vulcanised mold

Рет қаралды 126,684

soham harrison

11 жыл бұрын

quick way to make a vulcanised mold

Пікірлер: 53

@thegaryjay_yt 5 жыл бұрын

Thank you, Soham. I love watching process videos. You did great!

@dbaider9467 6 жыл бұрын

Alright, here I've been using scalpels for years....This is a genius way to part the sides. A big thank you. Brilliant.

@silentscribes 8 жыл бұрын

you are so good at teaching, thank you so much

@briantunzi2462 8 жыл бұрын

Well Done an THANKS ! for not trying to be a DJ at the same time !

@fakharshehzad5829 6 жыл бұрын

Brian Tunzi i

@sarap979 Жыл бұрын

Thank you so much!! Great video!

@BuDWiskey 9 жыл бұрын

Very good video - thank you sharing your process - I'm trying to get familiar with the process so I can minimize using up my rubber on errors and mistakes. Really like the Talc for helping with the parting. Thx

@whichcraftartstudios 7 жыл бұрын

Where's part two and three? I would love to see the rest of the project. Especially with you as the teacher.

@orwad7916 7 жыл бұрын

Excellent video

@mbnick_ 6 жыл бұрын

This helped!!!!! Thank you!!!!

@VNMFTW 9 жыл бұрын

thanks so much for sharing! Appreciated more than you know.

@kavithabalakrishnan8653 11 жыл бұрын

Thank you. Very beautiful.

@shlpl420 9 жыл бұрын

Thank you very helpful!

@silvernail8989 4 жыл бұрын

Thanks for the video...very helpful. Take care

@jorgenava1726 2 ай бұрын

La separacion de las partes se logra mas facilmente si se usa un poco de talco sobre la primera parte,sin tocar la pieza a reproduccir. El molde vulcanizado de hule,se serge en petroleo durante 24 horas el molde se hincha y puede aumentar de tamaño asta un 300,por ciento,con cera de parafina,se puede obtener una figura igual,pero mucho mas grande copia fiel y barata.

@patprop74 4 ай бұрын

I think it was a great approach to lost wax casting for its time, Fast forward to 2024 with crazy affordable 3d resin printers that can print with wax resin, it makes this a dying artform sadly. but these are the fundamentals that should never be forgotten

@ryanspackman548 7 жыл бұрын

Would this work for hollow objects--or would the pressure break the master? My interest is in a basic LEGO brick which is hollow in the middle and bottom.

@ravebiscuits8721 6 жыл бұрын

How hot could you cast using this mould method? I'm thinking about casting with pewter or lead. And I know this is going to sound awfully cheap of me but would it not be possible to use just a clamp and an oven for this?

@MrGuerrero73 4 жыл бұрын

Hi!I have a question.Can you use this method on a Pink rubber?Thanks. wonderful video!!

@hydriarief9261 11 жыл бұрын

thank u verymuch your video.. very helpfully,

@ruigonzaga1363 3 жыл бұрын

Obrigado por compartilhar seu conhecimento. :-)

@kennedy67951 9 жыл бұрын

Hey would you tell me what the name and type of tabletop vulcanized machine you have? PLEASE.

@csmart287 8 жыл бұрын

Thanks.

@bobbauvian7700 Жыл бұрын

thank you so much, have a question, is the temp in C or F. I am assuming it is in C

@gianpaoloabagnale2564 6 жыл бұрын

Hi, but is this your car made in craftsmanship?

@gktrand 4 жыл бұрын

Thanks

@therestorationofdrwho1865 6 жыл бұрын

I have a rubber part that over time has started unvulcanizing itself. Is there a way to revulcanize it? Thanks

@1soham1 6 жыл бұрын

not to my knowledge. perhaps google

@therestorationofdrwho1865 6 жыл бұрын

soham harrison Do you know how I would go about getting the part remade? It looks like there are not reproductions so it'd have to be from the one I have.

@1soham1 6 жыл бұрын

you have to make a new mold from one of the previous castings

@therestorationofdrwho1865 6 жыл бұрын

soham harrison So, how would I make a mold from my casting? It’s old but mostly in tact.

@1soham1 6 жыл бұрын

inject wax, cast it and make a new mold

@rubenvalencia8120 6 жыл бұрын

excelente video felicidades

@1soham1 6 жыл бұрын

gracias

@kamleshsingh9501 7 жыл бұрын

nice cutting to rubber mould

@robertdistefano6895 9 жыл бұрын

i've had a concave tree branch vulcanized and it came out broken. any suggestions how to mold fragile objects?

@1soham1 9 жыл бұрын

2 part liquid silicone works well for this

@ericjurgens372 9 жыл бұрын

soham harrison not if you plan on pouring molten metal into it...

@ezridaeus 9 жыл бұрын

Eric Jurgens Works fine for wax injection.

@haidafella8651 7 жыл бұрын

vulcanized rubber is more heat resistant than silicon? i'm no authority on it, tho i have poured pewter into some of my two part silicon molds before, with fine results, i just did it cos i was showing some kids some stuff about carving and molds.. but the logic in me says that if it was heat cured then, introducing heat into the equation would not be good for the mold.. maybe it;s just not enough heat to matter

@dbaider9467 6 жыл бұрын

No, no, this is all for lost wax casting in investment. (Google) :)