Check out our DIY Raptor Club store teespring.com/stores/diy-raptor-club

This video was exactly what I needed to troubleshoot and fix my dryer. Thanks!

Great video! Tip, if you are checking for continuity, check ALL possible related parts to this problem. I started with the thermal fuse and it was blown. I decided to keep checking and found that I was not having continuity in the heating element either. I took it out to inspect and found one of the rods had split (cut) which shorted it out. If I had not continued checking, I would have wasted more time and possible additional shipping cost if I had just ordered the thermal fuse only. Bottom line, since you're there, check everything! Good Luck!

Thermofuse was the issue in my Whirlpool Duet gas dryer. Great video. Saved hundreds of dollars. Great job sharing with us Michael! 👏🏻👏🏻👏🏻

This video was so good I never fix appliances but every step including showing the multimeter helped me fix my washer with one trip to ace hardware. Thank you!!!!!!!!

Wonderful information. You gave me the knowledge to discover and fix my issue. Had house painted and the exhaust shutters were sealed by the paint. A simple fix without a repair bill. WONDERFUL! Thank you!

I put in new coils, new thermal fuse and no change. Finally cleaned the heat sensor strips with some scotchbritepad. Even though they appeared quite clean and shiny, they must have been glazed over with something. After scrubbing them the clothes now come out dry. I say try the sensors first because its easy and cheap. Perhaps second if airflow out the duct is suspect.

This was so helpful!! Thank you so much. Turns out my dryer was fine but the thermostat was covered in lint.

Excellent video, you are great at explaining steps so clearly!

Worked exactly as explained thanks! Saved me an expensive trip from the repairman!

great video. Luv how you managed to get deep in to the machine to show the actual part. Thank you.

my dryer stop working, so i went and bought a used one, but i kept the old one, and watching a bunch of videos like this one, i fixed the dryer, in one month later, the used dryer that i bought, stop working, so i installed the one i fixed, it was so interesting, my wife will never be without a dryer again... first dryer was the thermofuse, and the second was the motor belt, order the part, and in half an hour i was done

@ 10:37 Isn't that the thermal fuse? All other videos I have seen show that shaped component as a fuse. The component to the right of it was likely the thermostat?

Very thorough and clear video.

Thanks for the tips, helped revive my dryer for a couple more years!

a thin magnet that extends is handy for dropped screws

Hi there! So first and foremost I have to tell you that yours is the best of MANY videos I've watched regarding my dryer. You're awesome! Now... my frustration (and forgive me because I'm about to be "that" girl) is that I can't get my back panel off! I've unscrewed everything you can and it comes loose on the top just fine, it's just stuck at the bottom. I think it's being impeded by a little black brackety thing down by the vent hose? Cannot, for the life of me, figure out how to get it to let go. HELP?!?!

Excellent.thank you. God bless for sharing this information with us

Bro youre a champion

Thank you for your good show.

This video convinced me that I can’t do this myself. Need a repairman.

Great help! Thanks!! 😊

My heating igniter won't even glow. Doesn't that preclude gas coils as being the issue?

Thanks Dude! That was super helpful.

Do NOT get those cheap screw in brush cleaning kits! Unless you actually want it to unscrew and be left inside your dryer duct hose. If so, go ahead. Get the push lock kit from Menards or Lowes.

best fuckin tutorial I have ever used!!!!!

Can you tell me the part number of the thermostat you replaced? Great job on the video, it was very informative!

My harbor freight meter starts at 1. When I test the thermostat (what you did at the end of the video) it jumps for a second and goes down to 001. Does that still mean it needs to be replaced? Thanks for your help!

Question. I am going to try to fix this myself. I think I can only do it to the coil part. My question is, what is the name of the screwdriver for the hexi size screws and what size. Thank you in advance

I cleaned my dryer vent and back of the dryer and my heat came back on but 24 hours later the heat went off again. Any idea what this could mean?

You had to take apart the whole thing to replace the most common failure point. Was this designed in germany?

Great job. Thanks

THIS DOESN'T APPLY TO ME I DON'T HAVE A GAS DRYER.

How do you know which problem it is?

Great video. I replaced the thermistor and new circuit board and still get a pf code after trying to start then turns off on a whirlpool duet dryer. Door switch and motor continuity checks out good. Any ideas where to check next. Thanks.

Mi se adora es eléctrica y parpadea el control panel;me podría ayudar a saber qué pasa!?

Thanks

Does replacing the coils allow the gas to turn on or just light the wick cus doesnt seem like gas is passing thru ???

I have that exact model and have been struggling to dry loads sometimes, when it isnt drying I hear a rattling noise that's going on and off, any idea what the issue might be?

Is there a fuse as well?

Does Lowe’s sale the thermostat or do you have to order it?

is there a heating element to troubleshoot ?

Excellent👍👍👍

Something odd about my two coils. You show your 3 wire connector on the front and the two wire connector on the back rod. On mine, it's reversed. My 3 wire is on the back rod and the two wire coil on the front. Never been opened up before. Wonder if it makes any difference? My 2 wire coil is bad. No continuity on that one. The other is fine. On a side note, I guess I should have watched the video first. I pulled the dryer away from the wall and started trying to take the back of it off :-[

Great video

I have a Whirlpool compact front load dryer model WED7500VW that I need to change the start capacitor and do not know how to get to it. Front panel screws are too close to the drum to unscrew and back panel supports the drum. Any ideas?

so my dryer it's marking on the screen wet, how can I fix? help me please

My dryer just stays on sensing any ideas

What’s this model number

Use a cordlesss drill.

Very intelligent

Hey where is that hotty...

My heating igniter won't even glow. Doesn't that preclude gas coils as being the issue?