“Should be simple enough I can handle it.” I said that about my first wife. 🤣😂😜🤪

great info. want to tackle the same swap soon in my new project truck

This vid clearly explained everything i needed for my 4l60 to 4l80 swap as far as wiring goes i did need to shorten my rear driveshaft slightly because of trans housing being a bit longer 4x4 drivshaft needed lengthening as well crossmember repositioned back couple inches as well

Thanks for making this video. I trust this channel over almost anyone else that would make this. Love your channel man. Learning a lot from you.

Great how to video probably saved us common folk a bunch lunch monies

At the hospital. Treatment will have to wait, Goldie Hawn is up.

I can't thank you enough for this. Used to use lt1 all the time when I was only dreaming about projects. I am gaining hope with my real life swap project/necessities in order to keep on truckin. Keep up the good work.

My best Rick Flair impression- "WOOOOOHH!!!"

Now i can get my 80 e swap later on and I’ll come back to this video.thank yo soo much made it seem so easy and not complicated.jeep up the good vids 😎

holy cow at 5:58 you could have told that poor shrink wrap. say hello to my little friend..lmao.. having more flashbacks and you nailed it on info

Really appreciate the video. Just acquired a ‘03 Chevrolet Tahoe swapping a 6.0/4L80E into it and this came in handy.

love the mix second vid in a row Great music keep it up were on a streak

I AM doing the 4l60e to 4l80e swap in my 1995 c1500. I have the computer out of a c2500 with the same applications such as 5.7. And 4l80e. Where as mine was a 5.7. And 4l60e. My question is. If I put the computer and transmission from the 2500 in my c1500. Do I need to change anything on the wiring harness? And if so. What? Any help very appreciated.

When you re-pin the PCM with the speed sensor did you just load 4L80E files on the PCM and it automatically picks up the added speed sensor or do you need to program and tell it too

I was lookin into how to swap an 80e literally just yesterday. Concidence? I think not.

All the years my dad was a transmission mechanic, he retired when everything started going electronic!

Made it look easy. Crazy how simple that was

You did it! Congrats! Now do the segment swap, remove ALL trans torque management, and set shift times to 0. I can email my hptuners tune if you want for when I did my 4l80 swap. Shoot me an email.

Awesome channel man! Just stumbled onto it. I am swapping out my 60e behind my 6.0 for an 80e this summer. This will help a lot.

Can you help me out . I got a 6.0 lq4 n I got a 4l80 e would you be able to help me find out what flex Plate I would need thank

Brown wire in "U"= "brown wire in you" in his head 😆🤣 love it

Oh, and by the way unlike here where you're doing a 4L60E to a 4l80E this is a 4L80E to a 4L80E swap so a 91 4l80E being swapped out for a 92 4L80E like I said all my research told me they should be the same transmission but just apparently the pinouts different. All the info I could find before the transmission got here told me 91 through 93 had the same pinout. But then I looked up 91 pinout again and it actually did show this green connector. Versus the new 92 one which has a square peg in the center for the connector to hold on instead of the two rectangular holes to hold the connector on.

I want to see the 1st gear between the trans. I hope you got video to compare. Thanks for the info on the swap man

Wow, that was surprisingly simple for a trans swap. Glad to see Goldie is getting back on her feet!

So glad you made this video. Swaped them trannys and had no over drive.

This Brown wire in U.. Heh. 3:32

Best video out there on the wiring 💪🏼🔥

And that folks "is how it's done".

Hello! I’m having trouble with my swap cause the only thing I find is for a 99 and newer models. I have a 1997 and I have completely installed 3/4t running gear in. Do you have info on a 97? The wire PIN numbers are different for computer. I have finished the transmission end and I have 4l80 computer

I need to know how to put back on my wire harness?? And I'm swapping a 4.8 4l60 to a 6.0 4l80 why do I have to tune my computer if it's the original computer the the stock 6.0 and transmission

Another great video do these conversions at least one a week you did it perfect bro

Question what happen if you don't swap the wires

How hard would it be to swap out my nv3500 out of my 04 2500HD 4x4 to a 4l80e not a fan of the manual just want to hop in and go

Would this work for swapping out a 94 Chevy Silverado k1500 4L60E for a 99 4L80E into the 94 Chevy K1500 Silverado Z71 truck

I'm honestly watching these videos closely because I want to swap my 03 Envoy to an 80 as well, and I hope it will be the same deal. Also uses the same computer as the trucks. I hate that 60. Really want to take care off this before I go turbo

Have you ever had a 4l80 shift fine and then throw a code and start skipping 2nd and going in and out of 4th no lock up?

It is F’ed up that I have more snow here in NC than you do .

Love how often your videos come out nice job

How would the wiring be different in a 96 tahoe?

Bro I have a question maybe you have the answer. I have a 92 Chevy 3500 with a 454 in it and the early 4l80e transmission. I had to splice in a new wiring harness bc the customer was having to drive around with the front drive shaft out bc the drive shaft was rubbing the plug. So we had to update the internal harness and external harness. Got it all rebuilt and wiring done and I keep getting code 73 for a force motor. Tried 3 different pcs's/ force motors. I ran electrical checks and it's getting the correct amperage I believe. Now I also replaced the throttle position sensor bc it wasnt building up to 5 volts as it should. The new throttle position sensor is still not reaching 5 volts. Still the same code. It clears and reappears instantly. I'm thinking it could be the computer but I don't want to just throw parts at it we have alot invested in it as it is. If you have any clue what it could be I would really appreciate your opinion. This truck is plaguing us and we're kind of in a tight spot and need to get it done. Thanks

Thanks for the tutorial, just finished the job thanks to you

Hi, the 4l80e I got it has 2 speed sensor, now the one on top of the shift switch the plug seems different then the one on the rear of the trany. What will I have to do there? I got the new added plug connected to the pcm already but the other plug doesn't fit that one sensor.

