If you like my work, please do consider subscribing to this channel.Thank you. kzfaq.info/love/58DFky5Fm9AxH9UmWHHYmQ

Another way to improve the full bridge rectifier is by adding capactiors to each diode, I was reading about the "Graetz bridge rectifier".

Hello sir! I followed step-by-step as you shown in the MATLAB but I could not get the same results as you. Could you please help me?

u are the best man i learned a lot from every your video I want them a lot

Great work. Just want to find out if it is possible to use any other current for the current control. If yes, how will it affect the control loop?

Thank you for the video, but I don't understand the logic in the current sensing. You create a current reference which is in phase with the grid voltage, but you compare it with the grid current in the reverse direction - the inverter current, which is out of phase with the grid voltage. This will force a regenerative current, and will only work if the DC voltage is an independent energy source. How could this work with a passive DC bus?

Thank you for the useful information. I have one question - How do I calculate the inductance required at the input?

Many thanks for your time sir.

Explanation is very clear and when we simulate the same system with Matlab 2019A as per the data,the result is not satisfactory.it works good for voltage upto 400. More the voltage the AC-DC conversion becomes discontinuous and power factor also very poor. kindly fix it

@Tech Simulator You are a great teacher and very clear explanation you deserve appreciation. But there is no explanation about PLL Section can you help me? Looking Forward to your reply I am your subscriber plz help me i am in trouble.

you deserve to subscribe ur channel thank you.

Thanks for your clear explanation. It was a great help to me that I learned from your channel. Could you please explain how we can define the Kp and Ki for the DC voltage regulator?

it really really really help full, the first time I watched fully clear explanation. thank you so much..could please give an explanation on 3 phase PWM rectifier???

Great Explanation🧡

Sir, in this video you didn't mention kp and ki values of PI controller for PLL Control part, could you please mention it

Why the constant 400 v is given as a negative input of error signal ? Usually desired set point will be in positive input right ,is there any specific reason for the negative input?

Sir here which type of pid controller is used?it is Zeigler Nicholas method or other?

Hello sir, I followed same method but didn't get the output as yours, kindly guide me because it's urgently needed for my project submission 🙏🏻🙏🏻🙏🏻🙏🏻

Sir, I have one doubt, During rectification mode, how Igbt will turn on? Because Ac supply is connected to Emitter of Igbt. I am not able to understand this. can you explain Mode1

Bro could you please clarify about how do you get current reference after the PI output and cos wt .what is the relation ..please describe it

Is it possible to do reactive power control with that model?

But , the grid current wave form not look like sinusoidal

What is the range of VDC ref?

How did you find the controller values and R,L,C ?

Still third and fifth harmonic compoments persist in the system even though the THD is within the limits

Sir,thank you for posting this video.Sir,how did you select the values of Kp and Ki in PI controller and Kp,Kr,Ki in PR controller?Can you please share the details which will be helpful for us.

Thank you sir for the video. What differences are there if i need to use the same pwm converter acting like an inverter sometimes? For exemple, in regenerative braking's application, when we need to return power to the grid. Thank you.

Active rectifier is the same as regenerative ?

I don't understand why you control the phase to phase voltage same phase with the phase current.

Bro i am getting huge currect ..but pill is ok but currect in 500 amps with ocilation why i didnt know

I am getting 0.8V at output. What might be the problem?

sir how to decide the value of reference voltage in controller as 400

Sir, Please provide the reference paper 📄 I'm working on thesis written please provide me reference so i can use it in submission process. Thanks

Sir how you have calculated all these please provide the references

Sir ,Please tell us along with values, how values are taken? Without understanding it is meaningless!!😭🙏🙏💔💔

What are the values in the PLL section? Thanks and regards

In single phase grid inverter u multiply with 1/400 to get Vref but not multiply in this video why?

This is which version of Matlab sir??

Can you please provide the simulink file of this in description Or can you mail it?

Can i u show the igbt configuration

Sir,how are you selecting the sample time .eg: 1e-6 0r 10e-6 or 50e-6

I am unable to get PLL values,,i also watched your PLL video,,but getting different output please help😪😪😪😪😪😪

Could i have the m-file of this project

Can you please do a video on dual active bridge converter. or please give me the link if you have done one

Respected sir, Please provide reference of active rectifier. I need to write the equation in my IEEE conference. Please help me out

hi i need the slx file pls.

My model is not working,Sir can you check my model I will send on your mail my model

What is your mail ID sir?

Hello sir! I followed step-by-step as you shown in the MATLAB but I could not get the same results as you. Could you please help me?