😂😂😂

he did lube the rubber, you can see the oil on his finger. He tightened it like a real Ahole. I always reference these types of filters when goofballs say that you need to fill the filter, that would be a neat trick.

@@arnold8746 You can also see there is no footage of him putting lube on the rubber.

😂😂😂😂

#4 It's a jeep thing 😂

Stole the words out of my mind

Job security. You HAVE to bring it back to him every time for an oil change.

Right up until you he strips the threads

I mean given the location it's not like it'd be that hard to get that one off.

My brother in Christ, I started my own synthetic mobile oil change business THREE MONTHS AGO. That stupid Toyota/Lexus canister filter is on beyond tight 4 out of 5 cars. I have a 445lb-ft impact and held the trigger down for 10 seconds and it would not budge!!!!!

Thats f- ing funny!

🤣

That's got me in stitches my boss always has ago at me cause I go mad at these twats that tighten everything that fucking much I'll show her m this now 😂

Thank God for breaker bars!

Or 1/2 to 3/4 a turn more after contact.

​@@Rhaspunthat's my go to. Hand tighten, then add a quarter to half turn.

@@DerPilotMann Due to my job. For several years I didn't have time to do my own oil changes. When I switched jobs, I ended up having a lot more time at home. So I started doing my own oil changes again. The local oil change place who I went to barely tightened the filter at all. Without exaggerating, I could just use only my fingertips to twist the filter off. I was lucky the filter never fell off! They used a oversized drain plug gasket. When looking at the marks on the gasket it was less than 1mm away from not having full contact.

There is a recommended torque soec for oil filters. Usually in neighborhood of 15-18 ft/lbs

Not on my vehicle. Mine states, in the manual, torque to 24 foot pounds. So that's what it gets. And yes, I mean every word of that. As a general rule, yeah hand tighten, with a lubed o ring, fire up check for leaks. Hell, I use th3w wrench to add an exta eighth pr quarter turn, as I got mom's hands, not dad's. Medium palms, short fingers. I don't, canister fiters spew, because I can't grip a standard filter, and tighten it fully. I've tried. The old 3364 ones on a 2.2 Chrysler, sure. PH8 or 16, not enough purchase. On the current vehicle, 17 Grand Caravan SXT, 3.6 VVT. They don't use a screw on filter. It uses a housing. As do the motorcycles I've worked on for the last 28 years. Never say never. Because exceptions always exist.

That was so funny I laughed my ass off you are truly hilarious

My God that was funny. But you are right. The only other thing he could do to the next guy would be draw a middle finger on the filter.

correct!

He forgot to use the impact gun to tighten it up

🤣🤣👍✌️🇬🇧

Good we don't want you

Exactly, and one time - there was trainee in workshop, and he was trying to unscrew oil oil drain in wrong direction. When he go for extension bar (I as young and unexperienced with car these days) I suggestesd to try it in differentdirection and it goes... Thank God I told him this... If he thad tried to do it with extension - I'll had to pay for sump replacement....

That's not an oil change shop. Quick lube stores will use branded oil filters most of the time. That's an stp bottom shelf filter.

Could be worse. He could of used a Fram filter. @@joshuaburdo2140

I hate those douche bags that don't think or care about the next guy down the line

It don’t got no gas in it

Omg lmao oil the seal and hand tighten that shit is NEVER coming off

Ya ought not talk to the boy like at

Which, as it turns out, is masterbation. Because "the next guy" will inevitably be *you*!

I prefer to Ugga Dugga it on with my big Dewalt cordless impact!

Gotta get that hella good leverage 😅

I'll be calling you next time I need an oil change! My sh*t ain't gonna leak!😅

Always hand tighten Plus clean off and put a little oil on the seal

Minumum 4' long too. Weak ass 2' breaker bar 😂

Really?

😂

-need *get

Luckily these engines only last 2 oil changes so all is good :P

Spot on statement.

Exactly

Better than a fram or a wix.

Even man filter is ehh. Amsoil only

@@2seep Mann filter is the best. It's also OEM for most German cars.

