Washer Repair: How to Unclog the Drain Pump

No video

Washer Repair: How to Unclog the Drain Pump

Рет қаралды 347,715

Күн бұрын

For more help troubleshooting a washer that isn't running properly, and to find the right part and installation video that works for your specific model, visit our symptom-based repair page on our website! www.partselect...
Is your washer's drain pump clogged? This can cause your washer to leak, or simply not run as it should. Steve will take you through the basics of how to unclog the drain pump. and get your washer working like its old self!
Is your pump damaged, and needs to be replaced? Simply enter your model or part number into our website to get started finding the manufacturer-approved part you need!
www.partselect...
Need help installing your new part? Check out our Washer Repair playlist to find step-by-step instructions for replacing your part quickly and easily at home!
• Washer Repair - Replac...
PartSelect is committed to providing you with high-quality parts, quickly and easily. Find out more about our fast shipping and interactive customer service on our website.
www.partselect...
Don’t forget to Like this video, leave a question or comment, or Subscribe to our channel for more helpful troubleshooting and installation videos for all your major appliances!
All of our products are genuine OEM parts, sourced directly from the manufacturer so you can shop with confidence, knowing that your part was designed specifically for your appliance!
Follow us on Social Media and check out our Lifestyle Blog!
/ partselect
/ partselect
/ partselect

Пікірлер: 56

@jackiebrowne4285 4 жыл бұрын

this guy is so knowledgeable! This stay at home mom who is trying to address some items on hubby's fix-it list really appreciates these videos I have been finding

@coreyw1831 3 жыл бұрын

Go girl!!

@wellnesspathforme6236 4 жыл бұрын

A quick note - the symptom of the washer stopping and failing to rinse and drain can be caused by a piece of small clothing getting stuck underneath the center agitator spindle. In my case, it was not visible and I only recognized this when I went to spin the agitator spindle around and the rinse cycle began to run. I fished around underneath the agitator and pulled out a small piece of clothing. Removing said clothing item ultimately resolved my main. Unfortunately, I didn't know this and ended up doing a pump replacement as "preventative maintenance" instead of problem resolution. *My lid-closed sensor apparently failed during my work on the unit, so I jumpered it with solid speaker wire and put it an order for a new door sensor. I followed this gentleman's instructions for the lid jumpering. As he points out, unplug the unit as your first step - even before disassembling the unit to get access to the switch connector. Whirlpool / Kenmore Washer Not Draining - Lid Switch Test kzfaq.info/get/bejne/pJd3acthqrXQkqc.html

@herbertmedina8396 4 жыл бұрын

Would have been great if you showed us the whole thing including removing the instrument panel. Having trouble removing the panel from that model Kenmore 400 washer.

@oliviad6713 4 жыл бұрын

I agree, this sounds great, but I'm a total rookie - I need to know how to take the panel off and remove the pump!!!

@joydavis9264 3 жыл бұрын

Ten months too late but... watch?v=b-45BWyuTiI (copy and paste that above after the slash at the end of the youtube address and watch that video. But I just tilted my washer back and leaned it against the wall and laid down in the floor looking up under the front of the machine myself. It wasn't hard to remove at all. And I'm a chick who has no knowledge of repairing things. Just watched a youtube video like you. ;-)

@kitchfairman5043 3 жыл бұрын

@@joydavis9264 That's H0TTT!

@jlamb199 Жыл бұрын

@@joydavis9264 I changed a part of the pump on my washing machine about 5 years ago, (also a chick), and I didn't recall taking the cabinet off! I think I'm gonna grab my 2 ton jack out of the garage for a bit of stability this time. THANKS JOY! I thought I was losing my mind! LOL

@newtown5698 3 жыл бұрын

I removed and rinsed my GE washer water pump few times, put it back on, and is working now just fine (it was not spinning nor draining), so I saved some money.

@mfoukes 3 жыл бұрын

I had neglected my washer and dryer for years. With a lot of work needing to be done, your videos have helped me tremendously. Thanks!

@lauras2535 3 жыл бұрын

I found a big clog of fabric shreds in that tube on both intake and output sides and was able to fix on my own! Thank you!!!

@its.me_angie Жыл бұрын

Thank you for this video. I suspect this is the issue with my top load kenmore, but I don’t own pliers to confirm. 😬 This is a good video to pair with other videos I have found.

@tomuhle4880 2 жыл бұрын

Steve gives an excellent presentation. I highly recommend.

@iRollWithPunches Жыл бұрын

Thank you sir. There was a bobby pin stuck in mine. Works like a charm now!

@partselect Жыл бұрын

Glad it helped!

@andreadrever1073 11 ай бұрын

WHERE is the pump????

@NOTIFIGIBSON 2 жыл бұрын

With basic knowledge of what needs to be done these videos are great. Thanks for taking the time to make them

@perfectscore6909 Жыл бұрын

That fixed it, I'd found a $5 note in the water pump. Thank you.

@imaxfli 5 ай бұрын

What did your machine do that made you know it had a problem????

