Watch THIS Before Replacing Your Fuel Tank

No video

Watch THIS Before Replacing Your Fuel Tank | Fuel Tank Restore

Рет қаралды 12,503

Күн бұрын

Hey there boat enthusiasts! Are you ready to join us on an epic fuel tank restoration and installation journey? If so, buckle up and let's get started!
In this video, we're going to show you how we transformed a sad, neglected fuel tank into a bulletproof, new addition to our boat. We'll walk you through every step of the process, from cleaning and prepping the tank to applying a protective coating and finally installing it in the boat.
But it's not all hard work and no play - we promise to have some fun along the way and give you some helpful tips and tricks. So sit back, relax, and let's get to work on bringing this fuel tank back to life!
#boatrestoration #gradywhite #boatlife
::Amazon Link::
www.amazon.com...
We may earn a small commission from qualifying purchases.
Thank you so much for your support. Every little bit is much appreciated and helps us to grow this channel!
Instagram: @PerfectFitBoating
PerfectFitBoating.com
Check out our website for merch and our ebook all about wiring your boat!
Thanks for watching!
-Andres & Aliey
The Perfect Fit Boating team
#gradywhiteboats #boatrot #boatstringer #bulkhead #fiberglass #boatrestore #repair #Boatrestorationproject #fishing #Gradywhiteboat #Gradywhiteoffshore24 #gradywhiterestoration

Пікірлер: 47

@jorgegorina3039 29 күн бұрын

Nice work man!

@perfectfitboating 29 күн бұрын

Thank you buddy!

@garyg5829 16 күн бұрын

I’ve used the marine Tex on my tank with some pitting and it worked great. I also used it on a pump housing under 30lbs pressure and it hasn’t leaked yet. Next year I’m going to fabricate a new aluminum tank for mine . Great video

@perfectfitboating 16 күн бұрын

Thanks Gary! The marine Tex worked great. Been over a year and zero leaks! We’ll eventually get a new tank too! 🤙🌊🛥️

@2BearsOutdoors Жыл бұрын

It's going to be like new by the time you get this boat done.. Great video.

@perfectfitboating Жыл бұрын

That's the plan! Or at least come close! 🙌🍻

@2BearsOutdoors Жыл бұрын

@@perfectfitboating loll.. I like that plan. 👍😁

@choimdachoim9491 Жыл бұрын

Very helpful. I found 3 items I need for my tank project.

@perfectfitboating Жыл бұрын

Awesome! I’m glad it helped you! 🍻

@davelawrence6777 5 ай бұрын

You did a great job on restoring that boat I do believe it might have actually been worse than. Mine was. It's such a rush when it's all done a d you see people at the do k staring at it in awe of whst you accomplished .

@perfectfitboating 5 ай бұрын

Thanks Dave! We had no idea what we were doing and just jumped in. And now is when we’re finally trying to make it look nice and acceptable. We’re gonna show every step of it too. 🤙

@oceanairbrush 4 ай бұрын

The bedliner you use is a water-based product. I would have gone with a urethane-based product such as raptor liner for better results and more permanent resistance to the fuel. Also, you really should have laid it on thicker in my opinion. That said, you did say it was a temporary fix. Love the videos. Keep them coming

@perfectfitboating 4 ай бұрын

Youre 100% correct. Just temporary till we get a bigger tank put in. We got more coming! 🤙

@oceanairbrush 4 ай бұрын

@@perfectfitboating One of my first boats was a 1985 Grady 197 tournament. I went through much the same experience as you have gone through. I can personally relate to 90% of what you're posting. It makes me laugh because I remember thinking. Am I crazy, obsessed or just making poor decisions? Then I realize what the vote was worth after I finished and what it would have cost me to buy one do and I was extremely happy and proud with what I had done. You will be as well. I boat over at the haul over Sandbar every now and then, so maybe we'll run into each other. So I'll be sure to say hello if I see you

@perfectfitboating 4 ай бұрын

@oceanairbrush you know what’s even funnier? Next week we’re picking up Alieys dad’s boat to re do the transom. And it’s a 1985 Grady tarpon I believe. Dual console! I often ask myself if I’m crazy! But when we go to these boat shows I realize I’m just a little crazy and saving tons of money lol. If you ever see us out there please say hi! We’ll grab a beer and shoot the sh*t for a bit! Cheers!🍻

@oceanairbrush 4 ай бұрын

@@perfectfitboating you are not kidding, with the prices of new boats nowadays. I do not understand how everyone is not doing this

@greauxpete Жыл бұрын

If you must patch it, I would reccomend patching the tank with gflex epoxy on 1708 with the mat side down. Gflex has a track record on aluminum and plastic. I personally patched a plastic tank i accidentally drilled through with gflex. Worked great. BTW, great work. We have 27 ft grady islander and are in the process of refurbished the starboard side stringers.

@perfectfitboating Жыл бұрын

Thanks for the tip! I originally wanted to use glass over the tank and at last minute decided to go with the marine Tex. We appreciate the kind words! You should post some vids of the build! We’d love to see it! Not too many vids of people fixing up their Grady’s. Good luck and hopefully you get out on the water soon! 🍻

@greauxpete Жыл бұрын

Sent you an email with links to our project

@perfectfitboating Жыл бұрын

Awesome! Thanks so much!

@AJOutdoors1 Жыл бұрын

Nice work, I hope that tanks holds up for you. Knock on wood I have not had to deal with a fuel tank issue yet.

