Want Micro Crimps?.... Try this DIY Build!

Рет қаралды 5,406

Жыл бұрын

Hey everyone my friends at frictitious climbing sent me a set of their micro crimp holds. These are quality holds for sure but I dont know where I am going to put them. And screwing and unscrewing sounds like a pain so maybe I can come up with something a little more Modular... Let me know what you think. if your in the market I'll leave a link to firctitious below let them know i sent ya!
Stay sendy
Frictitious (not an affiliate) :
frictitiousclimbing.com/?gcli...
My Merch Store!
betaclimbers.com/
You can buy me a coffee here:
www.paypal.com/paypalme/betac...
Here is a Discord link, come join the fun!
/ discord
You can click this link to see more of my videos!
/ betaclimbers
My amazon store where I put products I talk about in my videos. (affiliate link)
www.amazon.com/shop/betaclimbers
Instagram - BetaClimber

Пікірлер: 21

@SamBaker1986 Жыл бұрын

Power tools are aid.

@BetaClimbers Жыл бұрын

🤣

@Jokl92 Жыл бұрын

Tommy Caldwell would like to talk to you!

@BetaClimbers Жыл бұрын

I think these came out pretty nice let me know what you think. 🤙🏻

@mitchellbarnow1709 Жыл бұрын

I think think that they are for pretty advanced climbers.

@BetaClimbers Жыл бұрын

@@mitchellbarnow1709 yeah that’s a good point I’d say if your intermediate go with 10mm first.

@mitchellbarnow1709 Жыл бұрын

@@BetaClimbers Thanks for the great advice!

@frictitiousclimbing4991 Жыл бұрын

Really rad setup! Stoked to have you training on them. If the edges are ripping your fingers up you can sand the edges down to make them comfier!

@BetaClimbers Жыл бұрын

Thanks again! They are very comfy but my home gyms holds are not 🤣 currently healing from some hard sessions. 🤙🏻

@Hungry_Box Жыл бұрын

I need to get an inside training wall, that looks dope

@arjen6782 Жыл бұрын

Sweet set up! Those micros look great!

@tomtom4405 Жыл бұрын

You managed to talk about table saws and push sticks without mentioning Tommy Caldwell's missing finger. That story still makes me wince!

@cathysilva5435 Жыл бұрын

smart smart Great video

@user-fs5bg1xj8t Жыл бұрын

This is so smart

@pascaljutras178 Жыл бұрын

Very good way to get any position possible. After watching this I feel like I should get good hard wood and take my wood router to create my crimp holes, i could create whatever I want.

@alexnone5720 Жыл бұрын

As much as I don' like youtube power tool safety comments.... Cutting pieces that are short and thin and leaving them between the blade and fence can end up with one being launched back at you if it catches the back side of the blade. Use a spacer block against the fence but behind the front of the blade so you end up with an extra few inches between the cut off piece and the fence. Nice concept overall for quick change training holds.

@BetaClimbers Жыл бұрын

Always a big fear of mine. I want to build some jigs for cross cuts and stuff. Thanks for the safety tip much appreciated!

@alexnone5720 Жыл бұрын

@@BetaClimbers No need to go full cross cut sled unless you have more projects. The cheap miter bar the saw comes with will do most work, just don't use the miter bar AND the fence at the same time with short pieces. Either pulling the fence off or sliding it a few inches out of the way will do the trick. For mostly repeatable miter bar cuts you can mark the table top with a pencil line.