Yes, cocking the sear arm is necessary for all HW models to make installation of the trigger unit easier.

The simplest and the best video on KZfaq!🛸💰

Cheers for this, We have to strip a 77k down over the weekend so this is really helpful. Thanks.

Great instruction video. Nice job and Thank you

Earlier today I stripped my HW 77 down and did TNT and clean up! Don't think it has ever been stripped down before? I got it second hand and I see where some previous owner had tried to tighten stock screws with standard screwdriver instead of a Gunsmith set of tools? Thank you! WOW! Semper Fi!

Very well filmed video that shows all the component parts of the strip down but would be much better with some dialogue. Dont be shy

good filming angle , all was so clear, was afraid when you were unscrewing the main spring casing, thought the spring may kick out .. but went smooth. good.

Beautiful rifle. Very Nice!

Very nice video! You have a beautiful rifle!

Great video, nice and easy..

Very good video. I've just bought a second hand HW77k, around 1984 vintage, and will be stripping it to have the action reblued. Might as well replace a couple of parts, too. I'll also be using your greasing video to help me with that.

grate vid, just sorting out an old 77 myself.

Nicely done!

Just stripped and re springed my HW77K following this video thanks a lot :-)

nicely done mate

super video

first of all thanks for this video, can you please tell me what can be the cause HW 77 in order to be fired the safety catch must be pressed continuously in order to fire .

Before watching this I imagined I might need a workbench!

Well done, made it look easy lol.

great video. Thank you very much

Sweeeet! Thanks for the reply and yes it is indeed. :)

Very few steps are different. The trigger housing must be rotated out of a little notch. Very easy to do if you take an allen key and poke out the four small blocks which are located on the left and right side of the trigger housing after that place cylinder on a small rubber object and rotate counter clockwise. The trigger housing should come right out.

Excellent !!!

Yep. ^^

Thank you very much Sir

excellent. hoping to buy a project hw 77 tom. looking forward.

hei how many footpounds does the hw80 in 5.5 more than the hw77?thanks

Many thanks.

Greetings, the trigger guard does both of its screws connect to the trigger action block or to the wooden stock? Thanks.

Dont hang around do you? nice vid man and congrads on your new rifle funkmanghillie

Will be doing the same if I can get my hands on a second hand wh77 tomorrow. 150 quid at the dealer, not too bad I think.

Someone requested a strip down video don't know who wanted it to see but now he can. ;)

Thank you for the video... I used it to see how to disassemble and reassemble my HW77K... the orientation of the "anti-bear trap assembly" got me confused because the piece held by the spring got turned around after I removed it... so I had to re-watch your video... I saw another video where the gunsmith had already removed the anti-bear trap since it really serves no useful purpose, as long as you know to always hold the cocking lever or barrel when loading a pellet... apparently, when you remove it, you can now de-cock the rifle, which is nice to be able to do... I left mine on for now, but may end up removing it later.

Super. Thank you.

Thank you so much for you answer! Have you tried the accessory VORTEK ProGuide 2 If you have tried it, do you know how many Joules the Feather will give a Hw50s with .22 caliber? Thank you very much!

Do you have a strip down video of the HW50s? If not, what steps are different? Thank you very much!

nice one buddy

With heat and force.

thanks a lot for posting this very interesting video, I have one what could be the cause I must keep the safety pin pressed in order to fire it

Nope, there's just the serial number on the barrel.

Hope I could help. ;)

How do you get the under lever locking trap off at the end of the barrel

Muss ich den Abzug ausbauen oder reicht es, den Block, in dem der Abzug sitzt, herauszudrehen, um einfach eine neue Feder einzulegen? Besten Dank!

So, @ the 4:30 mark when you took the wrench and covered it w/ a towel and whacked it w/ a screwdriver & started loosening that part, this is when you need the compressor w/ a Beeman? Can one hold it straight up and down on the floor and control the spring that way? Thx.

That would be possible, but be careful.

