I love how detailed this is! Having every little step will really help when installing the hood. Not all contractors are this careful when doing the job - very impressive! I feel like it'll be easier than I thought to install the range hood as long as I have the steps in this video to follow.

I’m here about 9 years after this was posted and it’s helped me greatly! Thanks so much, you have covered everything I needed plus some great tips. 👍👍👍

Thanks most for informing me on how to screw into the studs from the inside of the hood. That's a great tip considering my stud was right in the middle of the mounting holes by the duct. THANK YOU

Wonderful! To the point. Thanks for pouring out your expertise. The tip on placing tape to mark studs is outstanding!

Excellent video. First one I’ve seen that describes locating studs for secondary screws👍

Good to see these educational videos for customers! Thanks Dennis

Thank you - this is the best video I've found for installing the hood!

Thank you for the neat trick about how to attach the hood to the studs and how to not scratch the top portion by leaving the tape in that’s not visible. In Canada the flex hose isn’t allowed. I used sheet metal elbow to vent out

Very clear instructions. Thank you. What if there is a stud on the centerline of the exhaust at the ceiling?

Thanks. I am encouraged to do the install with some help here. My stove is up against a short wall between the living room and kitchen. I will have to build a new wall down from the ceiling to hold a wall mount hood. I understand that the hood should be around 26" above the stove top. That will really leave only a small space open. Would it be safe to have the upper wall come down only as far as the top of the hood, as far as the base of the funnel. I have considered an island mount, but they are a lot more expensive.

great video. i like the way he covered the cook top. the plywood is not only to protect the cook but to become work station . .

This instruction is perfect for us because the duct work was already there. Thank you !

i suggest laying a bead of caulking between the back edge of the hood and the tile or wall to prevent grease buildup.

Thanks for the wonderful video. Usually how much is the distance from the top of the cooking stove to the bottom of the hood? Thanks.

This is PERFECT for ME!!! The Electrical and the Duct work is done, I just needed to mount the Vent. Great Video!!

Thanks for the video. I just would have to disagree with leaving any protective coating on the duct panel trim, simply based on the possibility of it melting when hoods are installed over high output cooktops and ranges.

Perfect. It looks good and this is the range hood I'm looking to install in the remodel kitchen

Great video...to the point and thoroughly explained. thank you for making this video.

How convenient to have an electric outlet perfectly centered.

YEP the most difficult part of the install video left out. The attic access and installing the roof exhaust hood. Plus was this a warm weather climate install or a cold winter climate install. Where the duct probably needed to be insulated in the attic

WOw I wish My Guys were as carefull andor organized they scratched up my range and cabinets etc.. I want you to please do my next installaion. Thak you.

What is the labor cost to get a range installed like this one ? Labor only.

Excellent summary and visuals of steps involved - thanks!

Excellent demonstration. Thank you. May I also ask if we can still get replacement control switch, such as for the Dimplex chimney hood, which seems similar, electrically at least, the one you are installing. Thank you.

I saw a home on which there is no fume hood and there is a wooden cab above the stove instead i don't know if it has a duct outlet in the ceiling or not if we instal a fume hood

Moved into a new home. Noticed that the paint by the side of the rangehood is peeling/staining +- small cracks emerging around joint lines. There is silicone/sealant on the edges of the rangehood, which seems to be deteriorating/having gaps. Is air escaping and this is causing the issues? Do I just need to reseal it with more sealant? Is sealant use normal when installing rangehoods?

Great tutorial. Thank you.

very clear instruction and clean installation. Nice little video !

I thought it wasn't recommended to use long section of flex tube for oven hoods as the grease supposedly stick to the sides a lot more than smooth solid duct? Also, if my current hood uses square (rectangle) duct all the way to the rooftop, is there any kind of square to round duct joint that I can safely use without diminishing the PCM rating of that hood? Thanks!

Awesome video guys thank you!!

He shows the measuring process for cutting off the chimney as measured to the ceiling, says to add 4" and then doesn't show the cutting process and the pre-positioned screw holes are still in the top of the chimney to use to secure it against the top wall bracket. I know I wouldn't want to make the cut down at the joint where it would show - it's impossible to get a perfect cut with metal cutting shears without any crinkling or distortion of the cut edges - so what am I missing? Right now I'm figuring I'll have to make my cut to fit against the ceiling and drill my own screw holes, and then wrap it at the top with some wood stop material as a small crown mold to make a good finish.

Nice video,I have 10” ceiling how I can fit it on high ceilings 👍

Can you install this same chimney hood under the two top cabinets?

can this be installed for an opening out the wall instead of the ceiling?

