Takes you through step by step how to set up diagnostic mode and what to look for on your whirlpool cabrio washer.
Пікірлер: 118
@venessacueva79252 ай бұрын
Thank you for Demonstrating the Diagnostic Modes. My washer would start and wash for alittle bit then I would get Flashing lights and the F was displayed. After doing your test The code was F51. I appreciate you making this video it made me feel relieved, so I'm able to tell the repair person. Thanks again.
@donaldwarriner16403 жыл бұрын
Huge help as I live in Mexico with limited language skills. The washer is relatively new so you've been a life saver.
@RickyPisano2 жыл бұрын
Have the exact washer as in your video and the matching dryer. Bought them in early '21 for $100 each and they were like new. Haven't had a single issue with either unit. I had no idea about this diagnostic test. Very well done video. Thank you kindly for taking the time to make it. I saw it was done 6 years ago and I would have never guessed the washer and dryer I purchased for $200 were that old. They're like new!! Not a scratch on either unit and both work fantastic. I guess I got lucky. Thanks again Mr. Wayne!!
@JaossRousin Жыл бұрын
Qq
@markiemarks45 Жыл бұрын
We bought the Cabrio (W10240441C) in 2009.Still working fine..Thank you for your video the diagnostic was well explained.
@SgtBooker443 жыл бұрын
Thanks for posting. I just replaced the bearings on mine and this is the final test and done.
@kirkfraser18732 жыл бұрын
Best video in this topic I've watched! Clear and informative, thanks!
@TheBlankenman3 жыл бұрын
Straight to. The point. Great video
@tiz77483 жыл бұрын
AWESOME VIDEO !!!!!! I NEVER KNEW THIS. I did have a repairman come 4 years ago and he said my rods were bad and he replaced them. It seems when I put alot of cloths in it will never complete . So i have learned to only10 to 13 items and it works I also never put my spin cycle on high, Cause when i do it always Seems to stop and I have to reset all over again. My washer did all the cycles you said. THANK YOU THANK YOU BIG TIME
@onestogie8826 Жыл бұрын
Finally the correct process to enter diagnostic mode. 🙂
@edwinjaehnig16993 жыл бұрын
Great video sir. Good and clear explanation. God bless you
@tishatisha36934 жыл бұрын
Thank you so much you are a life saver. Just saved me some money. Appreciate it.
@SamsungSmartWashingMachineFanАй бұрын
For Samsung washers, the detergent dispenser is on the right while the fabric softener dispenser is on the left in a drawer
@RonArcher7 жыл бұрын
Thanks for making this video, my machine was stuck somehow but, with no error codes.....running the diagnostic seems to have unstuck it and now its back to normal. :-)
@russdwilliamson2323 жыл бұрын
A BIG SHOUT OUT TO BEN THANK YOU FOR SHOWING US HOW TO WORK/ TROUBLE SHOT OR WHIRLPOOL CABRIO WASHER GOD BLESS W/H LOVE STAY SAFE
@mrcienfuegos20105 ай бұрын
thank you very good video
@hyde13134 Жыл бұрын
Great video. But am I missing something? How do I calibrate the machine. My problem is UL codes. I think I fixed it but I should recalibrate. Thanks
@staytight63402 жыл бұрын
Thank you Fixed it because of you
@ScreenPrintR7 жыл бұрын
Thank you. I have a different style but same brand (Whirlpool Duet Front Loader: Mod: WFW9151YWCO) With the power off of the machine, still plugged in, I hit, Delay Start, Extra Rince, and Cycle Signal. One right after the other starting with Delay Start. Did this three times and the error code appeared, LF. I than pressed and released Cycle Signal and the code moved to E1, F6 repeatedly. Still cycles through and doesn't stop. Thanks again.
@jakers11583 жыл бұрын
mine didn't go to done. It just beeped and went off.
@brittanyjackson43063 жыл бұрын
hello !! so i made it through the entire video and my washer has done every step so far except for hit "done" . its still on c8 and wont stop .. how do I fix that ?
