Vw 36hp okrasa 1400cc build

No video

Vw 36hp okrasa 1400cc build

Рет қаралды 19,734

russellp1982

Күн бұрын

Wolfsburg west okrasa kit with upraged 69.5 crank 80mm pistons and wolfsburg west cam

Пікірлер: 37

@aaronbritcher7121 7 ай бұрын

Very good video. Installation of pushrods once the guide plates are centred while case is apart can be helpful to ensure every clearance is spot on. Also Installation of distributor drive, shim, spring, distributor before crankshaft is installed can be helpful too. Just install with the #1 rod up and that makes it a simple thing too with zero chances of mis-indexing etc. Not essential but might help out others.

@yoshinoyajones8924 6 ай бұрын

I bought a 58 bug with a 36 horse. Replaced the left head and a bent pushrod. drove a 146,000 trouble and leak free miles when it finally left the fleet. only mod was an old nos Abarth muffler. I was a fool to sell it.

@evandrodafonseca8042 3 жыл бұрын

Nice work indeed. My dream engine for my 59 beetle.

@cedricsamir3032 3 жыл бұрын

I know im asking randomly but does anybody know a tool to get back into an Instagram account? I was dumb lost the login password. I would appreciate any tips you can give me

@paultalon4414 3 жыл бұрын

@Cedric Samir Instablaster :)

@cedricsamir3032 3 жыл бұрын

@Paul Talon i really appreciate your reply. I found the site on google and I'm trying it out atm. Takes quite some time so I will get back to you later with my results.

@cedricsamir3032 3 жыл бұрын

@Paul Talon it did the trick and I now got access to my account again. I am so happy:D Thank you so much, you saved my ass !

@paultalon4414 3 жыл бұрын

@Cedric Samir no problem :D

@firealva41 4 ай бұрын

Beautiful motor

@Demopgarage 8 ай бұрын

building one soon, great help mate, what flywheel did you use ?

@jessnevares7861 11 ай бұрын

I am trying to set the cam timing according to the card. With the 4 degree advance washers , I can only get 8 degree BTC. At .040. Will the engine run right like this and How much performance will I loose ? What do you think ? On your video , you are measuring it on the #2 cylinder, intake lobe. I tried it on the number 1 and 2 cylinder. I got the same reading.

@russellp1982 11 ай бұрын

My first cam from them I sent back the holes where drilled off center try it with the stock gears if it reads correct its the straight cut gear if still off cam is off

@jessnevares7861 11 ай бұрын

@@russellp1982 Roger that. I think it is the cam. Depending where I put the dial indicator on the cam lobe, on the inner, center or outer, I get different readings. Sometimes it will show 8 degrees , 10 degrees or even 12 degrees BTC. And this is with the 4 degree advance washers on the cam gear. I wonder how it will run if I leave it ? I’ve been scratching my head. WTF ? 😂

@jessnevares7861 2 жыл бұрын

Question: I am attempting to build my 36hp to the Okrasa upgrade. I ordered the head and carb kit from Wolfsburg west along with the 81mm piston kit. Can use also the 69.5mm crank with these pistons ? And also use my stock rods ?

@russellp1982 2 жыл бұрын

Yes that's what I used stock rods 69.5 crank

@jessnevares7861 2 жыл бұрын

@@russellp1982 thanks for reply. So the 81mm pistons also worked well with the 69.5 crank ?

@russellp1982 2 жыл бұрын

@@jessnevares7861 yes you have to check clearance on the rods and piston skirts but they will work they were made for it

@jessnevares7861 2 жыл бұрын

@@russellp1982 rock on 🤘 I’ll keep your video handy. Thank you 🙏

@jessnevares7861 2 жыл бұрын

@@russellp1982 few more questions. Did you also use the stock rocker arms and oil pump?