Thank you for the video - it was very clear and helpful!

Hi that’s the very knowledgeable thank you very much it’s more easier than l think thanks again

According to my building department and the universal building code book, this flex duct is not to code, must use stainless steel, galvanized metal or copper... know anything about this?

can the chimney be cut short if needed?

I'm still confused on one thing. I hope someone can help. My hood fan came with two extra chimneys. One is solid and the 2nd one has like a grate pattern at the top. If my ceiling does not have enough height for both, do I still have to install both (one inside the other)? Or can I just install one of the two? Likely the one with the grate pattern, for airflow...

Best explanation ! Thanks

damn he made that look simply and easy to do, I was readying the installation booklet and it made it seem like a nightmare to install.............smfh

Thank you very much for your video!!! ❤️

So you just vent all the hot air into the void between floors?

Thank you so much. Great video

Great video.. very helpful..Thank You

Thanks for the video!!

Nice video. Thanks for posting. I have one question: when you removed a portion of the film from the duct and left the remainder to prevent scratching as you adjust to your correct height, do you leave the remaining film protector on permanently or do you remove it once the height is adjusted.

Mine sounds like a jet taking off no matter the speed. Is that normal and how would I fix it.

My cavaliere kitchen hood doesn't suck air much.. . very weak. .What part should I check it ? Should it be the exhuast pipe size ?

How about the up to chimney? How?

Great demo. Thank u

Ouch, flex hose used?receptacle right behind duct instead of hard wiring it.?other than that i liked the video.

Hi, thank you for the video it is very helpful! If my backsplash is going to extend to the top of the cabinets behind the range hood should I measure and install per your steps, then remove and install tile? Would it be best to leave the mounting screws further out or use longer ones and tile around them? I realize you may not be a tile specialist so I appreciate any tips you may have. Thanks again!

I am a technician that has to replace those cover panels every once in awhile for cosmetic scratches but I am not allowed to stand on the countertop. What are you using to stand on while inserting the top screws into the mounting bracket?

Exactly what I was looking for. Thank you

NO FLEX PIPE NOT CODE!

hi, I have a question for xtremairusa. you looked up for the stud for the bottom screws, however the upper attachment is the one taking the load of the hood. What happens if there is no stud or other solid backing at the level of the upper screws?? Thanks

Thanks! Super helpful.

what is the standard thickness of range hood

Nice looking cooker hood but sadly far too low. How many of us taller cooks are gonna crack our heads each time we lean in to check our pots on the rear burners.

thank you, fortunately i've found that ceiling bracket inside the hood

How much should this labor cost?

I bought a GE Wall mount range hood. My ceiling is 12 ft high so I need an extension. Can I use a different brand vent hood extension other than GE? Do they all mount similar?

the hood so light?

Great video, thank you.

This really helped! Thank you!

Great and simple

Nice video. I am in China and the Chinese workers short cut everything which normally creates a lot of unnecessary errors.

Anyone know how to reset the CFM. The builder set at 290 and local law is 400cfm, I need more exhaust. The changing the jumper on the circuit board doesnt work after initial install. I even replaced the circuit board, but the cfm needs to be reset on the motor somehow.

Tq

very clear and very helpful!

what does the vent go? outside of rooftop, or attic? We live at an apartment building and there are floors above us, so where the vent will go?

My kitchen chimney hood have the problem after 2 or 3 minutes of start its start making noise (motor noise) what is the solution? Thanks

Thanks for the video...very neat.

Why to install it at 26" minimum? Can I install it at 20"" instead?

Can wall mounted range hoods be vented through the wall instead of through the ceiling???

Valuable info sir thank u

Can I install one with glass tile already installed on the wall?

nice video. .Thank you

you just helped me out a lot!

How much power does this hood draw?

Love it

good vidio thanks

You didn't show to install the flex hose.

How to install a sleeping grease fire for large insurance claims.

can I use range hood on 7' short ceiling

thanks a lot

Did I miss the electric portion of the show?

My lights on my range hood do not come on anymore. How can I fix it?

how the cast

good job thanks

Why is the power supply dire

was is the estimate cost for a professional to do that

can i fit this with out the ducting etc just filters and how

A tarp and a plywood protector? Is the range anchored to the floor?

great video, thanks, 😁

Covering your stove? No! Pull your stove out of there; get closer to your work. Make some room to work properly.

this is so fake , the special effects are totally obvious and the plot is predictable

Notice he didint even test it..hehehe

Jj