@SamsungSmartWashingMachineFanАй бұрын
For the Samsung lid error, it is: dC error
@2008sfan5 жыл бұрын
my washer displays OL message, while the machine is not overloaded, what is the problem? Thanks
@SamsungSmartWashingMachineFanАй бұрын
For Samsung: during test it goes through them by one or two digits: 1. lid lock. Ho (hot water) Co (cold water) 6. Agitation. 7. Drain. 8. High spin test. 10. End
@wirelesmike735 жыл бұрын
No error codes and runs through test mode with no issues... But, still won't go through a cycle without stopping, draining, and coming up with oL on the display, even when empty. What could cause that?
@infocuscareers5 жыл бұрын
This is exactly what mine does!!!!! It's so frustrating!!! I will turn it to drain and spin...but not sure if my clothes are clean.
@berrypatch55833 жыл бұрын
Did you get yours fixed...just bought mine used and the same thing. Says ol and doesnt really agitate...fills spins and drains.
@spacepirate33123 жыл бұрын
Has anyone came up with an answer?
@wirelesmike733 жыл бұрын
@@berrypatch5583 The only thing that worked for me was running the Clean Washer cycle. After that, I ran an empty Quick Wash cycle and it worked. I'm sorry, I didn't get alerted to any replies to this comment until just today.
@wirelesmike733 жыл бұрын
@@infocuscareers The only thing that worked for me was running the Clean Washer cycle. After that, I ran an empty Quick Wash cycle and it worked. I'm sorry, I didn't get alerted to any replies to this comment until just today.
@carloschavez77332 жыл бұрын
This a gud one no lie 🤥 2022
@kennyyang25665 жыл бұрын
Here is all the error code: BUTTON Cabrio Washer Fault Codes Fault Code Washer Problem Repair Steps LF (F30) Long Fill LF flashes when the water level does not change for a period of time after the valves are turned on OR water has left the drum but control does not detect a water level change. Is the water supply connected and turned on? Are hose screens plugged? Is water entering the tub? If so, check the pressure hose connection to the machine/motor control. Ld (F32) Long Drain Ld flashes when the water level does not change after the drain pump is on. Is the drain hose or the drain pump clogged? Is the drain hose height greater than 96 inches? uL (none) Unbalanced load uL is displayed when the machine/motor control detects an off-balance load and remains on while the washer runs a mini-cycle to rebalance the load. Display clears if mini-cycle successfully rebalanced the load. If the mini-cycle is unsuccessful, uL will flash until the door lid is opened, allowing the customer to view and redistribute the load. oL (F70) Overloaded oL flashes when the machine/motor control detects a load size that exceeds the washer’s capacity. Open the door lid to clear display, remove excess laundry, then restart the cycle. Sd (F71) Suds Detection Sd is displayed when the machine/motor control analyzes drag on the basket and detects a suds-lock condition. It will remain on while the control runs a mini-clean out cycle. If the clean out cycle is unable to correct the excess suds problem, the cycle ends and Sd flashes in the display. This may signify: Excessive detergent usage. The basket cannot engage during drain step. Mechanical friction on drive mechanism, not allowing the basket to engage. Lid (F81) Open/Close Door Lid Lid flashes when the following conditions occur: User presses START with the lid open. User presses START after two consecutive machine cycles without opening lid. The machine/motor control cannot detect the lid switch opening and closing properly. Po (none) Pump Out (lid opened) Po flashes when the drain pump begins pumping out water from tub because the door lid is left open for more than 10 minutes. Close door lid to stop the drain pump. HC (none) Hot, Cold Reversed HC flashes when the hot and cold inlet hoses are reversed. Make sure inlet hoses are connected correctly. dL (F80, 82, 84, 85) Door Lock Failure dL flashes if the following conditions occur: Door lid is not closed completely due to interference. Lint and detergent residue is preventing the lock bolt from extending. Machine/motor control detects an open door lid switch when attempting to lock. Machine/motor control cannot determine if door lid is in a locked state. DU (F83) Door