Have a question when done with the wire transfers on transmission side do I hook up the new vss to the input vss on transmission or the output vss ???

Swapping out one of these in an RV. My connector which is a 91 is the same one here shown on the vehicle you're working on the green with the two slots and I've have a 92 4L80E that I was planning to put it in the old ones place will this type of swap work with that?

SniderTron 3000 will that work for the 1994 era i have the right computer just the wiring harness for a 4l60e only wiring harness i could put my hands on

I have a 2006 4l80e trying put in my 2001 2 wheel but the Neutral safety switch is different from the 2006 it’s one big plug versus two little plugs need some help

You ever wired a 80e to a 12v ?

Do I still need to tune it if I do this?

Same process even in a trailblazer ss I’m trying to go 4l80e?

Hey brother what is the size of that piece of angle iron did you used on that crossmember

Liked the video I'm currently doing a 4l80e swap to my impala ss also did a ls swap to it what you showed in your video will it work on my impala??

difference in 4x4?

Did you have to flash the ecm to let it know its a 4l80e

Have 1994 Chevy truck would like to do 4l80e swap can this happen with little expenses other than transmission?

Kind of shooting in the dart for a response, but will this work the same with a transfer case?

When you buy the plugs do they come with a full wire to pin in the pcm

What does this wiring do

Do you need to tune the ecm?

Is the wiring the same on the NBS and NNBS trucks?

Where you located I need help with mine !!

What car did you put the 4l80e

What do you do with the Red/Blk wire from pin 22 on the C2 connector?

Will this work for a 08 silverado nnbs had a 4l60 got a 4l80

what about 1995 4l60e to 4l80e swap w/ the cpu under dash ( red & blue 32pin on ea. side ) I'm stuck ...haalllllPPP !

Thise connectors never hold like they're supposed to,I always use a little silicone to ensure they're solid

I need fine website for my 93 chevy to do this cant fine website

My 92 4×4 454 BBC convert to carburetor OK I kneed America chavy guys direct me 4L80 transmission wire up and shift

I heard that if it fits in the pocket it was free at JYs lol that’s how it was back in the day at least lol I hate vehicle wiring. Bunch of spaghetti 🍝

¡Good and helpful job! I have an ls1 with the 4l60 that came on it but i want to swap to an 4l80, ¿can i do the same wiring of this video to make it work? Thanks.

(9:33) I also get hair stuck in my beard all the time, weird how it ain't even mine half the time. Rad vid dude,I've re-pinned harnesses before. Fackin hate it cause its so easy to repeatedly fuck ur self n break the wire at the crimp when re assembling. Ya made it look easy👍

I have a 1992 Chevy Silverado k1500 4x4 it has the 4l60e in it and I want to put a 4l80e in it what all do I need to do

Did you have to retune the pcm for this or no

Im literally under my truck right now doing the wiring from ur video , just worried about deleting to wires for the vss , what are they for? Im goinv ahead and doing it your way anyways just curious

Where did you connect that speed sensor plug you added to?

I have an Fbody that was a LS1 T56 car. T56 was removed after the LQ9 went in, now the turbo 350 is toasted. Should buy a more expensive turbo 350 and still not have an overdrive or do this. Have 500hp or something like that.

if u do 80 swap do u have to modify the transmission lines?

Damm I just bought the Hooker 4L80 cross member

Will this same procedure work for swapping a 01 4l80e 4x4 into a 97 k1500 z71?

You should have mentioned the segment swap in ECU.

What model truck and transmission

Love the beats

They have this beautiful wiring pin removal tool that is soooooo worth it. Under $10 on amazon for 26 piece kit. Insert tool over pin, pull wire from behind, haha thats what she said!!!😭😭😭🤣🤣🤣 and bam done!

Hey, I looked through the comments. Is this the same procedure for a 4l60e to 4l70e swap in a 2007 saab 97x?

What year harness does this work for looking to swap out my 4l60 to 4l80e on my 2002 Silverado what year does the 4l80e have to be

What dip stick u use

So on a 2wd, what about the driveshaft? I have a 2001 1500 4l60 and am going to build my LM7 and want to upgrade to the 80.

Great video good to know

How hard would this swap be to do on jack stands rather than on a lift

Do you have to reprogram the ecu?

On mine "sloppy mechanic style" only swapped the brown wire over to the white wire and left wire wire out completely

Got damn just when I was thinking I needed more to watch

Wats the size of the driveshaft your using

This brown wire in U! Hehe 🤣

Thanks

Most junkyard probably only be a dollar or two for sure love junk yard hunt lol

Do you have to tune it or can it run after that.

doing this tonight. thanks for the video so i don't have to read. :)

So am i gunna need to get my computer flashed ???

Fudge! I wish I understood Canadian!

Can i use a 92 suburban 4l80e for an ls Swap. As far the wires for the ecm