Short and concise, this is exactly what I needed as I’m new to the hobby and my esc and motor came completely unlabeled

You are byeauoottyville man. Easiest explainations. I could learn 7 years of college in one day when your teaching.

AWESOME, YOU JUST ANSWERED MY QUESTION. I WAS STARTING TO THINK I GOT RIPPED OFF LOL. *SUBSCRIBED*

Great video once again 👊!!! These bench vids are loaded with useful info for the RC masses. Just had to do wire swaps with 2 new motor ESC combos. PS, digging the 4092 1480kv Hobbystar. Just had to gear up a bit, but torque is great paired with the Hexfly Hex6 8s version, running 6s. 🤘🤘😎💪👊👊

Thank you for being straight with your answer and not click bait

I wish everything was that easy! Thank you

Straight to the point and answered my question. Thanks!

Very helpful. Thank you.

Perfect!

Good video thanks

got to love 3 phase.

many thanks

Beautiful

Thank you

That was a good explonation. Thanks allot. Gretings from norway. I all cabels in black so l was thinking allot.

good video, picked up a Holmes Hobbies Revolver 2 and a Mamba X esc and the Revolver had no information online or in the packaging.

What are these cables called? I’ve been searching but can’t find anywhere. My Esc to motor cable snapped on Erevo 2.0 please help me find the name of these holed connectors

Perfect

Thanks

I am new to the brushless motor hobby. I was told that I should be careful about how long the cables are between the battery and esc and the esc to the motor. Is there any kind of formula for that? I see when I bought the motor that the directions said it was OK to shorten the cables on it. What is the rule on that? What is your thought on capacitor packs? Thank you in advance, Bill

A vid on sensored motor wiring would be good. Those are where headaches start

Thank you for your video. It helped me understand how to make my two motors go in opposite directions. I do have a question, though. I understand regular two wire power, but what is the third wire for?

I just wanted to add and I'm pretty sure you know to maybe forgot to mention Center wires on both the motor and ESC always be connected the yellow wire sometimes not always the yellow wire but whatever the center wire is on both the motor and ESC should always be hooked up and then like you showed you can either have it Go counterclockwise or clockwise by switching the outside to wires which would be a and b. I don't know hopefully that helps also great video

Great video but I don't understand what is a sensored motor as opposed to a non sensored motor? Thx

Ty

I Love Your Videos Buddy ❤ I have a new castle brushless esc but so want to run my old brushed motor since my 7 year old drives it too. Can you tell me which of the 3esc wires I connect to my old brushed motor Please 🙏 😇😎🌄

thank you. I was little scared while plugging my motor to other esc without knowledge of wire color... I saw "little smoke" and then i disconnected all of wires real quick... maybe iit wasnt smoke from wiring, only dust?'

i was taking apart my rc car and putting it back together because I needed to remount the taped parts. I misplaced the a and c wire with each other and tried to run it a couple of times (no more than 4) before I realised the issue. I switched them back. Could this have damaged my motor or esc? I have a sensored brushless motor btw

HI, GREAT VIDEO, THANKS. CAN A 500 WATT, BRUSHLESS MOTOR BE HOOKED STRAIGHT TO A BATTERY WITHOUT ANY OTHER COMPONENT? DOES A 500 WATT BRUSHLESS MOTOR HAVE TO BE HOOKED UP TO A CONTROLER? THANK YOU.

I have this bldc fan motor that has ( white, blue, yellow, red) from left to right. What are these wires and if I can hook up couple of them to a souce of DC to test it to see if this thing is any good which two wires should I hook my power to? I am assuming the other two wires, one maybe tachometer and the other probably pulse modulation. Should I be able to read some resistance between whatever wires or how does that work? Or should there be resistance between the two wires that go to power source. I hooked up the white and the blue to DC power and the fan did not run and I noticed current was really kicking in with hardly any voltage applied. So I disconnected. This thing goes on the evaporator of my fridge. I think this motor is shot. Shouldn't the fan blades spin loose and free without any quick stopping? When I hook up all the wires together or any two wires, the fan blade spin does not show any change? It says 9.75 volts DC on it.

Hi there! I'm fairly new to RC. I bought a Kyosho Optima Mid and a Kyosho Le Mans 240S brushless motor to go with it. I don't know which type of ESC I should buy to match the motor. Can I use a brushed ESC or does it have to be brushless also? And if you could suggest a brand and model of ESC that I should buy. Thanks a bunch for helping me out!

