To the people asking "why cut the wires and replace the leads"? The OEM replacement part calls for you to do that. The new "connector" has heat sensitive material inside that helps, more accurately, to protect the dishwasher. Apparently it was to correct a design flaw in the original engineering, where the bi-metal fuse wasn't blowing as it should when the unit overheated. The new connection is more sensitive, thus allowing the fuse to blow as it was originally intended. This isn't something this gentleman just decided to do on his own. The instructions that come with the replacement kit calls for it, and he was just following said instructions.

I replaced the fuse in my Whirlpool dishwasher last night and now it works again. These instructions are perfect. It's nice to be able to do this myself. I just saved a lot of money.

And this is why I love KZfaq. Thanks for posting!

Thank you so much for taking time to share this valuable video. It helped us identify the problem with our dishwasher and repair it.

Thank you so much Stan for posting this video! I was stressing out because we could not afford a new dishwasher and/or to hire anyone to fix it (ours is an older KitchenAid Architect Series II Built-in Dishwasher KUDK03ITBL) So I watched your video and thought I'd give it try. After weeks of dishes piling up, I found where I could get the exact fuse, and simply replaced it. I've never been so excited to see little blue lights light up on the dishwasher in my life.... Success!

Thanks for hour help. I followed your instructions completely. Worked like a charm. Saved me time and money.

thank you! this was exactly what I needed to fix my dishwasher. followed along and we got it working again.

Worked perfectly! Much obliged.

Thank you for sharing this! My dishwasher stopped working and it was the fuse which I knew how to access thanks to your video.

Great video Stan! Clear, concise, and to the point. Anyone who does not cut the wires but rather tries to use the old clips will be buying a second kit. I'm glad you emphasized that critical step.

Thank you for posting. This is helpful!

Stan Great job with Video and information. I replaced the thermal fuse and it is working perfectly. I did not cut the wires as you did because there appeared to be no reason to do it (even though the replacement part comes with the wire and connections everything looked clean). You are very much appreciated!

Thanks, video got me on the right track

With my GE Nautilus GSD2200G00WW dishwasher the thermal fuse was OK but one of two "interlock" switches had gone bad. Over time the contact had gotten dirty, creating a less than ideal contact surface which caused the switch to overheat and melt. On my model there are two of them, one in the neutral feed and one on the "hot" lead. Both were located in the control panel and actuated by the lever. $11 each (I replaced them both) plus s&h online. Your mileage may vary, follow all safety rules no warranties implied or expressed. Good luck!

thank you sir for good information

Great video thanks

Worked for me...thanks for saving me $$$

amazing thank you very much !!!

Thank you for the video. My diswasher didn't power up after a black out. After watching your video I felt empowered to open it. I found a lot of mini roches on the control panel and a lose connection. I cleaned everything and push the lose conection back in. Now my dishwaher works. Thanks

Thank you for the video. I didn't not cut the wires like you said I just replaced them all because thats what came in the packet. But you did show me how to use the o-meter to see if my fuse worked. Which it didn't. So thank you a lot

JJ I was thinking the same thing. He cut off the connectors, making replacing the fuse twice as much work.

My Fridgdaire DW (4 years old) won't start when we hit the start button. However, when we hit the delay start button for 1 hour, it works fine. Thoughts?

Hi mate . please do you have any idea about how to Install wiring diagram PCB Amika 6xl dishwasher

I have an MDB5651AWS model Maytag. Instrument panel lights and the machine were working intermittently but eventually stopped and now no lights and washer not working at all. The door switch is working but wanted to see if there is something else I can do before spending $130-$180 on another instrument panel. Other than the thermal fuse do you have any ideas?

Very good - thankyou - big help for me.

Thanks a lot!!! great video!!!!

Try this first, take the dish washer panel off and use some (do not use WD40) CRC QD Electronic Cleaner (Wall Mart under $5.00) or any electrical contact cleaner. TURN OFFTHE POWER BEFORE STARTING THE REPAR !!!!!! This may work on your garage door, microwave (worked on all three for me )washer, dryer , computer and any other circuit board and electrical connections Your contacts on your circuit board and wires may be dirty. So don't be stingy (it will not hurt any of the electronics) soak the connections and boards. I have to do this with my microwave (if you boil a lot of water) and I fixed my 14 year old garage door opener. Fixed my dishwasher today and it's over 12 years old. Not sure why no repair guys don't tell to try this before more elaborate fixes

I didn't have to cut the wires? Why would you do that? You can just replace the fuse!! It's all fixed and works great!! Thanks for the great tutorial minus the cutting the wires part ;)

Remove the wiring band inside the console. Spray with WD-40. It worked for me.

Thanks for the great info Stan! Despite the negativity below (I don't see that any of them has posted a helpful video on ANYTHING), I appreciate the insight.

Damn people. He is just showing how to fix.

Your video helped me figure out that my dishwasher fuse was dead. Thanks! But you said a bad fuse will read 0 ohms. I think you have that backwards? The way I test for a fuse is with continuity, if there is continuity then yes the fuse is good. When the ohms are 0, the fuse is good I think

The problem here may be underlying. As a mechanic, the question begs, why does a fuse blow? The obvious answer is an overloaded circuit or a short. Electrically, the same thing.

Why do the wires have to be cut? Won't the old connectors work on the new fuse? Thanks!

Why did you cut the connectors off? You could have connected them directly to the new fuse. Now you have three times as many connections to get loose. Don't cut wires unless you have to.

From where I can buy fuse in Mississauga or online.

i have a question my dishwasher was working and in the middle of a wash cycle the just stop.Now stuff keeps coming up form it.