Unlock Failure dU flashes if the following conditions occur: Excessive force on the door lid is preventing lock bolt from retracting. Wash residue is preventing lock bolt from retracting and should be cleaned away. Machine/motor control cannot determine if the door lid is in an unlocked state. F1 (F60-68) Primary Control Failure F then 1 flashes when there is a primary control failure. Replace the machine control assembly. F2 (F2) Keypad/User Interface Failure F then 2 flashes when in: Diagnostics Test mode if a stuck key is detected. Standby mode if there is a user interface mismatch. F40 (F40) ATC Thermistor Open/Short F then 40 flashes when the ATC Thermistor is detected to be open or shorted. F41 (F41) Motor RPS Thermistor Open/Short F then 41 flashes when the motor rotor position sensor (RPS) thermistor is detected to be open or shorted out. F42 (F42) Heater Thermistor Open/Short (Not Used) F then 42 flashes when the heater thermistor is open or shorted. F50 (F50) Motor Stalled F then 50 flashes when the motor rotor position sensor (RPS) senses no rotation. Does basket turn freely? If not, make sure bottom shipping pack has been removed. Determine the cause of friction. F51 (F51) Motor RPS Failure F then 51 flashes when there is a motor rotor position sensor (RPS) failure. F52 (F52) Motor Stop Failure F then 52 flashes when the motor rotor position sensor (RPS) senses rotation after stop command. F53 (F53) Motor Control Overtemp F then 53 flashes when the machine/motor control detects high temperature for the motor module. Does basket turn freely? If not, determine the cause of friction. F54 (F54) Motor Control Overcurrent F then 54 flashes when the machine/motor control detects high current for the motor module. F72 (F72) Basket Re-engagement Failure F then 72 flashes when the basket check routine fails to determine if the basket is re-engaged after being disengaged. Is the basket floating? If yes, pump out water. See Long Drain. Does basket turn freely? If not, determine the cause of friction.
@kennyyang25665 жыл бұрын
What is the cause of oL= overload... Anyone has experience it?
@JamieHOTT134 жыл бұрын
What about LF?
@randilangley82747 жыл бұрын
during the diagnostic check mine would not go past C7 either. The pump continues to run as if it is trying t empty the water yet the washer is empty. another thread I read said that the main computer board needs to be replaced. I hoped that I would find a simpilier fix. replacing the main board sounds expensive.
@asiarankins56904 жыл бұрын
Mine stopped during draining. Back to showing F
@danielleschrader17224 жыл бұрын
Is stuck on C1 and is filling up with water what should I do
@noles61714 жыл бұрын
Danielle Schrader have the same problem
@abbasbehmanesh99644 жыл бұрын
@@noles6171 I have the same problem
@susanboggs48267 жыл бұрын
ok I put a new drain pump on. started the test. went thru c 6. then went to f21. now it's just running. it still will not do a wash cycle. help please
@hermanthomas15295 жыл бұрын
Susan Boggs c
@kennyyang25665 жыл бұрын
I follow your instruction. After C1 it dislay oL then the diagnostic stop. What to do next?
@gregosborne67557 жыл бұрын
I have one that started leaking water. Hoses look good. Tub seal mabey bad?
@Chryco_51266 жыл бұрын
the washer works perfectly but will not operate in any other mode than regular , no delicate etc , will this diagnose this issue ?
@ebonewillis84895 жыл бұрын
This is a helpful video. While doing the diagnose on my washer on c8 it will not actually spin, it only moves like in c7. Any advice on what it could be?
@@dariuscoleman2046 Thank you for your response. Now my washer won't do a damn thing it just keeps beeping at me. So I have a new issue to worry about. 😅 Got any suggestions for that?
@johncrick80744 жыл бұрын
Terrific video. Thank you for taking time to make and to post. I have some questions about what I am experiencing with my washer. May I co tact you directly?
@maryannkozlowicz66826 жыл бұрын
Any idea what can be wrong with my Whirlpool Cabrio dryer - the buttons all work but when I press Start it hums and stays in sensing mode without tumbling but it does heat up - what can be the problem? I can turn the drum manually and it doesn't feel like anything is hindering its ability to turn.