😂😂😂😂😂😂

WTH you talking about 😂

😂😂😂

Man u r very far away😂

Brilliant !

Breaker bar! 😂😂😂😂😂😂😂😂

A rattle gun.

@@boosted. 3 or 4 ugga ugga"s?

He should’ve used an impact gun

With a leverage pipe on the end. It's important to get it tight😮

Facts

Okay , well what did he do wrong

​@@tallonhyde320he torqued the eff out of the filter

@@Straight_White_Fatherly_Figurebetter than it being loose

@@Huda88754 either way it sucks

And spark plugs 😢😮

Threads stripped and the head sheared right off… RIP motor…

He used the welder to make sure that the drain plug was tight enough

I always strip the head completely off the plug whenever i get a new car. That way no dummy "mechanic" takes it out to try and scam you with a blown engine once you leave. FACTORY OIL IS BETTER THAN ANYTHING YOU CAN BUY AND DOES NOT NEED CHANGED!!!! OIL CHANGES ARE A SCAM.

All the ugga duggas.

Yea but in my shop we torque oil filters to spec. Hand tight is still mostly safe but you CannoT hand tighten a diesel filter unless you got Shaquille hands.

Yeah 100% same

That's the proper way. I lubed the rubber gasket, then hand tightened all of my oil filters.

Had tight then 1/4 turn more with with wrench

😂😂😂😂😂

150 seems a lil light I prefer the 200 pound range really make sure it's seated

😂😂😂😂

You forgot to use torque to yield at 110 degrees after initial torque of 150 foot pounds.

That too. Lol. Didn’t notice. Lol

Yeah, that's not coming off. An engine swap will be easier. 😂😂

Not on one piece.

i had to change the oil in a 86 trans am anniversary edition. the owners said they never changed the oil since they bought it. 4 years later im twisting the drain plug in the side of the steel oil pan. it wrinkled up like a drag tire. had to lift motor up to drop pan to put new pan on.

not without an air hammer!!!

You hit the nail on the head.

3/4 turn past gasket contact

Up to the face and a half a turn, snug., you talk nonsense. Do not use a tool to tighten!

Crushed the gasket by overtightening

What the hell is a rurn?

Nice....unless your a great President then they will make up and pass laws that like conspiracy, no crime committed but you may have thought about it.

No face no case

​@@imnothuman4769and Harvey Dent was screwed from that moment on....

🤣🤣🤣🤣🤣🤣🤣🤣👍

Looks like a VW/Audi 2.0 TSi so it will blow anyways

@@davidcaprio8919 exactly

Weird... Wonder why Honda provides dealerships with preset torque wrenches for their oil filters if you aren't supposed to use them 😂😂

It's the last one that you will be able to use cuz it probably won't ever come off again .lol😂😂😂

Ffs 😂

True lol

Didn’t lube the o ring …

It's why I still do my own oil changes at 71 years old. And any other maintenance needed

That is Walmart training!! Also don't forget to tighten the lug nuts to 140 lbs.

If he's an actual technician he shouldn't need to be trained, he should already know.

It’s an Audi 2.0T. It’s supposed to be torqued to 26nm.

You wicked. Lmao

Yea should be hand tighten

Stripped thread better than no thread

Thanks for the tip.... I didn't know about the half turn back😅

That's why you do the drain plug and the filter back to back, so you don't forget to do them both in pairs.

@@kramnull8962 For over 50 years I've always just stuck my finger in the oil I just drained to coat the rubber seal on the new filter.

😂 yeah that'll do it, I've never put an stp filter on my car and I never will

Correct!

STP filters are better than Fram filters.

my first thought too

Also didn't pre fill it before putting in on

Lol!😂

😂😂😂

You forgot he was supposed to add on a couple extra uga dugas on the end really make sure the filter is seated

WRONG

you missed that he did not lubricate the new filters o-ring

@@kevinpark1 He did, he just cut it out. You see when he goes to put the new filter in that his fingertips of his glove are dry/clean but then it cuts and his finger tips on his right glove got oil on them. Not sure why he cut that part out but he did do the o-ring.