The normal wash light flashes. Cannot get any other button to work When I turn power off and on again, normal wash and heat/dry option buttons stay on as they normally would be on. After 15-20 seconds, only normal wash stays on and it is flashing.

Mine tries to start hums a little, and then shuts off. Thoughts?

Kitchenaid dishwasher wouldn't start so I successfully did a reboot cycle of my Kitchenaid kudl03fvss0. When it completed it still won't start. Any suggestions. Thanks in advance.

I have a Haier countertop dishwasher. It fills and and empties. The cycle don't run. Help

Я так понимаю на современных ПММ отдельный предохранитель теперь не ставят или на плате распаивают. Кто знает подскажите?

At 4:27 we see that the new fuse has the same connectors, so there was absolutely no reason to cut the wires at 01:58. Indeed, at 01:37 he removes the old fuse from the wires, so why didn't he just do that to begin with, instead of cutting the wires off??

Why can’t you use the old leads to connect to the new thermal coupling or whatever it’s called??

Hi Stan we have a Kenmore Elite dishwasher model #66913943K010 purchased in 2011. Recently some of the lights in the panel have gone out although the unit runs but I have no idea what cycle it is on?? I believe it could be the thermal fuse you have talked about in this video but am not sure? We live in a rural area and to bring in a service tech is requires two trips; one to diagnose & order part, second to repair once part arrives! Expensive and time consuming if it is something I can do. Where to purchase thermal fuse to try that first, thanks!

thermo fuse uses connectors, why you cut off them then pull out the fuse?

Before cutting off the connections (terminal connectors) , just check the old ends & the new fuse to see if they match up. If so, no cutting and replacement of the fuse connections are necessary.

Why did you cut the wires and replace the leads? Makes no sense. It was the fuse that was at fault.

Anyone know what to do if the input valve functions fine but the machine is not starting. The light comes on but no water

Anything special about the fuse? Can you provide a link?

That first step is always the best. “Before you begin, unplug the - oh wait, my dishwasher wasn’t plugged in!”

i just installed a new control board and tested the unit but it only starts to fill then shuts down and the start button starts to flash and does nothin after that. its a whirlpool dishwasher

Hi, I bought the fuse online and replaced it. But still it won't start and no lights. Any suggestions ? please

No need to cut wires.

Every 3 weeks my dishwasher just doesn't turn on. I have to turn off the breaker....unplug the power to it replug it in reset breaker then randomly it works again for another 3 weeks....I wonder how I can troubleshoot this problem with a multimeter

my disheasher is making noise but no water us running through it

Lasted 1 week what now now power again. Anything else?

Thanks when I press the start on my KitchenAid the Child lock comes on .

Question: I have a GE dishwasher. Lights are on in the panel. when i press start i get light "Sensing" and nothing else happens? GE DISHWASHER MODEL GDWF100V55WW

I have a LG and can't find the fuse .?

You didnt say why you replaced the fuse connectors.

I have a ge dishwasher lights come on but won't start. Tryed unplugging it. Son opened it up all plugs are connected. Still won't do any thing. About 4yrs old used very little. Have tryed restating it. Help please

child lock blinking on kitchen aid dishwasher. Tried pushing energy saving button for 5 seconds. Didn't work and delay hours 2 light blinking,cancel light blinking I try everything not working

The power come on and the unit fills with water, but then does nothing. It won't run through it's cycle. Any ideas?

My dishwasher died but it is 50 years old! They don't make them like they used to.

video was good bud sadly only covers one of many possibilities of why it wont start. this did not help in my case

Don't forget to try other easier videos first before going through this monstrous hell, because the oroblem is easier to solve on those videos so you don't have to become an electrician and start tearing the machine apart. People don't want to have to do all of this and usually don't have to! Can't they design a good dishwasher that's as reliable as the old ones though? These silly motherboards cause nothing but problems that require resetting often when the red light goes on. The machines somehow reset to a 2 hour setting and then you have to figure out all over again to get back to your normal 30 minute setting which requires you to watch a few videos because there is no reset button. Also, I've only had mine for a couple of years and one of the rolling wheels under the basket fell off. Cheap stuff. I don't know where it is. Probably was on bottom of dishwasher and I didn't know what it was so threw it out. Where can people order more wheels? Do these dissolve with time? This wasn't the cheapest dishwasher on the market so I certainly expected better quality.

Nice hands, lol

S

That is only one cause. My Whirlpool Dishwasher control panel does not light up! There is power in the door , the Thermal Fuse has conductivity and so does the door switch. Does this mean the Motherboard is bad. Your title should be, "One Reason Why Your Dishwasher May Not Start".

this sounds stupid why cut connectors they just unplug?

+doityourselfstan, Why the hell do you cut the wires and go thru the whole process of stripping them etc, when all you have to do is pull the plugs off the new fuse and plug the old wires right back on????? That would only be necessary if the new fuse came with different size plugs for some reason, but in my experience that is not the case. Also, you stressed the point about making sure to match up the wires correctly when doing it your way - black wire to black and striped to striped - you do realize this is simply a FUSE, right??? It makes NO DIFFERENCE which wire you connect to which, LOL. A fuse is not polarity sensitive, the electricity goes in one side and comes out the other, electrons don't care what color the wires are!! LOL

Dishwasher is too new for this to happen.

power to fuse box doesn't need to be off. just unplug the dishwasher

wear shoes!

Consider changing the title to "What to do when your dishwasher has no power". Most people have a simple problem, not a completely dead dishwasher that needs such an advanced fix.

turn off the TV and take her credit card away.

What the hell...cut those wires? OMFG...get another job.

My SMEG ST6015-2 will start, BUT ... after about a minute it all of a sudden stops. It refuses to do anything else. It is not user-friendly; it is a piece of shit. Piece. Of. Shit!