@cnoblot20116 жыл бұрын
Duet Sport HT Lavadora Diagnóstico, tendras otro video, mi lavadora en los ciclos de lavados no funciona, se le cambio la manguera de la tina a la bomba q estaba dañada, como le hago el diagnostico para saber si es el CPU u otra fall
@user-of5eq4yc7i Жыл бұрын
❤
@Yortanian7 жыл бұрын
the bleach and softener dispensers have a rush of water which seems to be way to much pressure and they overflow??
@precido5 жыл бұрын
Hi Mr Wayne my machine performs all the modes except C2-C4 ...what might the problem be?
@jamesalexander77245 жыл бұрын
Urgently need your kind assistance. I have a Whirlpool Cabrio. It shows "sd" error code. I would stop at the last spin. I have tried several times to use the bleach and clean cycles. Not removing the code. Can you please help. Is there a reset button or calibration function to see if this will go away? How can I fix myself. I called around and everyone is extremely costly during the holidays! Please help. Thank you in advance for your kindness. Happy Thanksgiving!
@o2good4u7 жыл бұрын
in the diagnostic check, my washing machine did not go out of C7. It did not drain in diagnostic check C7. What can I do to fix this?
@Youtuber-xs9cp7 жыл бұрын
Shelly Osgood Drain pump bad or clogged or drain hose clgged. You got a pretty hair by the way.
@griffon32756 жыл бұрын
now that was downright creepy ,,,next he will be asking for toenail clippings ?
@lindasolorzano5167 жыл бұрын
My F1 on Whirlpool duet sport front loader, turned off, and tried the pause/etc. What could it be? which component? bought it about 4-5 years ago
@sallytrulock63626 жыл бұрын
My Cabrio won't go through the clean cycle. Has anyone had this problem and know how to fix it?
@gabrielamares77665 жыл бұрын
So my husband bought this washer at a yard sale. So I tried it and when it's time to since again or spin it won't work 😒 so I turn it off then on and push start. But it usually turns off like 2 or 3xs so I just stand their till it actually starts working. Then to finish the last cycle I turn off and change it to drain and spin. I really don't like this. Someone help.
@shannonrekar94624 жыл бұрын
I have the same problem, both with my husband just randomly picking up a washer, to the error and having to reset it after each cycle. Have you found out anything about this? Google and KZfaq seem to be no help.
@tiz77483 жыл бұрын
When it happens to me I too restart it, powering off and on, But I also change the cycle from colors, or heavy duty whatever i change from whatever I had it on before, Till it goes and does what it was supposed to do the first time.
@leslyzepeda27014 жыл бұрын
my washing machine marks f2 and no button reacts what can I do?
@tcshy19039 жыл бұрын
Mine is not going into spin cycle. It drains and then starts running water again. Over and over. This washer is only 4 months old.
@cynthiae46528 жыл бұрын
Hi I just got a used whirlpool cabrio and I'm having the same problem as the people that commented before me. My clothes end up wet after the cycle is over. The water is drained but apparently the spin cycle is not completed. but if I set it to "spin and drain" it does work. Do you know what the problem is? and how I can fix it? I would appreciate your help.
@mechele381357 жыл бұрын
Mine does that, did you ever get an answer?
@cynthiae46527 жыл бұрын
No I didn't :/ I got rid of it and got a new one. I got word that they were made bad and kept messing up.
@user-oj7vw1we9f11 ай бұрын
I have the same problom
@johnchoe57804 жыл бұрын
My diegetic shows F70 how can I fix?
@acalabria19794 жыл бұрын
Did you figure this out?
@MrRicknavon Жыл бұрын
Diagnostic code went to c8 and stopped. Why
@guillermobatallameza58607 жыл бұрын
mi lavadora sólo entra un cuarto de agua y no más y se mueve mucho la rina y golpea a los lados
@WilliamHollinger20194 жыл бұрын
I sometime i get uL
@daniellenelson65353 жыл бұрын
stuck on 88 never did anything, any idea??
@Sam-cl7wq7 жыл бұрын
thank you!
@jackierussell67203 жыл бұрын
What if done never lights up after c9
@gendustriesofficial3 жыл бұрын
Wich Model Is It? - Model No.?
