day

I started slowly with camera gear when I first started with photography, and I don't regret buying entry level gear at first. It taught me to appreciate what I had, and to learn what would be required if I wanted to reach the next level. If someone starts with less expensive gear, they can always sell it later if they find they no longer need it. If, on the other hand, you start with a purpose in mind, and have a loftier goal (like I do, regarding reloading, though I have yet to start), I play on buying a Lyman 8 turret press that comes in the Ultimate kit at Cabela's, if I'm going to do it at all - because I don't want to buy a single stage press and have to swap out dies all the time, as that's a time sink I'm willing to spend the money to bypass. Just like anything else, I don't want to buy the most expensive thing out there, because I'm not independently wealthy, and I just don't need the top end stuff - but I don't want the cheap stuff either, because it won't last very long - but if I start by buying a good setup, and I love it, I will keep going, and I won't regret the $ spent. On the other hand, if I don't want to continue with it, I'll be able to sell that good setup for a reasonable price, to at least get some return on my investment. Edit: Erik Cortina mentioned that when he measures for seating depth, when lifting the bolt, he does it quickly, not slowly - and he explains why slow is not a good idea.

16:18 You don't save money on any blasting ammo by rolling your own. If you're going to be a reloader, you have to WANT to do it, because it's absolutely work, if done properly. You have to be the kind of guy that really enjoys fiddling with stuff. The ONLY places you "save money" in reloading is: 1: ultra high quality ammo(mentioned in podcast), 2: ultra special custom ammo that is not available anywhere at any price(this is especially true for shotgun shells), 3: insanely rare or obsolete/ antique or wildcat ammo(basically things that you have to hand load for, or it ain't ever gettin shot). If you just want to get out and live that mag dump life, don't even remotely think about reloading. Buy whatever is cheap this week, by the case, and let your ghetto blaster sing.

One of the most information rich channels on KZfaq!!! Love listening to every video you guys put out! Keep up the great work!!!

I am in no ways an expert reloader, but I think my biggest piece of advice would be to remember to keep it fun. It is so easy to get overwhelmed with load development. Sometimes it’s easy to over complicate things that really don’t need to be that complicated. You will enjoy your reloading journey much more when you have fun with it!

Need to pick a powder? Go to the Nosler reloading data and they tell you what powder was most accurate in their tests. The Sierra manual will give one powder for hunting and (sometimes) another for accuracy. When in doubt, call the bullet manufacturer. This conversation focused on hand loading bottle necked cartridges for bolt action rifles. I enjoy that myself, but there are other concerns when you’re loading for a semiauto rifle or a handgun. On the subject of equipment, I think the “buy once, cry once” approach only works for some people in specific circumstances. If you start with a single stage press, manual trimmer, etc., you will figure out whether or not you even enjoy hand loading. You’ll also learn what you want out of a “better” press/trimmer/scale… However, everyone needs a Forster Co-Ax single stage press IMHO. It’s simply a better mousetrap, and it was the last of 4 presses I bought. If I needed buckets of ammo for 3-gun competition, a Dillon progressive press would make sense but I just don’t produce enough of any one cartridge to justify that. I would encourage people starting out to try different things. If you got Hornady dies for .38 Special, try a Lyman set for the next cartridge. Buy a Redding Profile Crimp Die for a revolver load and see if you like what it does. I really like Forster die sets for rifle cartridges, but try Redding too. YMMV

Yes, this was pretty nuanced, but there are lots of us out here who LOVE it. Getting to hear two very experienced reloaders weigh in on what works (for them) and doesn't is priceless.

Your process being stream lined to the most efficiency is KEY! FOR RIFLE - My process is - Dry Tumble, Deprime/resize or necksize, Wet Tumble, prime, charge, seat, crimp, finished i will wait till i have several hundred to do batches at a time, i DO NOT do small batches, i do large batches that way i get big lots that are ALL THE SAME. FOR PISTOL - i use a progressive - Dry Tumble, deprime, wet tumble, run thru progressive setup - expand, prime, charge, seat, crimp, finished. Again wait till i have a LOT to do so i have big batches so they are all the same in that lot. Once you have your Dies setup to how you want them, it should be rinse and repeat. Trimming is only after so many firings its to long and needs it. Rifle Brass i keep track of how many firings. pistol i do not. FOR RIFLE - Weighing each bullet - i do this for my match accurate rounds, for bulk loading i do not weigh i just load and go. Hornady did a great video and he said brass length being all the same does NOT matter for accuracy, they did testing on it. Brass - using the same head stamp matters. Crimping - i crimp all rifle and pistol. it helps keep everything uniform and only helps and does not hurt anything All in All - pick what brand equipment you want and learn it, pick the Dies and set them up, pick your bullet, load, and have fun and be safe LOADING IS NOT FAST, TAKE YOUR TIME, BE SAFE, hurrying only creates misteps, mistakes and problems, and you will get hurt! TAKE YOUR TIME, PAY ATTENTION

