What is the best white for resin? Acrylic paint, ink, mica, paste, alcohol ink and Castin'craft
Рет қаралды 47,431
Күн бұрынHere is a look at how white pigments interact in your resin projects. I will be going over (and experimenting a little) using Acrylic paint, acrylic ink, White mica powder, resin pigment paste, alcohol ink and Castin'Craft - Cheddar will be chaperoning the tutorial as well -see you soon!
If you found this video informative and would like to buy me a coffee or leave a tip (cheers!): www.paypal.me/resinasyouwish
0:00:00 White Pigments in Resin
0:01:17 Acrylics / Mica Powder
0:14:35 Pigment Paste / Mica Powder
0:26:00 Castin'Craft / Alcohol ink
0:36:12 AcrylicPaint/Castin'Craft/PIgment Paste/Mica on Coaster backs
0:48:11 After the Cure
I am an Amazon associate; I receive commissions from the qualifying links to amazon listed below:
Acrylic:
Basics/Liquitex White Acrylic Paint: amzn.to/3vrhrgt
Dr Ph Martin’s white: amzn.to/3wCFxFh
Pigment Paste: Titanium White: justresin.shop/search?type=pr...
White Mica Powder: www.hippiecrafter.com/
Castin Craft white: amzn.to/3e0MYfB
Alcohol ink white: amzn.to/38ttAGZ
Typical tools I use:
Sizzix Accessory - Die pick: amzn.to/38SSgL8
Dental pic: amzn.to/2Gcj4tG
Dot tools: amzn.to/3s5JFMq
Paint spatula: amzn.to/3i88xNA Dental pic: amzn.to/2Gcj4tG
Torch: amzn.to/39suJiH
Heat Guns:
1. AmTake: www.amazon.com/Variable-Tempe...
2. Heat gun - I have a red version of this one: amzn.to/2WXGrwq
3. Heat gun - Green version: amzn.to/3woY6NK
Heat gun tips and nozzles:
Here is a link for just heat gun tips if you already have the gun but don't have the end pieces: amzn.to/2GPn3wC
Dremel 3000: amzn.to/3o4POra
Dremel bits Stone Bit: amzn.to/2NSyAvk
120 Sand Paper Grit Dremel bit: amzn.to/2BHns1Z
Tape: this tape is called “drape tape” even though the packaging is called painters tape (the guys ate Lowe’s explained why I couldn’t google it (LOL) amzn.to/2BxlFfY
Pink Respiratory Mask: amzn.to/3CLL7bP
Safety Glasses: amzn.to/3ERLamW
Safety Recommended: Carefully read your product labels and warnings, make healthy choices based on your research and craft safely!
My Shop:
www.etsy.com/shop/ResinAsYouW...
Pinterest: To see more of my designs and videos (Check it out)
pin.it/7qlAsgu
Resin I used: MiraKleer Table Top: amzn.to/2Zl9ziR
@ResinAsYouWish 3 жыл бұрын
0:00:00 White Pigments in Resin 0:01:17 Acrylics / Mica Powder 0:14:35 Pigment Paste / Mica Powder 0:26:00 Castin'Craft / Alcohol ink 0:36:12 AcrylicPaint/Castin'Craft/PIgment Paste/Mica on Coaster backs 0:48:11 After the Cure
@ellenjent4956 Жыл бұрын
Thank you so much for sharing different types of white to achieve different effects. I would have thought that just using part A of the resin without the hardener would have caused a sticky result, as the resin can not cure, but I love how it can be incorporated and still achieve positive results. I am a beginner, so your videos are invaluable in helping newbies learn how to use different mediums in resin.