@perfectfitboating Жыл бұрын

Thanks! I have a buddy of mine that fishes commercial and he made a similar repair but without the bedliner paint. He’s had it for 5 years with out any issues. Best is to replace it. But that’s an $1800 expense we’re not willing to pay right now lol. Once we upgrade motors we’ll change out the tank

@AJOutdoors1 Жыл бұрын

@@perfectfitboating Sounds like a good plan. BOAT Bust Out Another Thousand. LOL

@perfectfitboating Жыл бұрын

Brother you got that right! 😂

@mpal8264 5 ай бұрын

How did you discover the pin holes and did you video the patch you referred to?? Thanks. Nice job, electrical work looked solid.

@perfectfitboating 5 ай бұрын

The tank had fuel in it so I turned it and saw where the fuel was coming out of. I also inspected it closely with a wired hair brush and anywhere there was corrosion I just brushed it clean. Then I just used the epoxy putty like in the video. Thanks for the comment brother! The electrical work came out great! Just gotta try to work on my neatness! 🤙

@johndrazic7665 4 ай бұрын

IMO don’t think bondo and spray painting a leaking corroded fuel tank is the place to save money. Best case, you bought some time before it leaks again, worst case…….kaboom!

@perfectfitboating 4 ай бұрын

Well it’s not bondo and spray paint. It’s epoxy paste, etching primer then truck bed liner. It’s been over a year with no leaks and I don’t see how it would explode anymore than a leaky tank. Either way, we do plan on changing her out in the future. Thanks for the comment!🤙

@Spicy-Tuna Жыл бұрын

Good stuff man. You undertook a massive project for sure. I'm restoring a Sailfish 274 right now. One of the rare Diesel sleds. I'm hoping you got the thing for free having to do all that work. Looks like a nightmare honestly. I would have passed on it for sure. I actually came to this video because you guys said you were going to say how much you paid for the boat. If you need some advice, let me know.

@perfectfitboating Жыл бұрын

Thank you for the kind words! We paid $700 for this thing! So, not free but pretty darn cheap! I don’t think I’ve ever seen a diesel sailfish! Do you have videos up? I’d love to see the restore! Thank you so much for offering your help! 🍻

@Spicy-Tuna Жыл бұрын

@@perfectfitboating i only have pics at this point. Id be happy to share offline

@perfectfitboating Жыл бұрын

@@Spicy-Tuna yeah we’d love to see them! Shoot us an email perfectfitboating@gmail.com

@Spicy-Tuna Жыл бұрын

@@perfectfitboating righteous. Will do

@nwrx247 2 ай бұрын

How did u remove the tank .like how u pulled it out

@perfectfitboating 2 ай бұрын

We yanked it out by hand. It’s not foamed in so it came out fairly easy.

@nwrx247 2 ай бұрын

@perfectfitboating I have s 2981 G.W 24 offshore, and I unleavened it with tge ropes it looked like it was being held by.but it appears that it's stuck by foam .that's why I ask .also would like to rewire ir ...ant suggestions. I'm new to this

@perfectfitboating 2 ай бұрын

@nwrx247 is your tank in the rear or front compartment? If it’s in the rear you have more space to get leverage. I’d try to take out as much foam as possible first. Dig as much of it out as you can. Then if possible find a long enough piece of wood to go across the beam of the boat on both gunnels. Then tie straps to the fill and the pickup tube and tie that to a come along on that beam. Slowly ratchet up till it comes loose. Foam is a bear to release so try and get as much of it out as you can. Hope that helps!

@nwrx247 2 ай бұрын

@perfectfitboating in the front ,with a pull chain .I just yanks it .working by myself it took a little time amd alot of effort but it's out the boat

@nwrx247 2 ай бұрын

@@perfectfitboating I meant to say 1981.gradsy white.

@michaelwhitmore5259 Жыл бұрын

so, you didn't address anything on the inside of the tank? or did I miss that in the video?

@perfectfitboating Жыл бұрын

We cleaned the inside of the tank but that wasn’t in the video.

@andrewdedomenico4464 3 ай бұрын

@@perfectfitboating What did you guys use to clean out the inside of the tank (products, solvents, tools)? Also, how did you remove the tank? The wedges around the side were reluctant to budge in mine making a simple two man lift impossible. Big fan of your channel by the way I just found it this week. I have a 1985 Grady 24 offshore as well with very similar... age related injuries. Nothing the TLC can't fix like you have proven in your videos. Great boat!

@perfectfitboating 3 ай бұрын

Hey Andrew! We were instructed to use something as simple as dawn detergent and water. We sloshed that around over and over again then hit it with some pressure. Since our tank had oil and fuel mixed previously, this method cleaned it out extremely well! I think the going rate for a tank clean is $500. To remove the tank it was fairly easy. Our tank was in the rear access hatch and was not foamed in. It was a tight fit to get her out but she came out just fine. You might want to get a multi tool and cut down the wedges if they’re stuck then just make new ones. That’s funny we have the same boat! I gotta say it’s very sea worthy, has tons of space and serves us well. And for the cost of a new boat I think you can fix up 5 of ours! 🤣 Oh, last thing. If you’re taking out the tank, consider moving it to the forward compartment. It really helps balance the boat and keeps the bow from coming up too much. We don’t have trim tabs and we heard they like to hit hard if you don’t trim down. So far it hasn’t been too bad unless it’s a quartering sea! And, despite what I read online, it’s not that wet of a boat!