5 Expert Table Saw Tips

Рет қаралды 547,933

Күн бұрын

0:00 Introduction
0:25 Lining up the cut mark
1:44 Squaring the miter gauge
3:55 Keeping wood from pinching the blade
5:22 Cutting plastic
6:47 Setting the blade angle
9:36 Setting the miter gauge angle
Master craftsman and woodworking author Nick Engler reveals five professional secrets to help you get better results when using your table saw. For more table saw information of the printed variety, pick up a copy of Nick's book, "Using the Table Saw" from our store at workshopcompanionstore.com/pr... .
To see all of our videos and SUBSCRIBE for more, see: / @workshopcompanion
Also visit the WORKSHOP COMPANION GENERAL STORE where we offer a wide selection of Nick's BOOKS and PROJECT PLANS in digital format: workshopcompanionstore.com/
Pick up one of Nick’s books FREE just for visiting!
To follow us on social media, try:
FACEBOOK - / workshopcompanion
INSTAGRAM - / workshop_companion
For our non-English-speaking viewers: Closed captions can be set to any language. Click on “CC” (Closed Captions) at the bottom of the screen to turn them on. Click on the gear (Settings) and a menu appears. Click on “Subtitles/CC” and another menu will appear. Click on “Auto Translate” and a menu of languages will appear. Click on the language you want for the closed captions and you will be returned to the video -- closed captions will appear in the language you have chosen. If these captions cover up some of the action, place the cursor over the captions, press and hold the left mouse button, then drag the captions to where you want them on your screen. Release the mouse buttons and they’ll stay there.
Para nuestros espectadores que no hablan inglés: los subtítulos se pueden configurar en cualquier idioma. Haga clic en "CC" (Subtítulos) en la parte inferior de la pantalla para activarlos. Haga clic en el engranaje (Configuración) y aparecerá un menú. Haga clic en "Subtítulos/CC" y aparecerá otro menú. Haga clic en "Traducir automáticamente" y aparecerá un menú de idiomas. Haga clic en el idioma que desea para los subtítulos y volverá al video; los subtítulos aparecerán en el idioma que haya elegido. Si estos subtítulos cubren parte de la acción, coloque el cursor sobre los subtítulos, presione y mantenga presionado el botón izquierdo del mouse, luego arrastre los subtítulos a donde quiera que estén en su pantalla. Suelte los botones del mouse y permanecerán allí.
Our Music is Licensed through Epidemic Sounds - www.epidemicsound.com/referra...
And thank you so much for your time and interest!

Пікірлер: 270

@xsbxsbxsb 2 жыл бұрын

Best time to discover Nick Engler - 10 years ago! 2nd best - right now! Thanks for sharing your knowledge!

@WorkshopCompanion 2 жыл бұрын

Most welcome...I think..

@billhandymanbill2775 4 ай бұрын

Thanks for the video tips. I have installed a magnetic relay "STOP" switch a my leg level on the table saw frame and by tapping the switch to turn off the table saw without having to take my hand and eyes off the wood and find the the table saw off switch. I don't use plastic push stick because they can shatter if they tough the blade and I don't use the "bird's mouth" push stick anymore because the pivot at the back of the wood and the front of the wood is free to rise up because of the rotating blade. Instead, I use a longer wooden push block that provide downward pressure and forward motion all in one movement to prevent kickback and improve table saw safety.

@drochon6672 2 жыл бұрын

Great tips. I never thought of using my angle finder to set up my mitre fence.

@meatmaster8636 2 жыл бұрын

me either

@louislandi938 2 жыл бұрын

Excellent and impressive tips. Wish I knew them years ago. Many thanks!

@joemule8858 2 жыл бұрын

FANTASTIC TIPS FOR NEW TABLE SAW USER, THANK YOU!!!

@drsbrettsavage 2 жыл бұрын

Your generosity and knowledge is utterly welcome and amazing. Thank you

@farrierss1724 2 жыл бұрын

5 tips and somehow you went 6 for 6. Nice! One of the best "tips" video I have seen. I was a little worried that you were going to put the wedge in with the saw still running. Well done.

@sjfarrell2.03 2 жыл бұрын

Ill be using tip #5 tomorrow. Thanks 👍

@ellisreeves8936 3 жыл бұрын

Great tip Nick, so simple but some if them I have never of. Keep them coming

@WorkshopCompanion 3 жыл бұрын

Will do. And thanks.

@JohnM1774 2 жыл бұрын

Fantastic tips !!!!!! Thanks a million 🙂

@keithkolbo2735 2 жыл бұрын

By far the best table saw tips I have seen. Thank you!

@WorkshopCompanion 2 жыл бұрын

Most welcome.

@michaelclark1605 2 жыл бұрын

Awesome, thanks for these!

@paytonjohnson660 2 жыл бұрын

Some great tips. Thank you

@whomadethatsaltysoup 2 жыл бұрын

Thanks for sharing! Love the tip with the digital angle finder.

@WorkshopCompanion 2 жыл бұрын

Thanks.