@ViKee010 2 жыл бұрын
I can really relate to what you said about the alcohol ink. First time I used resin I wanted to see that drop effect in a pendant. So I added a drop of this and a drop of that with white in between then I applied heat for the bubbles and it got really hot on my art table. I mean I felt like I was in front of a fire. And it turned out that I was! It was completely invisible and I could not see any flames but I felt it and realized it was on fire! I hit it with my hand and then a towel. It went out but I learned a valuable lesson. The same lesson you are telling us about. But I will say that the pendant came out absolutely gorgeous with a rock looking appearance. If it were in a green color it would have looked just like a creek bottom. Anyhow I lived and got a great first piece. But be careful guys. I loved this video and learned a tremendous amount that I can’t wait to try out. Keep up the good work. I loved that you talked and you were really good at it. A great teacher. 🤟🏼🤍
@kertjans8794 2 жыл бұрын
Great video! Thank you for taking the time to do this.
@froxmere 2 жыл бұрын
Thank you so much for sharing this tutorial. I have only just started working with resin and have learned so much from this. I know the exact effect I want and now know which products will best achieve this. Also many thanks for showing your techniques, it’s very much appreciated and I am looking forward to experimenting with a little more confidence. I look forward to watching more of your videos.
@reneearriaga7485 2 жыл бұрын
A million thanks for this video!!! U taught me so much!!!! I’m relatively new and have been wanting to know all the differences between all of these products. U just helped me to clear this up! Yay!!
@samd7146 2 жыл бұрын
What a great tutorial, I’ve learned so much in such a short video, you’re a great teacher. Thanks so much 🙏🏼💕🍀
@Pashanny824 2 жыл бұрын
One of the best informative video on fine tuning and beginners alike. 🙏
@cindycimaedwards3688 2 жыл бұрын
Thank you! Best tutorial I have found!
@PennyTailsupStories 3 жыл бұрын
Excellent video, I am sure a lot of people are going to keep coming back to this one!
@LiveSleepResin 3 жыл бұрын
Thanks so much. This is very interesting and appreciate you putting this together.
@ashleyrich5345 3 жыл бұрын
This is such an awesome video, thank you so much! Your videos are always so in depth and very easy to understand and follow along with! As some one new to the resin crafting world, I really appreciate you making these videos! I am definitely going to try these methods, I also want to try doing snow covered mountains using this technique, I think they would come out looking really cool!
@erwinsenorin 2 жыл бұрын
Thanks a lot. Truly informative. I am a neophyte & have a pair of diy speaker box project which I've been contemplating to be covered with epoxy resin with a beach view upfront while black & gold on the sides. Am positively guided by your videos.
@angelarowland7758 3 жыл бұрын
Loved this! I learned so much, thank you!
@KennyFishbone Жыл бұрын
Awesome Awesome Awesome! Thanks for taking the time to explain this. THANKS for the safety tip about using alcohol ink.
@mandalasbypamela4087 2 жыл бұрын
Thank you so very much, this is extremely helpful & love Cheddar as well :) ! Much appreciated!!!
@janicehelmore-pouringwithf3360 3 жыл бұрын
Thank you so much for this experiment! I had wondered what the differences were. Each have a different kind of quality depending on what projects you are doing 🙂 💖💖💖👏👏👏🇦🇺
@Pashanny824 2 жыл бұрын
You’re great, and thank you for your videos.
@enewnum 3 жыл бұрын
Thank you for the information. It was really helpful.
@SeaHag11 Жыл бұрын
This has been sooo very helpful!! Thank you so much!!! ❤😊
@lauradrake1066 2 жыл бұрын
Absolutely wonderful test of all types of effects from different materials! I'm just getting started and this video was just what I needed to figure out what I need to purchase for what I want to do! Love your cat's input on the design! My Buttercream does the same thing!
@catherinegreen6594 2 жыл бұрын
Thanks for the tutorial it was very helpful as a beginner you save me time and money thank you very much I appreciate it it was a very good inspirational tutorial
@cindyreddoorartstudiogarre2229 3 жыл бұрын
That’s out of this world I have a commission piece to do for this lady and this was where I was having to work harder but now Thanks to you I will be able to work smarter thank you thank you...