Estou precisando de um kit vortex 16j pra minha hw 97 pode me ajudar

Спасибо!!! А пневматическую пружину не пробовал ставить?

springs of several millimeters so you thankyou

Nice thanx

Hi on the Weihrauch as we know there is a serial number is there other numbers like on the stock that match ? Just wa

bravissimo

I noticed there’s no top hat in the mainspring, just a spring guide. Are all 77s this way? Just tuned two 99s’s, and they both had top hats🫣 Maybe its still in the piston. This is often the case…With a few washers too. Nice job🤗

Nice

hopefully you still read your comments; it's my first time disassembling it, and i can't get this part done 4:22 i use the same tools and hit the same way, even harder, it won't move at all, i'm even afraid to damage it knowing how hard i've been hitting. Was it the same for you? cheers

lider 44?

Very nice video. But I stuck at about 4:25. I'm totally not able to unscrew trigger housing (hopefully I use correct name for the thing that needs to be unscrewed to get spring out). You used a few pokes of screwdriver but for me it looks like it is glued. Any ideas?

Good

Just curious , thanks !

why cant i just put two springs in it. wont that help?

der hintere Teil wo der Abzug drinnen sitzt ist doch inzwischen nur noch schwer abzubekommen bei einer neuen Waffe, da die Sicherungsmittel für das Gewinde verwenden, hast Du das auch schon festgestellt? Dass Du nicht mal einen Schraubstock brauchst ist der Hammer

This Mk1 Or Mk2?

I bought an HW77 .22 with a red dot sort of scope £60.. I know absolutely nothing about guns.. So i was just wondering if that was a good price? Ps nice video :)

the spring i took out of the beeman rs1 is 11.5 inch long, 44 coils, 15 mm out dia, inner 10 mm, wire thickness is a darn 2 mm :-)...I will contact Weihrauch like you said..the spring u have look thick 380 ms

Hello, is that a full power version? Thanks!

With a dentist's tool (hook) it should be fairly easy to pull it out. To get it in is easier. Just push. ^^

I guess it's a good price and a very good air rifle too. ^^

Kann man nicht einfach eine Feder von einer HW98 in ein HW57 einbauen um eine stärkere Leistung zu erzielen weis das jemand?

where can I buy a v match kit?

Price=? Made by=?

My hw77k is not latching on when cocking.

I just thought id like to add, when putting the rifle back together, when you screw on the end piece where the trigger unit goes make sure it is lined up perfectly before screwing in the trigger guard / stock screw. mine was misaligned by about 1mm but i screwed in said bolt thinking it would just tighten and line everything in, but no. instead i cross threaded virtually all the threads and f**ked my bolt. just so you know =)

Hi

is this a full version rifle??

i have just purchased a 2nd hand one of these today.Its an 80's (west german) model.I will probably strip it down so this is very useful for me.Does it have a breech seal too? If so,how do you remove it?

U know the rifle inside out

I can never understand why there’s none speaking stripping guides seems daft. Each to their own I suppose. Good video though nice clear view of what’s going on.

stripped*

Wow I can't believe you guys can find these things used for sale. I am waiting for my HW77K to arrive and I can safely say I will NEVER part with it. I am 43 and haven't even seen one of these things in person before. Mine cost $600+14% taxes + shipping Canadian/US $ same these days plus the scope. It seems as though you guy by them cheap over there." I wish" man I'd own every Weihrauch underlever model made. I still will but it's going to cost me lots more.

kann bestätigen dass die Qualität nachlässt, neue HW 97 KT, nach 100 Schuß Laufgewicht lose. Reparatur dauerte fast einen Monat, danach Kratzer im Schaft:-(

بھائی لیور بنانے کا طریقہ بتاؤ

Are you a proff gunsmith?

can you guys watch this video and help me out thx pellet gun problem need maintance please !!!!!!!!!!!!!!!

First date with her and all ready strip her down...man thats wicked.

Me gustaria ber estos nideos

Riyal prais and point pleasant tellme

Loctite free?

Ever thought of being a gunsmith?

vasava hai

Thighs of steel!

Excellent !!!