One way to protect the ways without losing a lot of travel.
Пікірлер: 62
@thehobbymachinistnz6 ай бұрын
That is a great idea to fix the problem Mark, well done.
@WinkysWorkshop6 ай бұрын
Thanks, clean up will be a lot easier now.
@larrythompson29674 ай бұрын
Some years ago, a shop I worked in had a machining centre with rubber way guards. It had a mechanism somewhat like a roll up window blind on one end that retracted the rubber sheet as the machine moved. I would add that the machine moved at some very high speeds as well. Keep up the vids, some pretty good stuff...................
@WinkysWorkshop4 ай бұрын
I thought about doing it like that also. Thanks
@TedRoza6 ай бұрын
G'day Mark. Great Way Modifications. I have recently purchased a Hafco HM-54GV Mill, which I am in the process of setting up. Mine has a lower consatine cover on the Y axis at the lower rear. What I have found is when milling, the chips etc fly all over the the Z ways & on the Horizontal spindle, so this Modification of yours could come in really handy. Thanks for your great videos. Ted
@WinkysWorkshop6 ай бұрын
Thanks, so far its worked very well.
@jrkorman6 ай бұрын
You had me wondering - "How's he going to keep the coolant off the floor?" - Well done and it looks good.
@WinkysWorkshop6 ай бұрын
I was using some aluminum sheeting for a while but it did not catch it all. Last time I used the mill with coolant I misplaced the aluminum and in minutes I had coolant all over the floor... The new way cover along with the new vise really did the trick.
@65cj556 ай бұрын
You're a clever man Winky.
@WinkysWorkshop6 ай бұрын
Thanks... I've been thinking about this ever since I restored the mill. I'm slowly clever... Ha
@terrycannon5706 ай бұрын
Mark I did something similar on my Bridgeport Clone. I used roofing rubber from Home Depot. I basically just replaced what the factory had on it but someone removed. Depending on how much milling you do before you clean the cover off the chips naturally will be laying on top of the vinyl and as you crank the Y in the chips will bunch up . Doesn't take long to build up a lot of chips when milling aluminum. Great idea you have with the nylon. My suggestion when milling plastics with dovetails is to use an end mill first to remove the bulk and then follow up with the dovetail end mill. Thanks for bringing us along.
@WinkysWorkshop6 ай бұрын
Probably right on the dovetail mill. I clean up my mill every time I use it. It might be the next day but it gets cleaned. :o)
@watcherwatchmen77856 ай бұрын
Another good source of free rubber sheeting is off an old treadmill. I have used them cut to size to line my toolboxes.
@WinkysWorkshop6 ай бұрын
Yes that would work great!
@halfstep676 ай бұрын
I bought some cheap yoga mats at wally world and they make great toolbox liners. They are less expensive and better quality than most toolbox liners and a little thicker to boot.
@m.c.mx16 ай бұрын
Another fine addition, good job.
@WinkysWorkshop6 ай бұрын
Thank you! Cheers!
@magicbytes38356 ай бұрын
Hello Winky, you could try a low edge baking tray between bottom of vice and table, just a suggestion. Good work as usual, thanks for sharing, we all love em. Cheers from me. 😃👍👍👍👍👍
@WinkysWorkshop6 ай бұрын
That would have worked well with the first vise, the second I just plugged the hole. I suspect the coolant that hits the guard now will be minimal now.
@magicbytes38356 ай бұрын
Yeah that is what I was referring too, but now you have another vice. Cheers 😀@@WinkysWorkshop
@petertitterton68366 ай бұрын
Good project, maybe consider having the smooth surface up, easier to brush the fine swarf off. Plus a mini version on the back of your new vice. I did that after seeing Curtis from Cutting Edge Engineering put one on his vice. My mill came with concertina bellows way covers they are a pain to keep clean!
@WinkysWorkshop6 ай бұрын
I was going to put the smooth side up but the material was hard to bend in that direction and much easier in the other. I'm not sure why... and it may have worked anyway but I was worried it would bunch up behind the table. The air hose seems to move the chips okay but you are right, smooth would be better.
@fullmetalpenguin6 ай бұрын
I have a roll of Harbor Freight tool drawer liner that’s been sitting on my bench for a many weeks waiting to be made into a way cover. Thanks for the reminder that I need to stop procrastinating.
@WinkysWorkshop6 ай бұрын
That is awesome! I looked at lowes and all they had was a foam material
@cyclebuster6 ай бұрын
When i saw the opening scenes i thought you might hook the rubber to the poly. And have it pull the rubber down across a steel roller against the column. My vice is an 8 in Palmgren on a rotary base. Its also made for coolant, but it has the back 1/2 in or so cut off because its far too long. I moved it to the far right of my table, and to the front slot, gaining a lot of travel back. And my 8 in rotary table is on the far left, on the center slot, and there is room for both. If your mill holds up to that much material removal and dont cook the spindle, i will be doing mine this summer, at least 1hp. I love everything about mine except the loose x nut, and the power. They are nuts on the price of a new one, and its a real complex item to reproduce, let alone find a leadscrew. i may have to make one, but if I do it will become a 16 thread instead of 8. Great job!
