Me knowing nothing about engines , now feels more confident , thanks to the master explanation. ❤DTE TV
@YTDTETV Жыл бұрын
Always do my best to help people out 👍
@harrisondavid8607 Жыл бұрын
Had this issue on our taxi fleet. The debris looks like old paper gaskets breaking down, but there are none on the engine like that. Oil and filters changed every 10,000. No signs of oil filters breaking up either. I did suspect the oil supplied by the gaffer though. Low SAPS oil is essential. Great video, and the tip on the 5mm ball end is spot on. Quite a rewarding job once you've done a few.
@YTDTETV Жыл бұрын
Hey bud thank you 👍 surprising what sometimes ends up in the sump, appreciate the kind words 🙏
@neilhampson2843 Жыл бұрын
You have to blame VW for this,there oil change intervals are stupid. And it's not just VW as most manufacturers are the same. I had a Audi A6 2.5 tdi V6 and the oil change interval was 24000 miles (are they nuts). I change the oil every 6000 with mobile 1 which I know is a bit extreme, but it's a lot cheaper than a new engine. Great information and good to see your engine is in good nick.
@YTDTETV Жыл бұрын
Hey Neil wow that is a long time between services, I know some other manufacturers have 20k between services. That’s so bad and it’s bound to cause problems for higher mileage engines. I have a customer that has a service every 6k and he’s never had a car break down 👍 thank you for your comments.
@neilhampson2843 Жыл бұрын
@@YTDTETV Thanks for the response. The Audi I owned went through a full set of cam followers and a turbo at 65000 miles due to the stupid long life oil changes. It does not affect the owners that buy them new, it's the poor bugger down line gets all the headache.
@YTDTETV Жыл бұрын
@@neilhampson2843 no worries 👍 that’s right the first owner gets hassle free motoring it’s the later owners that have to suffer the consequences unfortunately. Vauxhall have a service interval of 20k to and the engine doesn’t even have 3.5lt of oil, that’s so bad.
@MalteseMafia Жыл бұрын
Good advice on filter changes 👍 2 videos in a week you are spoiling us. 🤣 I think 10000 miles is about right 👍 good advice on fitting the sump, fitting it square using all the bolt's.
@YTDTETV Жыл бұрын
Hey Philip it makes such a big difference with oil changes, I’ve seen so many cars well over due a service and all the owner says is it necessary as its running fine. It’s those people that slag their vehicle off when it breaks saying poxy car has let me down. The 2 tricky bolts are easy to go in wonky so just my little trick. Yep 2 videos this week really aiming to just make videos full time so hopefully the extra effort pays off. Thank you sir 👍
@jamesbarran-scott437 Жыл бұрын
@@YTDTETV I’ve had that, had a friend that was working a Ford main dealer service desk, had a whole family in kicking off that their 4 year old car with 70k miles on it needed a turbo… when he pointed out that they’d never had the oil changed and maybe that was a factor in the turbos demise they where genuinely shocked… 🤦♂️
@christinamacintyre99729 ай бұрын
Love a guy who takes his own motor apart so he can see the difference
@brauliobethancourt897910 ай бұрын
Strait up to the point no mingleling, thanks bro have a great day.
@YTDTETV10 ай бұрын
Hey bud thank you appreciate that 👍
@karl3927 Жыл бұрын
Thank you for the video. Top diagnostic skills to the fore there. Totally agree with you about the necessity of regular oil and filter changes. It's a false economy not to do it. That owner was a lucky bunny not to have toasted the engine. Keep up the good work and Merry Christmas to you.
@YTDTETV Жыл бұрын
Hey Karl thank you mate merry Christmas to you to 👍, I have a customer that gets his oil and filter done regularly and he’s never had a problem. Some manufacturers say up to 20k before a service and I’ve seen a lot of them break down.
@alanhowarth1898 Жыл бұрын
Love your videos mate keep them coming hope you and your family has a lovely Christmas 🎄
@YTDTETV Жыл бұрын
Thank you Alan really appreciate that, merry Christmas to you and the family to 👍👍
@omarh.230 Жыл бұрын
Thank you! This is the best troubleshooting video ive seen about this issue! Iv been going crazy tryin to fix my 2013 passat tdi.
