Thanks for the webinar

Maraming salamat po. Nagkaroon kami ng panuntunan at dagdag kaalaman hango sa literature ng gender control module. Naniniwala ako na kayo po ay Filipina na eng'r sa larangan ng elektrisidad. Mabuhay po kayo.

Informative video about Gensets synchronization...

Thanks jubili bros very useful vdo

Thank you very much for kind share of technical support

It was very helpful!

I believe in your explanation regarding the 4 generators feeding the load. Though the 4th priority generator started in the intial start up, the priority 1 generator will start, sysnchronize and share the load. Gen 4 will shut down thats how the priority system in Deepsea 8610.

thank you to share about dse electronic.

hi,thanks for this video

Thank you so much for sharing this video. I want to know if DSE 8610 MKII can be used to synchronize both DG and Grid power or solar power. Also what is the function of duty select configuration? Thank you

thanks so much .....

Thank you so much for the educational info.Can i apply this into paralleling to grid and solar.

Thank you so much

Thank you

Many thanks for sharing informative presentation. is the system needed to have synchronizing panel?

when synchronizing generators does the DSE8610 has built in compounding current transformers or these have to be provided by the customer for each unit

Very cute voice

Thanks

Hi, thanks for the video. Do you know how to remove the pin fro DSE 7320?

Dear Sir, Please if I have a screen DSE 8610 MKII and replaced it with a screen of the same type or you made firmware update, how do I transfer the SCADA settings for the screen? Do I record it before replacing or before firmware update and then manually transfer it to the new screen? Best Regards

perfect

In case communication failure between Ecu and d.g controller how set it right and what are possible resons.

how to change the parameters on the panel 8610 to control one input in the absence of three phases, it turns on so that it turns on, and when three phases appear, it turns off.

I have an interesting and intiguing question. Your answer will really help. How to combine two AC source for higher power output? I have 5kw inverter off-grid solar system which can't provide enough power to run a 5 kw motor machine. I also have 3 kw generator. How to combine 5kw solar system with 3kw generator, to get 8 kw system, for generating enough power to run 5 kw motor machine? The inverter specification and generator output is given below as shown in picture: Inverter Voltage =220. Generator voltage =230V±5% Inverter Hz = 50hz . Generator Hz= 60 Hz or 50 hz Inverter wave form= pure swine. generator wave form= not given.

Meron ba physical training o seminar nito?

👍

Hello ,i have follow the instructions 2Gen synchronize perfectly but there Circulation current very high wht is the cause

Dear, what is the difference between 8610 LS and 8610mkii LS

could you please give information in GCP-1 CONTROLLER and 6000 series regarding synchronization please

Good😂

When dse8610 MKII used for synchronization, is it compulsory for remote start signal connection on each generator? or msc link will perform that task?

hi. Can we use dse8610 with out ECU connection? because our diesel engine doesn't have ECU.

can you drawing full diagram synchronize 2 genset with DSE 8610

hola quiero aprender sincronismos. saludos

Please reply 🙏🙏 it very important for me

Tienes videos en español?

How we can sync 8620

من فضلك عندنا مجموعة مولدات مربوطة تزامن مع بعضها ...وعندنا في المعمل مصدر قدرة 513VD Link یعني نغذیها بثلاثة فیز 380فولت وتخرج 513VDC لتغذیة انفرترات تشغیل مجموعة من المحركات المشكلة عندما یتم فصل الحمل بالكامل مرة وحدة ترتفع الفولتیة من 513VDCالی تقریبا 600VDC

Tienen información en Español

How make English language ?

Can I have your e mail.will it be possible that you configure our 8610 controller base on our operation and charge me for setting out controller. In case may we know the cost

If anyone have email for this company Taxt here please