Some filters require a final 1/2”-3/4” turn with a wrench after being hand tightened and always lube the o-ring

Can confirm

I know that’s right

😂😂😂😂😂

What an asshole

😂😂😂

Haha lol he is who the hell

Looks prettier that way lol😅😅

I recommend 20’.

LOOOL!!!

😅😅😅😅😅😅😅

😂😂😂

I have always used staples

What the fuck

Ugh......what did he do right???

forgot to impact it on and the sump to 250nm

​@@insertnamehere5660You should use locktite and impact wrench on the oil drain plug as well.

@@Zoroaster4 dont forget the most important part, take the rocker cover off and put lots of chocolate spread over the cam lobes

These are the ones that make everyday a challenge 😂😂

The filter is supposed to be tight but hand tight, not wrenched on so much...

Well wrenched on for some could be hand tight for others

Filter color has nothing to do with it!

Did not oil the seal. It is a cup so it needs to be tight when putting it back on.

Only Chuck Norris can do that.

He needs an air impact😅😅😅

Minus the gasket that just got squeezed out

And not lubed😮‍💨

That's funny, well said sir.

​@@hunterbrandon656re-watch & check out his oily R index finger. Either he lubed the ring or tasted the oil, to check it's vintage...

😂😂

❤

Dont really need a date. You should be replacing them every oil change. And before you go on saying ManUfAcTuEr RecOmMenDs 10,000 miles, no. They recommend 10K for PERFECT driving conditions which over 90% of americans dont fall under. We fall under extreme. And oil filters. Although claims to run 20K will really only last as long as the oil you have in your engine.

@@AlfieArmani In a perfect world you wouldn't care about a date but I put the date on the filter because you don't know where that vehicle will end up next and I have never bought a used car that had service records included.

@@dennise4163 you have a fair point. But imo if they aint comin back to me for repairs, than its not my problem if the next tech is a slopjob

Service stickers left the chat..

Never knew a modern subie to have a bmw straight 6 crammed under the hood from the factory, but I guess anything is possible

And used a "Stay Together Please " filter😅

​@raiderjohn9407 thats an audi...

That’s a good one. Thx. Stp

Stsyf

Not necessarily especially on semis

@@roblovely15 I do on my Peterbuilt.

He's a pretty girl, just not too bright. - Foghorn Leghorn

If fuses are bright they blow, your analogy makes no sense.

Fuck you for making me laugh, I’ve never heard that one before.

@@railroaded1991 - He's as bright as a BLOWN fuse. Duh.

@@AJ-jy6lb you mean he's as bright as a blown lamp. If you're going to use fuse which isn't bright in the first place, you may just as well use rock, board, paint brush, etc. Or I suppose you could just say he's as bright as a fuse since fuses don't glow.

😅🤣😂

And use the same amount of force when tightening lugnuts.

Good for man!

Clearly you never worked on a tsi engine before!

@shimon2476 clearly it doesn't matter if it's a spin on filter no matter what engine

@@jodycordell1972 if you have ever worked on a TSI engine you would of known that most of them don't spin on with ya fucking hands unless you have the grip strength of The Mountain and Eddie Hall combined!

It's always been 1/4 turn past hand tight.

​@shimon2476 Eddie Hall Will get you a like!

🤣 Now you ready to go muddin in the Bayou

​@@MrLeroyJacobhell yeauh!

Thats going to leek you need at least 450ft-lbs at least for the next tech will be so happy same as the sump plug but make sure you round of the plug it stops amateurs from doing a bad job,and don't forget to put the old crush washer back on,when you put the new spark plugs in use an high impact gun you don't want those babys flying out of the holes. Jobs a gooden.add an extra hour on the as a good tip you have earned it 👍🏻🇬🇧

Someone debunked the oil tip. Even when wiped clean there is more than sufficient residue to stop the seal from binding and kinking. That said, old habits die hard, I still do it 😂

My man … exactly

He isn't an engineer - he's a fitter and a poor one.

But we don't know how much pressure he applied TBF, it could be in spec and that would be unusual because most people would make it snug regardless.