@WinkysWorkshop6 ай бұрын
16 TPI is slow for a mill table. My wells index is 5 TPI. I like 10 TPI the best. I have no idea why they went with 5 TPI.
@cyclebuster6 ай бұрын
@@WinkysWorkshop slow machines live longer. i forgot mine is 5tpi. Maybe i will go to 10
@WinkysWorkshop6 ай бұрын
@@cyclebuster my RF 30 drill mill was 10 TPI. The first few times I milled with the wells index I shattered a few carbide mills.
@BenMitro6 ай бұрын
I thought of using a narrow roller blind (from a window) - these are cheap from our "Bunnings" stores here in Australia and easily replaceable. You can get them in 60cm, 2' widths too.
@WinkysWorkshop6 ай бұрын
I thought the same but I was a bit concerned with the strength.
@sky1736 ай бұрын
Looks like a good idea. I might have to try something like this on my little Atlas mill. Thanks for sharing.
@WinkysWorkshop6 ай бұрын
Go for it! Thanks
@alanjackson43976 ай бұрын
Another nice design. Love your creativity.
@WinkysWorkshop6 ай бұрын
Thank you so much 😊
@MyMiniHomeWorkshop6 ай бұрын
Necessity, the mother of invention 👍
@WinkysWorkshop6 ай бұрын
Yep and the ways needed to be covered. Thanks
@MyMiniHomeWorkshop6 ай бұрын
@@WinkysWorkshop I have a similar problem on my little homemade lathe and there's a small thin mouse pad sitting on my bench that I intend to do something similar with, I must get around to doing it. 👍
@TangentJim6 ай бұрын
Winky - I like your way protector . I like the spring design . Excellent Video. -- Jim
@WinkysWorkshop6 ай бұрын
Thank you!
@angelramos-20056 ай бұрын
Good idea,Mark and good CNC vice.Thank you.
@WinkysWorkshop6 ай бұрын
Glad you liked it! thanks
@TheAyrCaveShop6 ай бұрын
Nice out of the box thinking, looks like a winner !
@WinkysWorkshop6 ай бұрын
Thanks Dean, it seems to work well so far.
@GOTICDRAW6 ай бұрын
Hola, tengo tengo la Index 55, gracias por tus videos, me han servido de mucha ayuda
@WinkysWorkshop6 ай бұрын
Glad I could help
@robert5746 ай бұрын
I have some large sheets of (2 blue, 2 black) 1" thk plastic (3ft x 5ft) that were given to me. The surface is flat and smooth, and they are new and were left over from installing bathroom dividers. At the time, I thought it might make a good table top on a bench to put under the lathe. They said they cut it with circular saws, but I picture those chips will be everywhere. Too bad you're not closer, I think you would make something out of it.
@WinkysWorkshop6 ай бұрын
Yeah that's probably some useful stuff. You need to hang on to it.
@alfredrichter62366 ай бұрын
If you want to know how the oil resistance of your rubber mat, just take a pice of the offcut and put it in a bowl of oil. After a week, if it is still the same it is oil resistant.
@WinkysWorkshop6 ай бұрын
Good idea, although at this point I'll just wait and see.
@wallaceknifeworkshomestead6 ай бұрын
Great fix!! Speaking of vices, That blue vice on that green machine looks horrible!! C'mon man,, 🤣🤣🤣
@WinkysWorkshop6 ай бұрын
Haha.... yeah, I do need to paint it for sure.
@leslieaustin1516 ай бұрын
Nice job! But get that hole plugged a.s.a.p.. thanks Mark. Les in UK 🇬🇧
@WinkysWorkshop6 ай бұрын
Done... I installed a set screw with pipe thread sealer. Thanks
@thercbarn50016 ай бұрын
Nice project.
@WinkysWorkshop6 ай бұрын
Thanks!
@joell4396 ай бұрын
👍👍😎👍👍
@WinkysWorkshop6 ай бұрын
Thanks
@TomasFaalPetersson6 ай бұрын
Looks great, but could you explain why its needed?
@WinkysWorkshop6 ай бұрын
Good idea, the Y axis (away and toward the operator movement) rides on ways (a cast iron smooth bearing surface). Without this cover the metal chips and coolant get on the ways. The chips sometimes get stuck between the two sliding surfaces and damage them and the coolant will make the ways rust. The coolant has rust inhibitors but over a long period of time it will cause damage.
@jubiletabustamanteserrano24466 ай бұрын
As always, good work, although not the most precise. I still like it.
@WinkysWorkshop6 ай бұрын
Thanks. Sometime precision is not needed. In the case of the plastic slide it needed to fit loose. In fact the angle of the dove tail was even wrong. I assumed most machines used the same angle but it makes sense that the knee would ne more extreme based on the weight and angle of the load.