Sir can we use esc to other 12v battery

Sir, I have a motor fly with blue red and black. Currently the motor is rotating inverted. Which color can I changed to fix that ? Thank you so much

so, I'm trying to run a sensor less motor with a controller that has no hall sensor wires to the motor. It only has the rx tx and blue wires for the display. It's all hooked up and nothing. Should I try attaching the blue "display " wire to the blue phase wire?

Is damage guaranteed if incorrect a to c wiring on a sensored setup? Or just low rpm stuttering/cogging until fixed? Thanks

How do you hook up a power supply to brushless motors? I got some free brushless motors and want to test them and set timing and amp draw.

BUT with sensor type motors: is it possible to take a motor with sensors and hook it up to an ECS (meant for a sensor type motor) and hook it up to make it work? In general are all sensor type ECS's and all sensor type brushless motors compatible? Now, I've said that two ways. I want to have a discussion about how easy it is to work with (hook up) brushless motors. ON the ECS, what do each of those three wires go to on the motor (purpose)? That was a messy question - hopefully you can decipher the meaning of the issues at hand here.

I got a flytec 2011-5, want to upgrade with a water jet. Can I use the original controller after that? Or... what I need if already have the motor and the pump?

Ha....My motor has three black wires and so does the ESC. I'm assuming the middle wire of each go together, then I can connect the others and play around with finding the right direction and swap around if required...correct?

So, for a motor WITH sensors, how do you match up the phase and hall sensors, please?

what happen if I swap the yellow cable to blue?

I have the surpass hobby brushless motor 2030 and the esc is the traxxas vxl3m. And the motor wires are not colored and I saw it was going reverse, so i flipped it. And sudden the motor got so hot when its not being driven yet and the battery is a 2s lipo 2000mah and is the cause of it?

Hello, is it possible to install a coreless motor instead of brushless on this quadcopter board? Because the motor without a core has two output wires, but the motor of this quadcopter has four wires

What If I have a sensored esc and want to use on a none sensor motor will it work

I have a velineon motor but how to tell what wire is a b or c the colors are white black blue can you help please

I just need to know on a sensored what's a? (-) or positive? What's B and C?

How can I hook up a 3 wire hub motor to a victor 883 24 volt DC speed controller thanks

I always thought the middle one has to match up

Hey I was just wondering, does the dynamite tazer 3300kv 4 pole brushless have sensors or is it sensorless

I got a question Castle ESC sensored 6 wires how do I convert it 2 wires hobbywing sensored motor????

How to know the right thickness for wire please Thank you for your time

I got my motor to work but it starts fast then slows way down is it battery or wiring?

I have a bigger motor, a me-1306 BLDC. 12KW. Do you know a controller that will work with it?

On sensored, what is every wire of the sensor cable? Maybe we can swap those leads to match the direction on a reversed sensored...Please help :P

Can any brushless esc 2 wires be soldier to a brushed motor

How if you accidentally connect a to b, b to c and c to a

I own a GT Power Pro A60 and it's a ESC with lights engine sound Vibration and light kit and I don't know what is A,B,C

Can you do a video about your hobbystar 4092 1480kv motor please

Why does the motor connectors look different the esc

there r 3 wires coming out from the motor. which one is + and which one is -?

I'm kind of new at this what's a sensored motor like with a temp sensor in it

What does it mean when you switch the two wires out in the motor doesn't spin but when all the wires are hooked up normal and it spins in reverse

I have a 250w 24v dc motor for an ebike it has 3 contacts , how do I wire it to a motor controller that has 3 main wires and then 5 small wires 3 of which are hall sensors ?

I have a Drone motor with 3 wires all the same colour..which is the Signal wire....?

Excuse me sir and trying to connect a new motor and esc to my mini e revo

Noob question!! Where does the sensor wire from the motor plug into?

I have only two wire coming inside my house..... i have a problem in connection. And my baterry have only two outputs... i am confuse i cannot anymore...

How to fix lag in motor

Please if its not too big a pain

What is a non-centered motor? Is there centered motor?

Does the middle wire matter? can you fuck up your esc if you put your middle wire on the wrong esc output?

when i swap my wires round on my sensorless brushless motor i switch my thottle from normal to reverse so the car drives forward and it is so much more powerful, if i put the wires to normal the csr is slower . .does anyone know why?, cheers

How can I reverse the direction of the motor?

I have a brushless motor with 2 big wire's red and black and 3 tiny wire's Need to reverse the motor operation. How? Red and black go to circuit board with a relay three tiny wire's to speed control

Blue to orange! Lol, it's red not orange

Absolutely no help to those who don't have color matched or marked esc's

Thank you