Thanks

Thanks bro

Location ?

FROM .25 TO .50 YOU WONT SEE MUCH DIFFERNCE BUT FROM .25 TO 2.25 THEN YOU WILL FEEL DIFFERENCE

Sorry bro I don't have sleeve dealers who can provide ......

Yes

Yes it's good

They are good only bro you can use it but don't expert the same quality like original once.

@@MotoGod hi

Thanks for your support bro 😊

The only difference is of the life of the cylinder, other than that no much difference. Now I see people complain that Goetze blocks give bad pickup and all but that's an utter rubbish, pickup depends on many factors, like proper tuning of the carburettor, clean air filter, condition of clutch assembly and the pickup coil, clean spark plug, condition of sprockets, proper functioning of the 2Tpump and oil flow inside the cylinder, etc,. One more thing when it comes to Goetze cylinders is proper chamfering of the cylinder walls and ports using port maps and last but not least proper lapping of the piston and rings to be set properly and one thing to be mentioned if any of the things are not done perfectly the bike will not perform the way it should, which in my humble opinion ,a Good mechanic either from factory of Escorts Yamaha ( like in my case), or a trained mechanic can do. One more thing is strict following of the run in period once the cylinder is done and plugged in the bike. Believe me I am running two side by side one E2 and another Goetze. No difference; condition : all of the above mentioned things must be "PERFECT"

@@sohamsinha3631 thank youbro

I don't have better information on that topic so kindly visit your nearest lathe and ask them ❤️

I'm Good Bro 😇 Same Happens with all RX series it happens with my 135 too With pillion it Won't Feel confident to ride

@@MotoGod Thanx for replying bro, but u didnt answer my question. What if the lenght of the rear fork is increased by putting a 2-3 inch longer fork of another bike, along with increasing the length of the chain & brake rod, putting another chain cover, extending the rear mudguard, etc. I think this will shift the weight of the pillion a bit in front of the rear wheel and increase a bit more weight on the front wheel! I hope u get what i mean to say. If u dont get it, c how dirt bikes r altered which r used to climb very steep inclines. I just mean to do the same but on a smaller scale. This alteration is not that major but if it is done correctly will make any rx very stable to climb uphill with pillion! Pls reply.

No if you increase the height of rear shocks and all other mods still with pillion the front wheel will pop up and if you do all these mods the bike loses stability.....(the frame is the issue we can't do anything) what ever you do still the weight won't distribute to front in rx

No it won't

yes you can .75

2k-3k

Thanks bro..😃

Message me on Instagram (_motogod_)

Get it Checked Bro

Check cylinder piston clearance

I-1, I-2 series

Direct Fit But Its Difficult to get one in india

Don't listen to this puncture puttar, RXK carb is a direct fit to the rx135 and you can order it direct from Mikuni. The problem is jetting and if you don't happen to have a trained mechanic at hand, you can face a lot of problems. What I suggest is, get a properly trained mechanic and not a puncture puttar who claims to be a mechanic and try different jet sizes on your current carb. You can order different sized O.E jets from Mikuni. Don't ever use Natco or some other shitty brand jets in your existing carb. There is a reason Mikuni have existed for more than a 100 years. However I would suggest this upgrade only if you have ported your bore and have an upgraded CDI. To put it simply think of your mouth as your carburetor and your food pipe as your ports, if the ports aren't big enough no matter how much you put in your mouth, the food will be restricted by your food pipe.

I want Rx100 curb

1mm

U mean 1.00 is that correct?

That's why I said

Sure bro I'll do it very soon

Thanks for suggesting it to Moto god.... i want to know see and know more about RD 350 👍😁

Wait for first thousand kilometres

check it by opening the bore or check it by your mechanic

Crank, con rod, bore, head, piston, wiring, CDI, coil plate assy, and magnet, sprockets, carb, manifold, power box,...

@@MotoGod bro u missed the rx 135 monogram thats major 😅😅😅

If you install a sleeve .... then you completely messed your cylinder block ...(don't do it)

@@MotoGod bro I am having some doubts bro.....I want to ask u.... How can I contact u bro..... Because I need to do engine work so only

@@MotoGod instagram?

I don't Prefer Both Get Used Block.

@@MotoGod Tqs bro

Goetze piston

@@MotoGod thanks broo

Message me on Instagram (_motogod_)

No bro not available for sale

Kaveri Spare parts Kolhapur may have aftermarket ones, check with them

Goetze

@@MotoGod is sam company there bro

Don't know bro

@@MotoGod Thanks bro

@@mrkiinnu Don't listen to this idiot, Goetze and mahle are ok if its a 4 speed and you barely redline it. Always go for ART or Wiseco if you want performance and reliability.

Thanks bro for taking your time and commenting on the video Really it means a lot for me 😊

Informative if you want to f**k up your bike.

Thanks bro 😊

Over size the cylinder to it's max then the CC Will bump up

K

@@MotoGod but in your vlog you told that it's not good.?? Shall I do boring ?? Or not

Message me on instagram (_motogod_)

Ok bro

Glad it was helpful!

Sure bro very soon 😊

No

Thanks 😊

No bro not available with me

Yes its available 25 size

@@MOHAN_BOXER mobile number pls

Thanks bro 😊

Depends on how you ride it and on rider

@@MotoGod 60 km / hr speed bro

Yes you can ride it

Thanks 😊

😊

Cc is different and power output is different

Which is best for drive 100 km per day rx100 are Rx135

135

Thanks brother 😊

Apporx 3500

❤️

Video on ?

@@MotoGod on the banned dates of 2-stroke

Sure bro I'll do it very soon 😊

Thanks bro 😊 And Thanks for sharing your thoughts

Anytime bro ✌️

Don't listen to this idiot. Seizure only happens if your sleeve isn't pressed properly or if you have insufficient lubrication of if you have insufficient clearance between the bore and the piston and piston rings or if you have bad cooling or if the bore isn't honed properly or if you have metallic debris like rust from your fuel tank enter the combustion chamber. If all the above requirements are met then even the worst quality sleeves wont seize. The bore and piston will make a very rough noise but it won't seize. Again don't listen to this puncture puttar who doesn't know shit and is trying to preach people from the half baked knowledge he attained from another puncture puttar who thinks he is a certified mechanic.

Degree drop-out

Hi bro 😊

❤️

Sorry This Channel is all about English Content

Thank you! Cheers!