@sarahhaakanson4289 Жыл бұрын
Thanks so much for sharing this! ❤
@apriln2108 5 ай бұрын
This is by far the best video out there. I super appreciate you sharing your experimentation. I know every resin brand may act different. You've inspired me to do my own experiments with what I have. And I've ordered some stuff so I can play ❤. Thank you thank you 🙏🏻!!
@tanjasart 3 жыл бұрын
That was educational. Thank you!!
@michellers1789 2 жыл бұрын
Thank you, I'll try different resins.
@stevechance4422 8 ай бұрын
Great video!Thank you
@Bestclipsof2024 2 жыл бұрын
Thank you. I am so new to this. I didn’t understand why I didn’t have cells in the past.
@lucyhawaii7475 8 ай бұрын
Thank you for the video
@TV-se4ce 2 жыл бұрын
Amazing good work 👏
@liletteautrey8481 2 жыл бұрын
They are all good in their way they are different level of the sea and he density of the ways
@mookzmom 3 жыл бұрын
I just loves me some Cheddar! Sending nose boops to him from my kitties. Love the tutorial here! I was told you could make your own paste such as you did, but that the paste then had to be mixed into some regular pre-mixed resin (A AND B) in order to cure correctly. interesting stuff, to say the least. I'm hoping to buy some part A just to experiment with my own pastes one of these days.
@ResinAsYouWish 3 жыл бұрын
Cheddar accepts your nose boops and returns them. I had fun giving it a try and will keep working with them
@lydiadevries8408 2 жыл бұрын
Thanks again
@annedibiase2980 2 жыл бұрын
Love your videos...but i wanted my waves to look less stripped,took me a minute before i switched my heatgun nozzle to the flat broad one and Viola! So much fun to watch and make! Very cool 😎
@birgitstech6619 Жыл бұрын
Thank you Christina for a great tutorial, I learned so much about the different tools of creating waves! I have just shouted you a coffee 💖
@ResinAsYouWish Жыл бұрын
Thank you! What a great compliment!
@birgitstech6619 Жыл бұрын
@@ResinAsYouWish 💖
@lauradrake1066 2 жыл бұрын
Cheddar Man is the best! Love him!
@Katiebugs_crafts 2 жыл бұрын
Love the video. Love kitty talking. Kitty: Mom what are you doing? Why is that more important then petting me? Lol love it
@henrynzube6672 2 жыл бұрын
The best
@zbigniewgrzywacz2476 2 жыл бұрын
FIVE STARS.. from Poland.. ❤️❤️❤️❤️❤️
@AngelOrtiz1 2 жыл бұрын
they all good it depends the affect you want to give thanks for showing us try with just silicone, WD-40, glycerine it will do for cells for whitening use industrial white powder is for molding resins or spanish powder in here clowns use spanish powder for makeup and melted white crayon stick good luck.
@lydiadevries8408 11 ай бұрын
Thank yoy
@oneluckygirlandherdog 2 жыл бұрын
Thank you so so much for making this video!! I have been totally struggling with beach pieces never having gotten one to come out like I want. But you have helped so much. Only thing that was frustrating was the fact that you're so soft spoken so I'd jack the volume up but then you'd turn on your heat gun and it would feel like I just stepped out on a busy airport tarmac and I'd scramble to turn it down or mute! 🤣 Just some feedback, I still watched from beginning to end, I subscribed and i hit the 👍... thanks again!!
@christinasettles6374 2 жыл бұрын
I love Cheddar!
@donnastaten1244 3 жыл бұрын
Great video- thank you for doing this. Have you ever tried the white alcohol ink Mixative? Wonder what that would do.
@d.debellis5091 Жыл бұрын
Your kitty is a talker! Great video, thank you. Did you paint your board first or use the colored resin and let it dry before trying this ?
