You are a life saver. Couldn't figure out why the auger motor stopped all of a sudden and it's because I accidentally disconnected the flow switch hosing. Thanks! Saved me from spending over $100 on a new auger motor when I didn't need to.

Thank you so much! 30 seconds in and voila! Fikist!

great idea posting a video and thanks BUT... there are missing steps and video/audio cutoffs. If this is the way it was recorded then so be it... but if you have the entire video can you edit it to fill in the blanks/ Again.. thank you for posting this is I have to repair my auger/motor/bushing, etc.

1. Make sure you buy the correct auger speed and direction. No way to turn down the speed by much. 1 rpm clockwise rotation facing the shaft. There are other exact looking auger motors that turn at 2 rpm. There is a "trim" adjustment on some of the stoves, but no way are your reducing it 50%. Buy from a good company. I had my "second" motor only last 8 months. The original lasted 15 years. Never take apart the gear part. Tons of washers and gears will fall out. 2. My glass has and always gets dirty on my Whitfield. I bought mine in 1996, I have only replace the auger motor (twice). First one lasted 10 year (with one $.05 fix) That's all. Yes, I have outside air. 3. I have a UPS on my stove to protect it from zaps and power blips. Maybe that's why I have a 1996 original stove ? 4. Buy the best (.5 ash) pellets. Unless you only use it for looks, the better pellets create a lot less ash. I only clean mine every 3 weeks. I bought some cheap ones, never again. Every week was cleaning time. 5. The different Whitfield makes have different area in cleaning. The baffles are sometimes hidden. The parts seem mostly interchangeable.

How can I know which one is the power in the auger motor

I recently bought a SP22 Maverick pellet stove. For $40. Needed some repair. Bought a new augur motor. The problem I'm having is. Where to wire it up to the wire harness. The control switch and everything is fine. Just don't know where to connect the wires from the motor to the wire harness.

It seems like that bushing should be a bearing, to me. If it is loose and spins, can it be epoxied? My auger appears to be in the wrong direction, I don't know how that happened, if it is a problem or not. I see it move a little when the auger is activated, I suspect that must be related to my problem.

Auger stuck: Cheap pellets. Have heard of branch parts, too long pellets or plastic from the bags getting in by the company or user getting stuck in the auger. A worn bearing can also do it.

Thanks for the Video, I replaced the auger motor in my Whitfield with a new one from Whitfield last year. My problem is that now I cant slow it down enough even at the lowest setting. I was hoping to find a way to reduce rotation of the auger.

I was just given the exact stove for free. Any tips or things to look for? Also. I cant find the room blower. I found the combustion and exhaust fan. But cant locate the room air fan

Hey guys got a question. My whitfield pellet stove has a new auger motor and it worked fine until 2 hours ago... turn it back on the stove heats normal for about an hour then the auger just stops putting out pellets?

Good information, but I find myself hanging on your words but your editing be like, “ so you’ll need to install the scr...” “next you will need to check the bushing for any signs of we...” haha

if auger makes noise also can it cause feed issue and effect flame

My auger motor at the bottom with the fan is spinning back ward's how I fix that.

So where can I get a new plate nad Bushong for the advantage ADV model # 54753

Pretty good information

i have a quadra fire pelet stove and l have a problem my stove shut off time to time by her self,i keep it very cleen regulary,clean it every day every day the same like u showing in this video some time the blower stop and the stove shut down after i push the reset bottom and start working i fed up from this stove,l can not count on it,but l used all the time and now have a problem the store hier in saint jerome said u have to replace the blower and is not easy to fined it do u thing this the problem? or what? can u help me please$ and to get the parts too please thank u

everything works on our pellet stove except the auger. bought a new auger but it still wont run. can we run the auger manually with that test cord and put it on a timer maybe?

I've been trying to check out my auger but can't get the set screw off.. is there some kind of nifty tool with which to do that?

Any tips if your auger won't budge? I removed the motor thinking that was the cause, and it still can not be moved. I cleaned out every accessible space around it, still will not budge. It can not be turned by hand or with a tool, it can not be forced out of the stove(and believe me, i used quite a lot of force).

Why my ager motor still always on? Please help

If i ever have to replace my water pump ill call ya...or was that a termostat???

My whitfield pellet stove keeps feeding more than it can burn, what could be the problem !

Bushing is made out of bronze not brass.

Too many skip overs at important points

I'm not sure how to advise you. We don't often offer technical advice of this type directly but can get you answers from the factory technical department. Please direct all inquiries to our email address thru our web site info at WoodHeatStoves dit com

Good video, just too many cut off sentences and steps taken

Did you let your 8 year old edit this

This is by far the worst vid that I have seen. Just as you get to the bits that we need to see, the vid jumps on to another bit.

Are U drunk?