@YTDTETV Жыл бұрын
Hey bud glad the video is useful, do the oil - oil filter first as well as the oil pressure switch, see how it is and keep me updated 👍
@titorojas33311 ай бұрын
Last week I added the engine flush moly liquid addictive for diesels engines and when I started it up it ran rough and the low oil pressure show on my dashboard. Funny thing is I always replace my engine oil every 7500 miles cause I want my Mk6 Golf TDI to last me longer. Looks like I will have to remove the oil pan and inspect it and clean it! Thanks for the amazing video! 9/23/2023 update: oil pick up looked clean and unclogged. Oil pan looked clean! So the initial star rough idling could probably be something else, H’mmmm what could it be? Definitely need to do some extra work!
@YTDTETV11 ай бұрын
Hey bud glad your pickup pipe and sump was clean 👍 I’d try a fuel filter for rough running 👍
@sats7819 Жыл бұрын
Top stuff mate.. My cayc engine has no boost. Changed EVERYTHING.
@YTDTETV Жыл бұрын
Hey bud thank you appreciate that, when you start the engine the sending it fires up does the actuator on the turbo move? Might need someone to start it while your looking at the actuator.
@peterfox6256 Жыл бұрын
Carbon in the oil is sometimes the injectors blowing past the copper washers into the engine
@YTDTETV Жыл бұрын
Hey Peter I did wonder if this was the case 👍 I definitely believe the extra heat and pressure from dpf filters are a massive cause of this.
@mick7425 Жыл бұрын
Brilliant video as always and love your van too. That colour makes it pop.
@YTDTETV Жыл бұрын
Hey mick thank you mate 👍 I’m really happy with the van I’ve done nearly 2k miles since fitting the new turbo. Merry Christmas bud 👍
@mick7425 Жыл бұрын
It's lasting well then,happy Christmas to you to m8 and family
@alfredohernandez112420 күн бұрын
In the passat you have to turn the flight wheel to the notch and u can remove those bolts with the 10 mm socket straight
@CharlieStagg59Mx7 ай бұрын
Awsome vid will be doing this to my polo in the next few days which has pressure problems. This is next on the list
@YTDTETV7 ай бұрын
Hey Charlie thank you hopefully it helps with your issue 👍
@mrwhite292 Жыл бұрын
Yep excellent job again, keep up the good work & video’s really enjoy watching! Take care, peace 👍✌
@YTDTETV Жыл бұрын
Thank you Simon you know I always appreciate your comments 👍👍
@ChrisJohnson-gp9vt Жыл бұрын
i always check the drive pins aswell while its off changed prob near 50 of them with oil pumps for rounding off , good vids again 👍
@YTDTETV Жыл бұрын
Hey bud, I always believed it was just the balance shaft BKD’s that has the oil pump issue I’ve not seen one go on the engines without the balance shaft but I’m open to learning 👍👍
@sollykhan2385 Жыл бұрын
TOP GEEZER, Thank you for posting this awesome video, really helped,as i had a passat 3C with identical problem, keep up the great work, Bless 🙂😇
@nigelswann2873 Жыл бұрын
Another great informative vid Nathan, think I'm going to do mine now as when I serviced it the filter are in a bad way and my turbo whistles and small bit of blue smoke.
@YTDTETV Жыл бұрын
Hey thank you Nigel, the oil filter in this one was sucked in as I describe it but so was the one on the caddy BKD but clean sump. A lot of Vauxhalls really suffer with sucked in oil filters and being starved. Little bit of blue smoke isn’t the end of the world as the intercooler and pipes get oil in them from weeping turbos but that’s normal.
@barrygray8356 Жыл бұрын
Same problem with the Insignia B20dth and A20dth. Continue to drive with low oil pressure warning and your engine is completely knackered. To change the oil pick up pump and seal on these motor is a nightmare, the sump is very hard to remove esp the side of the gearbox bell housing... Some drill a hole to the bell housing to access the bolts
@YTDTETV Жыл бұрын
That doesn’t sound like the easiest of jobs, lucky on the vw’s it’s really easy access. A lot of cars suffer with carbon build up especially since dpf’s have come along.