@jacquelinecuriel6454 2 жыл бұрын
I love when our pets kids participate so don't apologize Cheddar is adorable (sorry if I misspelled its name) I have 3 dogs and soon I will start uploading my videos and most likely 99.9% of the time you will hear or see one lol. xoxo to Cheddar
@liletteautrey8481 2 жыл бұрын
I think in the mica only they is no titanium in it . The titanium is important in it . Just add a little bit of titanium powder in it and you will see the difference . For us here in Australia is about $41.00 per little bottle and it is very expensive for us.
@jennawolf9873 Жыл бұрын
❤❤❤
@honibzerko 2 жыл бұрын
Great vid I loved it I was wondering Casting Craft with Acrylic paint how that would work. Have you tried that experiment? Thank you
@terrimazzella7047 3 жыл бұрын
Why wouldn’t the paste you made change the ratio and make the piece not harden or be sticky? Love all the work you do and thank you for teaching us all your tricks!
@ImeldaFagin 2 жыл бұрын
Thinking about that too. Maybe try the homemade pigment paste with just resin in it added to some of the regular resin mixture.
@gretas61 2 жыл бұрын
Same thought, will it harden?
@jodimarie379 2 жыл бұрын
It ends up being such a miniscule amount of extra resin added to the whole piece.
@MaineCoonPride 2 жыл бұрын
Some resin brands are more ‘forgiving’ than others. Some resin ‘allows’ some differences in mixing.
@t.d.j.dejong6285 5 ай бұрын
It's oke, but you use the titanium paste and resin at 19:52 without hardner, so i still don't know what it's gonna do.... Also, when you leave the white stripe to settle for 15 minutes, and then blow, it will last better, they say. So i still don't know if the paste is good without hardner and if it's works at the end... :)
@littlefeather9709 2 жыл бұрын
Awesome video. Very in depth. I tried a ranger white a few days ago and it curdled like cottage cheese. I was very disappointed. Wondering if it was the brand? I've been using Amazing Amulite clear cast for resin. Any ideas. Do you know the longest working time resin? It seems 30 to 40 minutes is to short for me. Lol
@Kellye.with.an.e 9 ай бұрын
I use Alumilite too and was wondering the same thing.
@joselinerod8749 2 жыл бұрын
Thank you sooo much for the information. Like the different types example you posted It helps a lot for beginners.but I would like to know as the title said, what is the best white for resin because I tried with acrylic paint with resin and over time it turn to yellow. Watch videos and and some says you must use pigment and other says is the type of resin. Some are bad and makes yellow over time. Need some extra help
@ResinAsYouWish 2 жыл бұрын
Oh I see! Ok, here is what I’ve experienced about white yellowing. It has only happened to me with white acrylic paint if I overheated it with the heat gun and if I was using UV resin. All resin will yellow over time so I choose UV resistant countertop resin. I did an entire countertop for a hair salon (the white I used was castin’craft) and it’s been two years and there has been no yellowing. Keep in mind that UV resistant does not mean UV proof, all resin, when exposed to direct sunlight will eventually yellow. Also, some resin automatically has a yellow-ish tint to it when mixed, I would strongly encourage you to look at the resin you are using, not the paint.
@jmitorossian137 2 жыл бұрын
Really helpful vid. :-) Thanks! What type of resin do you use? Will both JR Art Resin and JR Diamondcoat works the same for this?
@ResinAsYouWish 2 жыл бұрын
Yes it will
@Otan62 3 жыл бұрын
I haven't done wave coasters yet, but have been wanting to give it a go.. so what I'm asking so what white should I use? Thank you 🙂
@rezinate1700 3 жыл бұрын
For me the question is "best for what?" Each kind has their purpose. Do I want cells in my waves do I want waves that look like they are being blown in the wind, or do I want it to look like the wave is deeper in the water? So then it becomes which white is a top white and which is bottom? Pastes are normally top whites and cell easier. Cast and craft is a top white but makes them look more wind blown unless ypu add a lot more heat or alcohol. And acrylic paint and micas are heavier so they sink and create a "bottom" wave. If you look at the acrylic paste and mica you can even sew how it is darker because the color sank down to the board itself. So when looking for a white, have an idea of what you are wanting out of your waves or project in general and ask if it is a top white or bottom white if it doesn't say.
