Vw Tiguan -09 P2015 (Intake Manifold Runner Position Sensor)

Рет қаралды 77,848

Күн бұрын

It is a very common fault on these 2.0l TSI engines that the intake manifold runner breaks. If the arm that manages the runner should break inside the manifold, you can experience a large vacuum leak. These intake manifolds cannot be repaired if this happens!

Пікірлер: 16

@ramdomdem4301 8 ай бұрын

Jag har samma problem…hur farligt är det om man kör utan att fixa den?

@eriklingsberg6745 2 жыл бұрын

I have gotten the same code on Passat 2.0 tsi 2009. I have located a dead solenoid which should "create" vaccum to the arm which control the flaps inside the intake manifold. I will change the solenoid. I also seen that the arm can be wiggled sideways a bit, basically it pops out a few milimiters, can it be like that or is that also the problem?

@LarsSchonthal 2 жыл бұрын

Hej kul att du tittar på min kanal. Armen ska inte kunna dras ut från insuget mer än max ca 3mm. Mvh Lasse

@eriklingsberg6745 2 жыл бұрын

@@LarsSchonthal Tack för svar!👍🏻

@user-zi9lo2cy3e 3 жыл бұрын

Thanks for your sharing, my VW is 09 Tiguan TSI as well After I unbolted all screw and sensor, but still can't pull the mani out, why??? Did I miss something?? By the way, can you send me the detail photo by mail??

@LarsSchonthal 3 жыл бұрын

I can see if I can finde som poicts. send me an email to lars.s@easy4u.se And I¨ll try to get back to you a.s.a.p

@newportnp1970 2 жыл бұрын

My tdi tiguan is backfiring through my intake manifold when I turn it off any guesses why?

@LarsSchonthal 2 жыл бұрын

Take a look at the valve train, Cam, lifters, valves. Also the EGR, but most likely not. If you have more of a pulse back it would be intake valves. Do a leak down test first, it will tell you where the leaks are or connect a smoker to each cylinder.

@newportnp1970 2 жыл бұрын

@@LarsSchonthal I'm going to try an egr blanking plare to rule out egr blowback took it to garrage and they said we have no clue

@LarsSchonthal 2 жыл бұрын

@@newportnp1970 ok. I hope that you can get it in working order.

@ritzmaharaj8377 2 жыл бұрын

First do a vacuum test of vacuum pump mine was too low changed it....then if error is intermittent 2015 change exhaust solenoid valve for flap which the vacuum feeds... if says stuck open then remove vacuum pipe that goes into pcv valve..test by blowing into it if air goes both ways valve is shot and it needs to be changed...also crankcase pressure is wrong.. u will have oil spots under car. Problem solved

@casanovaevren 4 жыл бұрын

I changed the manifold with sensor and actuator.code 2015 is back

@vasilyordanov4263 3 жыл бұрын

What was the problem

@casanovaevren 3 жыл бұрын

@@vasilyordanov4263 when code is set car runs sluggish.we connected a scanner to delete the code everytime it comes back so it runs better

@vasilyordanov4263 3 жыл бұрын

@@casanovaevren thanks for the update i changed mine as well about 2 years ago. It had a mechanical damage (no wonder, all plastic as you know). But now i get this error again, this time no visible damages. I also have a obd scanner and i did clear the error, but it comes again after couple of days, i think more and more often. So i wonder...

@LarsSchonthal 3 жыл бұрын

@@vasilyordanov4263 It can be a vacuum leakage, check the hoses. Let me know what you get.