Personally I appreciate these kind of videos to remind me that no matter what I'm thinking I cannot afford to get into reloading to support the way I shoot. Thank you for your honesty guys.

The plus side to reloading... especially 308. You can tailor your round to what you're doing or hunting for and change things around as long as you keep notes and repeat, repeat, repeat. Bear defence to coyotes to edible hunts. Factory ammo is for one thing.

Tucker was spot on about setting up the resizer die to minimize over working your brass but at the end of his explanation he called it the seater which im sure he meant resizer die, seater die is for bullet seating ,

I am currently working up a load for my daughter to use on her first deer hunt. I like that ammo can be custom tuned to meet performance metrics that may not be offered by factory ammo.

I've been loading my own for years. I don't shoot competition I just love doing it for fun.

Ok ready for the 10 minute talk, have a case of beer and hoping it's enough!!!

I now use to tumblers. First has Franklin Arsenal media. Does a great job. But plugs up the flash holes. After I size I throw brass in my second tumbler that has fine walnut media and some polish. Does not plug the flash hole.

Excellent talk.

Great show on reloading you can always learn something new one thing I would suggest for us people who use single-stage presses make sure you dedicate your shell holder to your die because they very in thicknesses

What would you consider as one of the most important aspects of reloading, is it Good Brass prep ?(Resizing, cleaning, trimming, annealing etc..) , Consistent powder charges? Consistent neck tension? Or is it all of the above?

Could we see a 10 minute talk on the pros and cons of copper bullets?

Great video! Thought I was pretty good until I heard this. I have a lot to learn.

Get the Things You Really Want. Jumped from the Sparc 2 right to the UH-1. Loving it.

Erik Cortina did a test on annealing by time, go check it out. When you think you hurt the brass... you didn't.

No cats were harmed during the recording of this Podcast.

Great info and tips! Got into reloading because Mark I believe bigger is better and I "just hunt" Wisconsin whitetails with a 30-378 Weatherby. Definitely cut down on cost of dropping the hammer on the stand cannon.

Great podcast. I need to get loading up some 7mm-08. (7mm is the best mm)😂

one question: what do you do when you initial jump to lands doesn't work? if 0,003 increments is too little, what is the "right" answer

I’m longing for the day we get a 10 minute talk on the 7.5x54 French MAS . 🙏

Okay, let’s say I’m a beginner and I just skinned my first cat. How do I know if it will blow my oven up before I put in in the oven?

1:14:00 Runnout has been fairly well proven to not matter at all by multiple reliable sources at this point, including at least one 1,000yrd bench rest shooter. In the absence of the bullet being cocked 45 degrees off to the side, concentricity SEEMS like it should matter, but not 1 single person has been able to prove that it DOES matter, and anyone who has tried, ended up showing that it doesn't matter. Play with it if you want, but the overwhelming data shows that it's a waste of time and money to mess with runnout.

Throw the pins out and find media called "southern shine".

Shoulder neck bushing FL sizing dies is the way

so i know this is off topic but when is the AMG 1 - 10 LVPO going to be available to us plebs

What about match dies vs standard dies?

Jeeeeezus the vocal fry on Scott is something else. Hard to get through that

Comment.... 😊

👍🏻👍🏻

Everytime I hear someone say "neck tension" I think of Kyle from primal rights who explains just how wrong that term is as used colloquially in reloading. The size of the expander ball/mandrel does not necessarily correlate to the release pressure. kzfaq.info/get/bejne/br97rNqWsM3Ve2w.html

Scottwakes up on the morning of a pod cast appearance with a devil on one shoulder and an angel on the other. Devil says fire up the comment section. Angel says tell the truth. Scott says but they're the same thing with a demonic laugh

Oo big word used correctly, another point.

It's not the dog you need to worry about😮

Reloading topic with no Ryan?!?