@michellers1789 2 жыл бұрын
Super video, thank you! I have tried different additives of white to duplicate your waves/clouds. All I end up with is my white disbursing evenly across my piece, like an even layer of a transparent white. I have never achieved the distinct patterns, waves, lines, etc., and never a cell. Any clue what I'm doing wrong? Thanks a bunch.
@kim99may 2 жыл бұрын
It may be your type resin or you may have to wait longer for the white to thicken 1st. People have different luck with different resins.
@oneluckygirlandherdog 2 жыл бұрын
I have experienced the exact same thing, it's so frustrating!! At least I know now it's not just me 😀🙃🌻🇺🇲
@rezinate1700 3 жыл бұрын
For me the question is "best for what?" Each kind has their purpose. Do I want cells in my waves do I want waves that look like they are being blown in the wind, or do I want it to look like the wave is deeper in the water? So then it becomes which white is a top white and which is bottom? Pastes are normally top whites and cell easier. Cast and craft is a top white but makes them look more wind blown unless ypu add a lot more heat or alcohol. And acrylic paint and micas are heavier so they sink and create a "bottom" wave. If you look at your acrylic paste and mica you can even sew how it is darker because the color sanj down to the board itself. So when looking for a white, have an idea of what you are wanting out of your waves or project in general and ask if it is a top white or bottom white if it doesn't say.
@rezinate1700 3 жыл бұрын
P.S. most alcohol ink companies that have more than 1 white will normally have it on the bottle how deep of a white it is to tell ypu how well it drops other colors and this will tell you which one to use depending on what ypu want to get out of it.
@ResinAsYouWish 2 жыл бұрын
That is what this video encompasses - what is the best for your project and how they all interact in the resin.
@patricesparks305 2 жыл бұрын
@@ResinAsYouWish
@lynnecirillo6650 Жыл бұрын
@@ResinAsYouWish - Thank you for your time and experience - sharing this must have been so time consuming! You speak very well- Love your channel !
@mkfranklin2179 Жыл бұрын
What type of white is best for flower blooms. I fail every time, and I want so badly for it to work
@lindagatchell8079 2 жыл бұрын
Did you do your experiment on the 2nd coating of resin or first?
@janisbaker5873 2 жыл бұрын
Beautiful! Thanks for sharing! I’m wondering if it’s safe for the cat to be inhaling the resin fumes? I heard you say the garage door is open though
@helenamirian908 2 жыл бұрын
And how many hairs get in the resin?? :)
@cayleeb2596 Жыл бұрын
I did some beginner projects in 11 months ago and all of my projects yellowed. I used Art Resin brand. They told me that it could yellow because I used titanium white paint. Have you had this problem?
@chevarie2008 Жыл бұрын
Does the top clear coat have to be completely dry before adding the white?
@lindagatchell8079 2 жыл бұрын
Do you mix the castin craft in part A first or after you mix a & b together? TY
@ResinAsYouWish 2 жыл бұрын
Fully mix the resin so it’s ready to use, I add the castin craft to a little cup, pour in resin and mix until it’s the color consistency I’m looking for
@lindagatchell8079 2 жыл бұрын
Im trying to get a solid milk white color on a project im doing. Is it better to mix acrylic paint in or mica powder?
@ResinAsYouWish 2 жыл бұрын
Solid milk white would be acrylic paint, resin paste, acrylic ink - Mica powder is sparkly so it would look like milk
@lindagatchell8079 2 жыл бұрын
Just tried again with your castin craft alcohol ink technique, now they look like clouds :( Did I use too much ink? I wonder if my heat gun is messing me up??
@julierathe6661 3 жыл бұрын
When you made your own resin paste you did not add it to your resin, so how can it harden without the hardener? If your going to use it like your other pastes you still need to add that to your cup of resin like you do your other ones. ?? How can it dry or harden without harder Parr b??