@perfectscore6909 5 ай бұрын

@@imaxfli It wouldn't spin dry, the machine kept giving errors when the spin cycle started. because it wasn't able to pump out the water

@johncullenjr8741 Жыл бұрын

Vacuum out water through drain hose attached to back at low grade Ah flip it on left side if you have the room 3/8 nut driver may need ratchet with extension if its on either side for one bolt. Remove install no problems. Press in tap to remove wire. Done

@newsgetsold 4 ай бұрын

But this doesn't say what would be the symptoms of a clogged or faulty pump? Wet clothes? Water remaining in tub?

@teliabaxter5730 4 жыл бұрын

This was so helpful! I was able to remove the pump and the small piece of fabric causing the clog. Thanks so much!

@imaxfli 5 ай бұрын

What did your machine do that made you know you had a problem???

@justnii2056 10 күн бұрын

If rosenlew drain pump is stuck exc. How can i maintenance it

@shanesubashe787 Жыл бұрын

This fixed my problem. Thanks!

@chastitymcfarland2616 Жыл бұрын

I just replaced the clutch on my washer following your video. I went to go run a load through and it got as far as rinse cycle with a full drum of water. Does this mean I have a clogged pump?

@Mrlin13 2 жыл бұрын

Very easy to understand, thank you!

@christierobinson7707 Жыл бұрын

Good info, thanks

@breakingbadheisenberg9703 2 ай бұрын

Could my kenmore elite be humming and not working because of the pump being clogged? I have pets .

@flyfast77 3 жыл бұрын

I think because of my washer not draining it overrflowed outside of the drum.... is there any maintenance I need to do on that!!???

@madmikemackas Ай бұрын

I’ve got an A9400 1980s style Maytag washer with a burning smell and washer will not spin on spin cycle. It agitates fine. Washes fine, rinses and drains fine. The only problem is the burning smell and the spin cycle. Replaced both belts. Replaced motor. Detached drain pump and it was clear as were the inlet and outlet hoses and ports. Water rinses through the pump fine as well. wtf is going on? It’s maddening ???? Anyone please

@Bomber411 3 жыл бұрын

What about with a portable washer? I have a 6kg Daewoo and can't find anything on it online. It's making a horrible buzzing sound like a fluorescent light buzz, but it's running.

@reginaldmcleod9326 2 жыл бұрын

After the spin dry the clothes are full of lint. What's is causing this. Is there a filter that needs to be cleaned

@partselect 2 жыл бұрын

That's a really great question and the answer depends on what make and model washer you have. Some manufactures do have some filtration pieces in them but many washer today no longer have them. Linting is a real issue with top load washers , they require such a balance of agitator speed and proper water level, not overloading and quality fabrics. Some types of material easily give up threads of fabric especially when they get older and fray easier. I am curious if this has been a constant nuisance for you or something that has just recently showed itself? If recent then review if anything has changed in your washing process? Different detergent or water level settings, even water temperature setting can effect washability.

@jlamb199 Жыл бұрын

@@partselect I actually think that it's due in part to the poor quality of fabric material used today. I have hoodies that I've had since college, over 40 years ago and are still in good shape. Brand new ones, no matter how much $ I pay for them, are washed 4-5 times have pils and lint every time they come out of laundry day. Lint rollers don't make me happy. It's disheartening, but thank you for your video. 😊 Judy in NY with a Kenmore Series 80!

@edwardoak2636 4 жыл бұрын

My washer's not clogged, but clothes always come out dusty even when wet.

@crystalmarie3614 Жыл бұрын

That's how ours are coming out how did you fix it

@lilaleahg 2 жыл бұрын

I unclogged my drain tube, and then my washer lid locked. What happened?

@artfuldodger7838 2 жыл бұрын

But HOW THE DEVIL DO I GET TO THAT WATER PUMP??? Like, show what has to be removed, and show removing it. This is an unhelpful video. I need to know how to get to that pump.

@jlamb199 Жыл бұрын

You mean how do you take off the cabinet? If you have an old machine you need to take apart the top and flip it back. Then the front and both sides (with the lid open) tilt forward and lift up and out for access. TightWad has a DIY to explain it perfectly.

@artfuldodger7838 Жыл бұрын

@@jlamb199 I asked this 7 months ago, guy.

@jlamb199 Жыл бұрын

I found this video helpful for my purposes. You need to search for what you need because all models are different.

@jlamb199 Жыл бұрын

@@artfuldodger7838 First of all I'm not a guy, secondly I'm trying to help you and finally maybe you haven't noticed but he doesn't respond to most comments, especially not the rude ones. Looks like you're on your own.

@-roejogan- 3 жыл бұрын

Let's say that while doing this I accidentally got water all over the copper by the drain pump. I dried it with a towel but how long until I can plug it in?

@orangebeagle3068 3 жыл бұрын

I think 9 months should be fine. You can plug it in now.

@-roejogan- 3 жыл бұрын

@@orangebeagle3068 lol good one