@karter5351 Жыл бұрын
You cleaned that sump up nice DT, don't think they would get it that clean down the main dealers. Agree with regular oil and filter changes, 10,000 mile max for me, have a great Christmas
@YTDTETV Жыл бұрын
Thanks Karter, yes you could use all the flushes you like but a sump removal and clean up definitely does a better job. Some manufacturers say up to 20k before serving which is so bad. Merry Christmas to you sir 👍👍
@edogsx Жыл бұрын
Diesel makes the oil dirty... to avoid these problems just change the engine oil every 5/6000 km and maybe use a flush to run in the engine 10 minutes before draining the old oil. I had several analyzes done by an engine oil laboratory and after 5000 km the contaminants in the oil are already at the limit of tolerance, especially in direct injection turbo engines.
@YTDTETV Жыл бұрын
Hey bud yes diesel oil is always dirty, I had a customer that had an oil and filter every 6k and he never had an engine break. I never knew why diesels where always dirty but now I do so really appreciate your comment 👍👍
@edogsx Жыл бұрын
@@YTDTETV Diesel contains heavier hydrocarbons than petrol, this fuel is burned by detonation therefore with a higher compression ratio and produces lower temperatures than petrol. the combination of these factors produces a greater quantity of carbon residues and a greater blow-by effect so that the oil gets dirty very quickly. the carbon residues, in addition to having an abrasive effect, increase the quantity of acids, the oxidation of the oil and reduce the quantity of Zinc present in the oil, Zinc together with phosphorus constitute a very important EP additive ZDDP which prevents wear of engine components, especially those made of steel.
@YTDTETV Жыл бұрын
@@edogsx wow I had to read it twice but I got it 👍👍 someone on Facebook said why would a diesel sump have more crap in the sump and dirty oil over a petrol and I wasn’t 100% sure but I replied I think it’s blow by in the cylinder. I also said that it’s more modern diesel engines due to the filters in the exhaust causing excess heat a pressure in the cylinders causing even more blow by. I don’t know if you have a KZfaq channel but I’m going to look now as you certainly know your stuff. Thank you for your comments 👍👍 You do I’m subscribed 😊
@PenitusInferis6 ай бұрын
Very well done and explained, thanks. I had my balancer hex rod slipt off but it was the mechanical who was driving, not sure how long it was driven that way. The guy says the turbo was fried but the engine is ok, which i highly doupt. You say thst you saved the engine.. how to know if the engine is fine? I will go see the balancer rod and all the stuff with my own eyes and im pretty familiar with the steps. The engine is a cbab 2.0tdi. ill appreciate very much u reverting..
@vwtransportersandmotorcycl372911 ай бұрын
Shit man that was bad! I now feel paranoid about my T5, sump might be coming off soon 👀
@YTDTETV11 ай бұрын
Hey bud so it’s all depending on the life of a vehicle so maybe this one didn’t have as many services, it doesn’t take to long the take the sump off so definitely worth a check 👍
@Mac_F87 Жыл бұрын
Only had our Caddy about three weeks now. It’s on 143k miles and the paper work said it’s been serviced regularly. I had the sump off to reseal thinking it was leaking, turns out it as the rocker cover. The sump looked much like yours and was easy cleaned with just a quick blast of brake cleaner. So it would seem it’s been looked after at least, bonus. Gives me confidence the old BLS might not give up too soon. In your opinion is it worth doing the big end bearings? As sort of preventive maintenance in the BLS. Seen a few theories that it’s spun bearings that might cause them to pop one out of the block.
@YTDTETV Жыл бұрын
Hi bud yes they do clog up abit 👍 it’s the big end bearing bolts that let go ie the conrod bolts if I was to trust a BLS engine I’d put arp conrod bolts in and it would last forever 🤙
@Mac_F87 Жыл бұрын
@@YTDTETV top man, nice one bud I’ll look at getting some bolts then. I’ll do the bearings while I’m in there.
@sale199611 ай бұрын
bkd has injectors in oil in valve cover ..blown injector seals can burn oil like that...had similar problem with toyota 1cd ftv
@chuckmcconnell8355 Жыл бұрын
It looks like you work on a lot of volkswagens. I just rebuilt a 2.0 l turbo and my low oil pressure light comes on after about ten minutes of run time I did put a new oil pump in it and cleaned everything when I did the rebuild. If I check the oil pressure with a gauge I get about 15psi at idle and up to 45 psi when revving the engine but I keep getting a low oil pressure warning. I have also replaced the pressure sending unit. I am at a loss.