@ResinAsYouWish 3 жыл бұрын
HI, yes, I didnt do it correctly, but mine did harden - I will be working with it more
@maureenkoback4406 11 ай бұрын
Question, on board two and the second example which was making your own paste (part A Resin and paint) how is that going to cure with no hardener?
@ResinAsYouWish 11 ай бұрын
Once you make your mixture- you should use it to color mixed resin - I didn’t do it right in the video 🤣
@rudymejia5042 3 жыл бұрын
What were the base colors you used for the boards. I missed that.
@ResinAsYouWish 3 жыл бұрын
I didn't include the colors on the boards for this video, but you will find them in the video description here: kzfaq.info/get/bejne/bseXitaouNKbc2w.html
@GenieCruz 3 жыл бұрын
Im confused! So you can mix part a with paint and it cured without the hardener? The other putty was mixed with part a and b though. I want to try this now!
@ResinAsYouWish 3 жыл бұрын
I’ll have to do a video of experiments with this. Resin comes in two parts usually - one part is resin, and one part is hardener. I used the resin (which for me was part a) mixed with color - then used as pigment paste. It was too thick in this video but hardened just fine 😋
@GenieCruz 3 жыл бұрын
@@ResinAsYouWish tjanks for the input. I went straight away and tried it. Wayyyyyy better result then my first beach waves and i thought my first ones were good. These are magnificent!!! Waiting for a full cure so i can demold and admire my work Thanks again for this awesome video
@GenieCruz 3 жыл бұрын
@@ResinAsYouWish ok so mine cured but only on the spots where the resin encapsulates it. I had to do a top coat because of the stickiness but when I demolded, the sides of the wave that were exposed weren't cured. It was like pus seeping out of a pimple. I'm just going to buy the pigment paste or if I use this methodI'll have to avoid the sides😉
@rosesweet1967 2 жыл бұрын
The pigment paste that you made, you don’t mix that into a resin mix before adding it to the project your working on?
@ResinAsYouWish 2 жыл бұрын
I totally did it wrong in this video - it did cure for me , but in the discussion afterwards I realized the mistake, after making the paste, you SHOULD mix it in resin
@anireyes4464 2 жыл бұрын
Please please can anyone help me. Cant make the cells in my waves. Getting frustrated
@jonathanveliz6191 2 жыл бұрын
hello how long should you wait to start the waves, thank you
@ResinAsYouWish 2 жыл бұрын
I don’t wait, I mixed the resin and started the video 👍
@janisbaker5873 2 жыл бұрын
What would’ve happened if you dropped alcohol ink into the resin cup
@FolleDart 2 жыл бұрын
Merci pour ce tuto c'est bien dommage cela ne se traduit pas en francais j'aurais aimer
@lindagatchell8079 2 жыл бұрын
Hi there. I am having alot of trouble with waves on my 4" coasters. What product do you reccomend? TY
@ResinAsYouWish 2 жыл бұрын
For the waves - in my videos I find success with castin craft mixed with a few drops of alcohol ink, and I also get good results with just resin titanium white pigment paste. You can find links and more helpful information in these two videos: kzfaq.info/get/bejne/gZqGpbR9v7ewiY0.html and kzfaq.info/get/bejne/rc6eotJ90MnPqps.html. - hope this helps
@beaswingle9065 11 күн бұрын
One more thing that is a beautiful cat and if you love him, leave them out it’s not worth it. Maybe that’s why I lost my otherDad. i’m crying now just thinking about it. Maybe the resin killed him. I’ll never know but he was puking. Just like this one this one is much better and I’m gonna keep them around for a while.😊😊😊
@beaswingle9065 11 күн бұрын
I couldn’t figure out why my dog was so sick all the time it cost me hundreds at the Vet and I found out by myself. It was having him in the room. Resin was making him sick. He kept puking. when someone left it in a video I was watching about animals getting sick from resin. I shouldn’t have him in the room with me. 😢
@beaswingle9065 11 күн бұрын
I used to have my cat and dog in with me not no more. They said it’s not good for them to be breathing in Resin OMG 😱 I didn’t think of that I get sick from it I can’t imagine hurting my Animals no was now there out of my art room 😢😢😢
@kawythowy867 Жыл бұрын
I am allergic to resin. If it touches my skin or if I smell it fumes I itch all over my feet snd hands. Be careful with that stuff and your kitty too.
