*Great solar **Generater.Systems** ! Was bought for camping and to use for a cpap machine! Worked perfectly!!*

A welder generator for the hobbyist is a no brainer . Best of both worlds for the extra money . 7018 3/32 is nicer for going around small diameters like that on the pin . Not a big fan of welding pipe on like that . Flat bar brackets on side with holes for pipe thru then fillet weld around both sides . Easier and no chance of pipe wall cracking or tear out . You did a great job though 👍👍

So back in my highschool days we used to do welding on everything in the community for class. built bumpers, trailers, etc. We had a boy welding some round on for ramps, very much like what you did with your tube on round stock approach.... only he forgot to slide the ramp outer tube onto the round before welding up the ends. Took him a good while to figure out why we were all laughing at him. Oh, the good ole' days. I never never woulda made a boilermaker, but you get an A from me on the job!

You did a great job. That welder looks excellent!

It's that time again. time for that one year review on a welder, how's it holding up? What problems does it have? What do you like about it? What it can do and cannot do? What do you wish it had or didn't have? And anything else you think is important. Keep up the great videos!

Wow Tony, that welding is a handy skill to have. I have a stick welder and I know exactly what an amateur weld looks like. Your welds look professional beside my booger welds. Awesome job on your ramps.

💥 That looks like a very nice welder. I’ve been wanting to get back into welding for a long time. It’s a been about 20 years. Hope I can remember how. *Keep on tractoring!* 👍

Looks good. just a suggestion u might want to cut the bottom of the raps at an angle and weld a flat plate on them so u won't dig into the ground or asphalt roads when u off load

Great video Tony -- thank you for taking the time to post this. Helps me as someone in the process of learning. Nice job with your preps and welds.

I love those new ramps You're building they should last a long time and provide lots of loyal service keep up the good work I'm proud of you oh yes tell Hank I said hello

Excellent job on those ramps, and your welds too. Looks better than my welds that’s for sure. Keep up the great work sir

Now that's some ramp! They will hold up! Very good job Tony! I like how they came out! Have a good one! See ya!

Good morning Sir 😊👍 You did an Outstanding field welding trailer ramp repair/building Sir 💪👍😊 You are very well set up and that field welder/generator is great for sure 👌🧐👍 Have a great week Sir and I can see that your wife had fun with the tractor too 💪👍😉 Cheers 🍻

Nice build. I have the harbor freight Migmax 215 and I love it. Sold an old Lincoln welder to buy it. Your new welder looks to be a good machine. HF has some darn nice welders at a fantastic price point.

Nice to see a regular guy doing it yourself. Wish I took up welding for my small engine hobby @ 66yr. old who knows??

Nice video and good job. It's always satisfying to do a job yourself. This video help me get an idea of getting a generator. Thanks

Hi Tony, That was fun to watch. I want to learn to weld now that I have property, tractors and starting to get some tools. Harbor Freight has been my friend so far. I will have to check that Vulcan Outlaw out.

Thank you for the video. You just helped make a decision. Will be buying this in the future for a welding trailer build I'm doing. I can't seem to find a trailer that is built the way that I like them. So therefore I'm building one from scratch

Looks like a very practical unit, and really enjoyed your video editing style. Easy on the eyes AND ears! Not that it matters that much, but curious how loud the generator is. I assume it is about the same as my Champion Chinese Noisemaker, but having a welder attached seems extremely practical. Good thing the grass is green out there! In California, half the state would be on fire by now! Thanks!

I know nothing about welding Tony, but the setup looks capable and the job looks stout. Good point about using the genny for domestic supply in a bind.

Good job. About that pipe. You did fine. I might have used a piece of 3/8 filler rod, or no 3 or 4 rebar, where I welded the pipe to the trailer if I was building for a customer but that's not a big deal. It wiMiller's. It sounds like you are impressed with the welder. I am thinking about buying one as backup for our Miller Bobcat 230. Right now we have two trucks and one welder, which is most unhandy. But we do not need two Millers.

Good job and machine 👍 look very strong creation , merci du partage 🤗🧑‍🏭

You did a nice job

I'm not very good at welding....but I can solder pipe with the best of 'em! 😎 Good work Tony! 👍👍

That’s a nice gen/welder wow I’d love to have that thanks for sharing buddy

Great job! Nothing to be embarrassed about.

Good Job! and great Idea with the tubes for the hinges. I had a 18' trailer with the ramps you had to take off and stow underneath and that got old fast... and they are not light. I bet you really appreciate the swing up ramps now. That Harbor freight welder/geny looks like a winner..

Thank yoi Mr. TONY, very helpful video

We looked at this welder at harbor freight this past weekend, not to shabby, decent quality but a little too pricey for my taste.

Came here from HF to leave a thumbs up!

You did good

Nice upgrade. I invested in a gen 3 Prius CVT to use the motor generators (MG1 and MG2) for a engine welder/plasma cutter/alternator (generator) on a garden tractor platform using an opposed twin B&S 18HP since that's the engine they used on their hybrid car and I might use both MG's to make a hybrid design eventually is the plan. In the queue and slowly moving forward on. Neat seeing HF having as I was just looking to see what the latest and greatest projects are. Will see if I can move forward with my project this winter. Still need to design, fabricate and setup my testing fixtures first and foremost since there's not much data on those MG's though some can be deduced/infered. Thanks for sharing!

Awesome. Great video.

Cool. Thanks man...

Nice job! Similar to how I hinged my ramps.

Nice video man loved everything about it

I need this welder

don't be afraid to use bigger rod=3/16th 6011 + 5/32 7018----run 6011 3/16 slightly cool on gaps , just linger in a circle a little bit to let it heat and deposit before cruising into the gap or bevel otherwise it will seem way too cold

Awesome job, I always heard only 1% of the world population can weld, such a personal pleasure to be able to fab, that dog will hunt!

other than a few gussets on the hinge pipe i say it's perfect.