@YTDTETV Жыл бұрын
Hi bud I do a few vw’s, I would try the wire to the oil pressure switch. If you take the wire off the sensor and connect a piece of wire to it and earth it to the engine somewhere, all the sensor does is create an earth signal so if you do this and the oil pressure still comes on then there’s a break in the wire somewhere. Seen dodgy wires a few times.
@alu636311 ай бұрын
Excellent Info!
@user-fb7or1wt3t Жыл бұрын
Glad to find your vid. I sure hope I'm not going to have to do all that and a simple oil change will do but I'm also a bit scared since my 2.0 touran suddenly won't start and displays red message "low oil pressure - check owners manual". It's a second hand from my brother and my first diesel. He told me it should have run for 5k more until next oil change. Any ideas would be very much appreciated. Thanks!
@YTDTETV Жыл бұрын
Hey bud sorry for the delay, so first of all has it got enough oil in it? They can have non start if oil is low. They do like an oil pressure switch aswel and they are only cheap.
@samrouse3522 ай бұрын
What happened to the golf from this video Nathan? Love the content
@YTDTETV2 ай бұрын
Hi bud I do still have it but it needs a lot of new parts and £££’s
@Formula1-Dave Жыл бұрын
I have this motor ❤️ I need detailed DIY videos even if it takes 1hour I'll watch it.
@YTDTETV Жыл бұрын
Hi bud it did only seem to be one of the BKD engines I looked at so a good oil flush with oil and filter change should clean the pick up pipe without removing the sump.
@Formula1-Dave Жыл бұрын
Thank you
@howiewalker1818 Жыл бұрын
Nice job 👍
@YTDTETV Жыл бұрын
Thanks howie appreciate that mate 👍
@deanminter61 Жыл бұрын
Mine is due for service/MOT in Jan Bro, i know for a fact mine needs tlc on the filters and oil!
@YTDTETV Жыл бұрын
Hey bro I did change yours just before I got it but yes an oil and filter change is alway a good idea 👍
@riosavannah123 Жыл бұрын
Good video , no bullshit
@YTDTETV Жыл бұрын
Hey bud sorry for the delay, thank you appreciate that 👍
@Sheenmeemseen Жыл бұрын
Afternoon brother, 🍿
@YTDTETV Жыл бұрын
Hello sir 👍👍
@MrJorgvankleef Жыл бұрын
Check also your hex drive in oil pump is my advice..........you know what i mean as a 2.0 tdi owner...greets!
@YTDTETV Жыл бұрын
Hi bud the hex drive only breaks in the 2.0tdi engines with the balance shaft it doesn’t fail on these. I had an Audi a4 that it failed so I removed the complete balance shaft and fitted the normal oil pump.
@philmcfadden Жыл бұрын
Good video, thanks for this warning (if I don't like the way someone talks I just mute it and switch on captions, but you're ok with me) - oil light has come on my bkd at about 120,000 miles, I'll do this job tomorrow. I change oil with the best I can get with a new filter at 6000 miles tops. I see a couple of comments about the oil pump in these engines - any pointers as to what I should do? Also, I usually use a thin smear of hylomar blue but it looks as if you've used a thicker sealant? Cheers, Phil
@YTDTETV Жыл бұрын
Hey Phil sorry for the delay, ah man really appreciate the feedback 👍👍 have you done this job? These BKD’s don’t suffer with oil pumps it’s the A4’s and the passats. Yes I use a silicone type sealent for sumps. Let me know if I can help 👍 I’ll reply this time. Thank you
@philmcfadden Жыл бұрын
@@YTDTETV cheers mate - oil pressure gauge reads 5bar☺️. I found a lot of rusty earth connections to chassis behind the left headlamp, cleaned them up & that particular warning disappeared! There are also suddenly a lot of fault codes and the car is running erratically though, so when I get time I'm going to look🤞 more closely at the wiring harness & the ECU connector...