@truejazz2009 Жыл бұрын
Will not spin in c8. Stays on c8 forever
@louannkulpa42634 жыл бұрын
My washer doesn’t go past the c1 and has an error code of ol. What is wrong?
@berrypatch55833 жыл бұрын
Mine does the same...what was wrong with yours?
@jimharman35757 жыл бұрын
what does lf mean on my whirlpool cabrio platinum washer mean?
@lockyzeroone7 жыл бұрын
I have a Whirlpool Cabiro Platinum series washer. When I run diagnostic code, after C1 diagnostic it does not continue and blink time and start/ pause button. Any help will be appreciated
@desireevassar96943 жыл бұрын
Did you ever find out what was wrong? We were just given one & having the same problem. I tries running the test & it just stoped after c1
@lockyzeroone3 жыл бұрын
Yes, the problem was with the controller board. When I replaced the main board it worked.
@tomhofer2077 жыл бұрын
my washer makes a sort of loud click noise every time the washer agitator goes back and forth......why ?
@DJDevvin5 жыл бұрын
It’s normal it does that when it agitates.
@paulpauldavidson5 жыл бұрын
Washer starts, pours a bit of water, moves around a bit and then shuts off with "Complete" lit up.
@annettezetts56045 жыл бұрын
THE CODE I AM GETTING IS DU WHAT DOES THAT MEAN
@joefazo35192 жыл бұрын
done never comes on after C9
@joefazo35192 жыл бұрын
help
@gringowiththelingo15 жыл бұрын
Stuck at c8 forever on the diagnosis test 🤔
@neldajackson23146 жыл бұрын
I have a whirlpool cabriolet, washes fine but when rinsing and spinning makes a loud noise like a airplane flying overhead
@vrepair30703 жыл бұрын
Sounds like the tub bearings, replaced mine, and solved the issue
@rocco6x95 жыл бұрын
Hi I get a F1 and it doesn’t spin
@alecvip75626 жыл бұрын
I have a front loader though
@barbaraparsons62047 жыл бұрын
mine won't go to c9 help
@bernabeadamecanales95877 жыл бұрын
Porque no ponen las programacion en espanol
@yennissypaiz29347 жыл бұрын
Como, hacer no hablo ni entiendo. El ingles y me gustan los videos
@guillermovillafana1907 жыл бұрын
good afternoon I have a problem with the automatic washer whirlpool cabrio I get ERROR F50 I do not have the manual error codes washer
@alnavarrete7535 жыл бұрын
What is code LF?
@hot2handle5207 жыл бұрын
I did this test c1 filled the tub then shut off....
@lockyzeroone7 жыл бұрын
Joey P. Hi mine is doing similar and blink time and stop/pause after C1. is your washer fixed now? If yes what was the diagnostic?
@hot2handle5207 жыл бұрын
Lokesh Puri yeah my washer is fixed now we had to get a service tech out here not once but twice was something with the the bucket sensor I was stuck or something like that so it's more internal if yours is doing the same thing it's nothing a button or diagnostic test can fix you have to get a service guy out there to help take care of it and luckily was under warranty so didn't cost us nothing but if we had to pay out of pocket it was going to be at least the $800 bill
@lockyzeroone7 жыл бұрын
Joey P. Thanks for your reply. I appreciate your response. Mine is 5 years old, I would check with a technical and buy a new one if it requires more than $200- $300 to fix. Once again thanks for your reply
@melimel9617 жыл бұрын
These washers are junk, I'll never buy a whirlpool again! Samsung appliances last forever!
@MrCougar2147 жыл бұрын
Really? So all the recalls on their new lines of washers is what? cause they miss looking at them and want them back? Samsung's are damn fine looking, but performance is no better than any other make of appliances. What should really burn your ass is looking under any of these new washers. the outside looks pretty damn fancy and expensive until you look under the proverbial hood. Then you see exactly how cheap the parts are that go into them. I swear these people spend $25 bucks per unit to build them.
@DenSanAZ7 жыл бұрын
You do realize that the same company makes Whirlpool, Kitchenaid, Amana, Kenmore, on and on and on - right?
@Onelifeoutfitter6 жыл бұрын
I totally agree with you.. Junk! I feel like it only rinse my clothes