Thanks Again Great Video For Me

My friend I'm about to have to reup my HF membership lol. I have two Lincoln welders but I don't have a gen/welder. On the pipe hinge of the ramps I would add a gusset or two on the bottom side and maybe a a way to add flat strap metal to hold the ramps up in transport

I would have made the C channel on the sides a lot longer past the other piece that boxes the end and coped. You would have the top of the pipe flush with the outside of the top of the C channel that way you could weld the ends as well, I would also put a weld in the middle. If that don't hold nothing will.

Great video did you build support legs for your ramps that will help you out with loading up and unloading. It will also keep the trailer from picking up on the back of the truck when the tractor is backing off and on.

Subbed. Great attitude and advice.👍💪🇺🇸🙏🏼

I'd go with a thicker pipe sir . That one will eventually rip off . But those ramps look great .

I enjoyed your video. Your commentary style is great and i love how you say "ittt'll hoed." Reminds me of moving to Georgia in 10th grade and the english teacher said "class turn-own page 200 of Alas Babalon." And then the suburbs of Atlanta lost that rural Georgia accent. Impressive welder generator whats it run on $ ? Their quality over at harbor freight is getting better snd better, now nobody can bitch, its good stuff.

I have a question you think I could knock out a pipe fence with this welder. And how’s the duty cycle I noticed you didint have any problems at all.

Nice job. Can you tell us the material list and dimensions for your ramps. I also own the HF high end bandsaw. Now that's a combination with super clean cuts. Haven't even bothered to use the coolant tank with mine. Stopped using my Dewalt 14" carbide tipped multi cutter slow speed chop saw. Great job. Looking forward to a materials list. And possibly a cut list. Thanks

Tony, that was a great job and inspirational. What is the least expensive welding unit one would require to handle a task comparable to Tony's effort?

I came for a review of the welder, awesome job by the way! But I would like to know what little welding table is that? Is it custom?

How's the welder holding up I'm thinking of pulling the trigger on one of these

When I weld 7018 on pipe I always weld about 125amps DC and go uphill

I’ve got a brand new Vulcan 195 outlaw. I followed set up for welding. The only way I can get it to weld is turn on the on/off welding switch and also the 2pole breaker under the snap lid. The engine revs up like it has a load and will not idle down after you stop welding. I’m sure that’s not normal because all other gasoline welders idle back down when not welding. Am I missing something. I have went over the directions several times and it doesn’t say to turn on the 2pole 30amp breaker before you weld. Please help

You didn't see need for legs on your ramps? That is a very good good job on the build. I don't think you are an amateur welder either.

Great job Tony. May I ask why you don't replace that floor board on the dove tail. Just curious. Always enjoy your videos. Thanks for sharing. Iowa cares :)

Do you don’t have to hook up the panel ground?

What are your thoughts on how loud the unit is? I see the main body isn't covered or insulated. Just curious if it could be quieted down? Also any issues with the duty cycle on it? Did you ever need to give it cool down time?

Will this run a 5/32 7018?

Does it run 6010?

I need help with purchasing correct size generator for my welder but nothing over the top ,, tia Hobart Stickmate 160i It can run off 110,115,120v or 220,230,240v input power , •120v = 20-80amps (65amps @20%) •240v = 20-160amps (160amps @30%) •Minimum generator power required = 2500watts •Minimum welding amps = 20amps •Maximum welding amps = 160amps ,

I just got this welder and set it up. It seems that the auxiliary power switch needs to be in the on position to operate the welder . Is that correct ? I didn't find anything in the operating instructions about it. Thanks

I have the vulcan commander 225 SMAW machine and the SOB wont run 6010 at all... does thst generator run 6010?????

When are they gonna restock

I really want to purchase this welder do you think it’s a better buy than the Hobart champion 145 ?

The hobart champion 145 is alot smaller and lighter but less amps

How has it held up

I’ve been waiting on that welder for a while when did Vulcan debut that welder generator?

I just want to know if its worth it for such a high price tag

Can that welder do tig

Any updates ??

Does it come with higher altitude jet?

I think the Lincoln welder very similar selling for maybe $60. , more.

Price??

What do you do if you need parts for that thing. Just hope it doesn’t break?

Can you weld and power tools at the same time?

YOUNG MAN , I M RETIRED , I ENJOY WELDING , I BUILD HEAVY DUTY WELDER CART AND 1/4 " ANGLE IRON STEEL RAMP , THE RING WAY AN MY WAY / MY POINT ARE UP /NOT UP SIDE DOWN RAMP MOST WELDER MAKE OR WRONG WAY TO BUILD STEEL RAMPS

Ac machine?

Update

bring back the 25% coupon or any vi va la coupon

being the cheap lazy A$$ I am I would of just turn the ramp over. ;) Looks like a decent job!

Geinder makes what the welder aint my man. Not too bad. Seen worse pass through inspection.

Don't you wish you could actually move that fast....

Why pay $2000 for harbor freight when you can get a used Lincoln or Miller for the same price?

Tony do you remember a subscriber you had last year that liked to tease Hank about wasp nests red wasp and yellow jackets That subscriber went by the name Dear anil. I changed smartphones I also changed smartphone programming that used to be me now you see my true name I finally bought a decent phone Worthy of my prestige I got rid of those cheap $49 Walmart phones and bought a Motorola from the factory $250 dollars this phone has impressed me it even has special recognition and the talking Google Assistant I no longer have the assistant this phone has is Alexa I am still trying to learn the rocket science of this new smartphone tell Hank I said hello Sincerely Robert Winton