@twes5563 Жыл бұрын
Yes mate spot on service on my b6 2.0 tdi £30 oil and filter all in. And the DPF and turbo whent bang a year ago so I know exactly what your talking about £800 later 😭
@YTDTETV Жыл бұрын
Hey bud yes oil and filter is really cheap yet some people think it’s ok to skip it as the car is running fine. It’s a good idea to have a DPF delete and remap it makes a massive difference on engine longevity. Thank you for your comment 👍
@twes5563 Жыл бұрын
@@YTDTETV yes my car is about 210 bhp with abit of remapping dsg aswell but I'm selling it as want something cheaper
@YTDTETV Жыл бұрын
@@twes5563 very nice I do like an auto 👍
@darranbond3448 Жыл бұрын
nice dobo the man
@YTDTETV Жыл бұрын
Thank you sir appreciate that 👍👍
@malinjones68158 ай бұрын
get low oil pressure on my mk3 1.6 caddy on 226.000 is it roughy the same to do on a 1.6 ,I'm thinking it could be the oil pick up after watching this very helpful video ,I've also got another issue with it filling up with desil around the injectors ,the injectors seem fine the van starts well and pulls well so I'm thinking its the return pipes leaking if not any ideas what I could do without taking injectors out I was thinking they might not have changed the injector seals when the injectors were done
@charliemetcalfe6753 Жыл бұрын
Hi mate, love the vids. I've got a BKD Jetta with a little issue, when rolling in neutral (clutch up) at very low speed, like coming to a stop for example, the engine misfires harshly and shakes the whole car. When I come fully to a stop it completely goes. If I'm in gear or the clutch is pressed down it runs perfectly... am i right in thinking flywheel? You seem like a very knowledgeable guy with these PD engines so thought you were the guy to ask. Cheers
@YTDTETV Жыл бұрын
Hi Charlie thank you mate appreciate that 👍👍, so when your slowing down and clutch up it’s misfiring then as you stop and depress the clutch it straightens up? If so first thing I reckon would be to look at the crank sensor, reason is when you press the clutch down it will ever so slightly move the crank and flywheel towards the sensor then as you let off it will move away slightly. That’s a pure stab in the dark without seeing it, does it have any fault codes stored?
@charliemetcalfe6753 Жыл бұрын
@@YTDTETV Hi, thanks for the response. If I’m stopped with clutch up (idle) it’s fine, if I’m rolling with clutch down it’s fine. It’s only if I’m rolling when the clutch is up in neutral (coasting). No faults stored and have logged the injectors as I know BKD’s are common for injector loom issues and all seems fine. Apart from this it drives impeccably.
@charliemetcalfe6753 Жыл бұрын
@@YTDTETV actually another thing that may be worth noting is that when starting sometimes it throws the whole car about with the rocking of the engine. Doesn’t really struggle at all but you really feel it.
@YTDTETV Жыл бұрын
@@charliemetcalfe6753 no worries happy to help, it is possible that the injector loom is playing up as any movement causes the same issue. If you work it out let me know 👍
@charliemetcalfe6753 Жыл бұрын
@@YTDTETV thanks mate, only thing that put me off that idea was the difference when the clutch is down. It’s
@Ventorii2 күн бұрын
1.6 tdi Cayc engine, i got problem with low oil pressure. New oil pump, cleaned pickup pipe, fresh oil and filters. My mechanic says only 0.5 bar at idle and around 1 bar at 2000rmp (75 celc temp) which is still not enough. What to check next?
@richardp42925 ай бұрын
One turbo died because of oil starvation. Possible cause? Will find out tomorrow. Have you got a list of the cleaning fluids you used and the mastic?
@zactwentythree Жыл бұрын
Great video and tips thanks! I’ve got the same 2.0 bkd, I’ve just cleaned egr, inlet manifold and changed oil and filter. Now I’m getting the “oil pressure engine off’ warning I’ve already had the sump off and it was all clean also changed the pressure sensor, any ideas? I’m hat to try next?
@YTDTETV Жыл бұрын
Hi bud sorry for the delay check the wiring to the pressure switch as I’ve seen these fail loads 👍 it should be earth so you can try earthing the wire to see if the light goes out then you’ll know if it’s that.