@bertalev2010 2 жыл бұрын
Why are you not wearing a mask? I'm scared to work with resin without mask for eyes and breathing
@ResinAsYouWish 2 жыл бұрын
Hi, I was doing it with the garage open - the area was well ventilated
@utubbabe1234 2 жыл бұрын
an hour video?
@oneluckygirlandherdog 2 жыл бұрын
Yup, and a VERY VERY helpful hour long video at that!!
@lydiadevries8408 11 ай бұрын
I know I just rescued a kitten
@beaswingle9065 11 күн бұрын
He’s waiting to get out of that room because it’s killing him. That smell is bad. I didn’t realize.😮
@julierathe6661 2 жыл бұрын
I didnt think resin was safe for pets to be around.
@ResinAsYouWish 2 жыл бұрын
My understanding (I asked the vet) the area should be well ventilated, which mine is. Epoxy has three states, uncured, cured and powder and only cured is safe. It’s the most toxic when you heat it. I usually kick him out of the room if I can’t open the garage or I’m sanding - he throws a tantrum on the other side of the door every time - this also why you hear him yelling through the cat door more than you see him 😹
@voncieletaylor8621 10 ай бұрын
Talk louder don't whisper my phone is on high volume!
@arlisshuston4203 2 жыл бұрын
i find your tutorial helpful as was intended but darn,so many commercials and you want money to join,there are alot of people on here who do as well in the teaching department but do not get carried away asking for money here and let alone on a video,im only one board in and have gone thru 4 commercials already,so tho i would of liked it a whole lot better,i cannot watch someone so focused on money rather then art.i dont mean to sound disrespectful but the amount bothered me so much that i felt the need to comment tho i really dont like sounding mean,please dont take it that way,anyway ty for showing the differances and i had not used the paste before,i shall try it now tho.
@ResinAsYouWish 2 жыл бұрын
I'm not offended, but there are things to know about this. Firstly: My videos are really long, that is why KZfaq inserts commercials on the breaks - so it's mostly because we are looking at an hour long video. Secondly, I don't make enough money on KZfaq to break even on what I spend to make the videos. I do this because I love it, not because it makes money. I have a full time job so all of this is done in my spare time, including the hours it takes to record, edit and post. I'm truly sorry that the commercials were an unhappy experience for you.
@arlisshuston4203 2 жыл бұрын
thank you for tthe reply,i really dislike leaving disparagin remarks,but you tube on the whole has really taken the commercials to a really high ceiling,as a watcher when you find a tutorial that you really like,it seems at the worst moments you have to break,i know i could pay more to have commercial free videos,but,i also am astrugling artist,been doing resin for over 15 yrs,when most of the resins yellowed,ha,and wont pay for addless,,,i enjoyed your video,and subed,it seems i still learn things after all these years,again,ty for not being offended,lisa@@ResinAsYouWish
Resin As You Wish
Рет қаралды 47 М.
Nita's Fluid Woodworks
Рет қаралды 52 М.
Khabar SPORT
Рет қаралды 370 М.
Glitz N' Glitter By Michelle
Рет қаралды 3,9 М.
Resin As You Wish
Рет қаралды 78 М.
Daniel Cooper
Рет қаралды 73 М.
Bouncing Off The Walls Resin Art
Рет қаралды 2,6 М.
Moonkusser Art
Рет қаралды 33 М.
Glitz N' Glitter By Michelle
Рет қаралды 5 М.