@zactwentythree Жыл бұрын
Thanks for the reply DT! It was the oil pressure switch plug not pushed on enough as the new sensor wasn’t original vw so I removed a little rubber grommet from the plug which allowed it push on more! She’s running a treat again with decent mpg! Cheers 👍🏼
@gwl786 ай бұрын
My mate has this low oil pressure problem on his 2008 tiguain
@alanmann9 ай бұрын
quick one - I've got a VW TDI (B7 CFFB) and just replaced the turbo (107,000 miles) old one was burning oil. But new one is dripping oil from the exhaust side turbo seals. Return feed is clear, I checked all pipes before the refit. Is a block somewhere causing excess pressure in the sump? What things should I check? I'm handy with the tools, just would rather get a few ideas before throwing away this otherwise great car (VW CC 2012)
@YTDTETV8 ай бұрын
Hi bud it may take a fair few miles to clear all the old oil out after fitting a new turbo, sometimes up to 50 miles.
@dyl5518 Жыл бұрын
👍👍👍👍
@YTDTETV Жыл бұрын
Thanks mate 👍
@telstraa0982 ай бұрын
Hey man I am doing the same for vw amarok 2014 oil pressure light...just wondering how to remove front member crossing look like it's welded...I want to get more access...but now very less space mate
@alkader683 ай бұрын
How to replace the oil pressure sensor on a 2013 Volkswagen Touran Diesel TDI
@chrissmith40835 ай бұрын
Hi have a Volkswagen crafter Luton kids coming up with intermittently low oil pressure switch off engine when you switch off disappears and then it will come on again later that day. Just had a new turbo fitted. Any advice as the garage is going round in circles
@arnoldkul3827 Жыл бұрын
Hey mate good video. What specific oil do you put in the PD lump's?
@YTDTETV Жыл бұрын
Hi bud thank you, the pd engine actually has its own 5w40 pd oil but I’ve used normal 5w30 many times with no issue 👍
@cade270 Жыл бұрын
Had low oil pressure warning on my vaux zafira tourer 2.0 cdti turned out to be pick up seal failure common problem £700 to drop sump and replace ... ouch
@YTDTETV Жыл бұрын
Hey Pete I’ve not delved into to Vauxhalls much, ouch that’s a few quid 👍
@bobbondarul7448 Жыл бұрын
Nice What is the shaft screw tightening torque? Your Caddy has a oil pump belt ? Thank you
@YTDTETV Жыл бұрын
Hey bob I don’t normally use a torque wrench unless I’m doing something super important, I think the oil pump has a small chain coming from the crankshaft.
@bobbondarul7448 Жыл бұрын
@@YTDTETV Mine is 1.6 tdi CR 2012 and the oil pump is belt driven I'm interested in shaft screw tightening torque the one that is removed with 19 socket.
@user-fb8gw6wu7y4 ай бұрын
This the same for Seat Leon 2.0 pd150 2006. Mrs just cracked the sump 🫠
@YTDTETV3 ай бұрын
Yes mate 👍
@damiand7425 Жыл бұрын
Should check bearings while sump of
@YTDTETV Жыл бұрын
You are right Damian 👍
@danielfoxall13804 ай бұрын
I keep having this problem with my ibiza 1.6tdi 3rd time in a year it been resaly looked after service ontime or before needing it any ideas why it keeps happening? Thank you if you get back to me
@juaniemanful11 ай бұрын
Hey bud i have a 2.0 tdi Amarok with a flashing red oil light, I've changed the oil all looks good, switch has also been replaced but still have the blinking oil light. Someone mentioned it might be the oil pump thats on its way out. Where should i start,
@YTDTETV11 ай бұрын
Sorry for delay just double check the wiring to the oil pressure switch as sometimes the ends corrode and have a weak connection 👍
@juaniemanful11 ай бұрын
@@YTDTETV thank you for your feedback. I have relaced the oil pump recently. I have tried grounding the switch itself to the head of the engine and the wiring is still perfect. But i still have the persistence of the oil light. There's no definite reason or proof that i can see that something is causing it.
@user-hc4md8vq6b6 ай бұрын
I have a 2016 t6 vw caravelle. It has low pressure but I've changed the oil pump and pressure sensor, oil cooler housing, tested the oil cooler and the test was fine. The pressure reduces when the engine is hot. Please help
@thatginettaguy17142 ай бұрын
Did you fix this? Interested to know what it was?
@dOObie_da_dondada7 ай бұрын
Hello there I have a 2010 cc 2.0 I have low oil pressure warning it's misfiring and klunking when I accelerate. The oil pan is covered in carbon i changed the coils and plugs and the pcv valve 113,000 miles do you think it's the same problem? Thank you
@davidhorwood60753 ай бұрын
Did you find out what went wrong? I have possibly a similar situation
@ashleyjones1976 Жыл бұрын
i also got bkd engine the low oil pressure flashes up when the engine cranks over for 30 sec but i will be taking the sump off to cleaning it. i bought it as a none runner but this time last year the turbo went bang as i was driving home a lot of white smoke thought lol do you know of any other common faults ?
@YTDTETV Жыл бұрын
Hey Ashley 👍 I’ve blown a few turbos on these and they smoke a little for a while after till it’s all cleared out, I know that some of the early BKDs have a porous head so leak water but I have 2 early ones and never had a problem 👍
@Kristiqn7775 ай бұрын
Hello❤, I got today this message Oil Preassure Engine Off i drive VW Golf 5 2005 BKD. I need to clear or maybe need to changed Oil pump????😊
@YTDTETV5 ай бұрын
Hi 👍 I would first change oil and filter, then the oil pressure switch and lastly whip the sump off and check inside the pickup pipe. I think the oil pump will be ok.
@BarryBrowne-ln8bn Жыл бұрын
Hello there mate. I have a 2.0 2016 crafter and the oil pressure warning has come on. Would this be the same issue. Baz
@YTDTETV Жыл бұрын
Hi baz.. your engine is the common rail engine so a little different. First thing I would try is oil pressure switch - oil & filter. The pressure switch is on the right hand side of the block just round the back little bit hard to see but it’s there. Try those first run for a minute and if it’s doesn’t fix then take the sump off 👍
@andreasbergeland7467 Жыл бұрын
Hi! Do you know if the transporter T5.1 have a belt or a chain for the pump?
@YTDTETV Жыл бұрын
Hi bud sorry for the delay I think it’s a chain but not 100% sure, thanks
@loudonnelly2591 Жыл бұрын
Hi mate. Did this cause a slow start on it? Mine takes 5 seconds each time
@YTDTETV Жыл бұрын
Hi Lou surprisingly this one started nice and easy, does yours turn over slower? I wonder if it’s a tired starter motor.
@Bristol3490 Жыл бұрын
I have oil leaking from under my gear box it as a vw simble with 3 bolts been tryin to find some1 to let me no wot part its called or if its bad or do i just need a new seal the leak isnt that bad its never driped on the floor just around the seal
@Bristol3490 Жыл бұрын
Its a vw caddy 62 tredline 1.6
@YTDTETV Жыл бұрын
Hi bud I know the piece you mean, I think they just have instant gasket sealent on them not seen them leak before.
@Bristol3490 Жыл бұрын
You a ledge mate i look to see if i can find it online cheers for taking the time to get back to me its not leakin bad just around the seal
@YTDTETV Жыл бұрын
@@Bristol3490 no problem happy to help 👍
@stephenmccready4654 Жыл бұрын
Hi mate do u have any wiring diagram for putting a bkd engine in a caddy thanks
@YTDTETV Жыл бұрын
Hi bud have you seen the video I made on the BKD caddy swap?
@stephenmccready4654 Жыл бұрын
@@YTDTETV yes mate I didn't know if u had any wiring diagram or a list lol
@YTDTETV Жыл бұрын
@@stephenmccready4654 hi bud so I did put the glow stick plug wiring in the description, I write the first part up abit later 👍
@fmnishad1 Жыл бұрын
I have 2012 VW Sharan. oil pressure warning light comes on straight after moving. change oil pressure switch, oil ,Oli filter, oil pick up pipe. still not solved. anyone have any idea.
@YTDTETV Жыл бұрын
I would check the wiring to the oil pressure switch, try earthing the wire to the engine block somewhere as all the pressure switch does is earth the wire out while running, if you try that and the oil pressure light comes still then the wire is broke somewhere
@fmnishad1 Жыл бұрын
@@YTDTETV Thank you
@kennyrichardson1787 Жыл бұрын
Would a engine flush sort this m8
@YTDTETV Жыл бұрын
Hi bud it would definitely help yes but once it clogs in the pickup pipe I don’t know if it would clear completely
@stuartforbes2825 Жыл бұрын
Mine got200000 on clock and I change mine every year going video
@YTDTETV Жыл бұрын
I’ve seen them with well over 300k so there’s plenty of life in it 👍