@glencrandall7051 2 жыл бұрын

Some of these I knew but have forgotten. Did not know about cutting plastic. Thank you for sharing. Have a great day and stay safe.

@WorkshopCompanion 2 жыл бұрын

Same to you.

@tomjeffries58 2 жыл бұрын

Great tips!

@larryjacobs5713 2 жыл бұрын

Love your knowledge and explanation. Thank you so much

@WorkshopCompanion 2 жыл бұрын

Most welcome.

@Habibulla.M 2 жыл бұрын

Nice and useful tips 👏

@robertnolan667 2 жыл бұрын

great tips thank you

@almosh3271 2 жыл бұрын

Very nice tips, thanks for sharing

@WorkshopCompanion 2 жыл бұрын

Thanks.

@brucewelty7684 3 ай бұрын

hmmm I tholught I had all your vids watched and liked.

@m.a.r.services5720 Жыл бұрын

Thanks! Great tips

@bryenlink Жыл бұрын

This intro made my day. Fantastic.

@WorkshopCompanion Жыл бұрын

Thanks for saying.

@mangakamotlomelo1532 2 ай бұрын

You guys you are helping me more than I can possibly begin to explain for sharing may God bless you guys

@WorkshopCompanion 2 ай бұрын

Thanks.

@utoobia6872 4 ай бұрын

I just realized that I have now watched several of your videos since discovering your channel without subscribing, and felt like I was stealing. You sir are awesome, and I am just a new subscriber along for the ride.

@WorkshopCompanion 4 ай бұрын

Thanks...and welcome.

@atgiovina Жыл бұрын

Nice tips!

@garryblack764 Жыл бұрын

Great video! Thank you

@WorkshopCompanion Жыл бұрын

Most welcome.

@marcothehammer Жыл бұрын

Great tips. My favorite is setting the miter gauge. I did not see that one coming!

@WorkshopCompanion Жыл бұрын

Thanks.

@marty3553 2 жыл бұрын

Very helpful thanks 🙏

@ldhoggaro5425 3 жыл бұрын

Great tips! Wish you would do a set for the Shopsmith table saw.

@grzesiekk1599 2 жыл бұрын

Thank you!

@pipilim6491 Жыл бұрын

Great teacher. Thanks for sharing.

@WorkshopCompanion Жыл бұрын

Most welcome.

@willem878 Жыл бұрын

I must say that you gave a lot of tips in the years that I follw you. Please keep on doing. Even someone as me cannlearn from it. Making stuff dead accurate with my saw and most of it with red cedar. A 0.5 mm is my maximum deviation ;-)

@divinenonbinary 4 ай бұрын

Most useful KZfaq channel!!

@BoogieBear Жыл бұрын

Genius stuff, thank you

@newlibertarian139 2 жыл бұрын

For all the tips you discuss, there are just as many other tips by carefully watching. Thanks for the great content.

@WorkshopCompanion 2 жыл бұрын

You get it. You're most welcome.

@sanjaydate Жыл бұрын

excellent tips and you explained it very well. Thank you sir. !!!

@WorkshopCompanion Жыл бұрын

Most welcome.

@theclosetcarpenter7172 2 жыл бұрын

These are really good tips. Especially the plastic cut. I use acrylic under everything I glue so I just have to clean the glue off when I'm done

@WorkshopCompanion 2 жыл бұрын

Good tip. Here, we use wax, waxed paper, and sheet plastic, depending.

@tyronedeasbrailsford951 Жыл бұрын

Very informative! Thanks

@WorkshopCompanion Жыл бұрын

Most welcome.

@Sidorvm 7 ай бұрын

This is great set of tips!

@WorkshopCompanion 7 ай бұрын

Thanks for saying.

@franciscodsouza4757 2 жыл бұрын

Thanks. Learnt a lots on your video.

@WorkshopCompanion 2 жыл бұрын

Most welcome.

@newlab20 Жыл бұрын

I really appreciate you videos!!

@WorkshopCompanion Жыл бұрын

Thank you. We appreciate your kind words.

@prsearls 2 жыл бұрын

Good tips. I have considered getting an inclinometer and after seeing this, I'll definitely get one. This will work well on setting the planer fence ninety degrees to the bed.

@WorkshopCompanion 2 жыл бұрын

It's one of those tools that, once you have it, you find a zillion uses for it. A month after purchase, you wonder how you ever did without it.

@MDay8 2 жыл бұрын

I just bought that digital one, and I completely forgot the zero-function, so thanks for reminding me that the ground on which you work on is never 0 degrees, haha

@WorkshopCompanion 2 жыл бұрын

@@MDay8 So True. The hangar in which we have our shop is 100 years old, and our floor has been afflicted by tectonic drift over the century. Not only is no tool sitting level, no tool is at the same angle!

@Oh6Torch Жыл бұрын

I just discovered your channel. You sir, have earned a subscriber.

@WorkshopCompanion Жыл бұрын

Thanks...and welcome!

@MilmoWood 5 ай бұрын

Brilliant

@Martin-yl5zb 2 жыл бұрын

I watched quite a few tips videos before this one. You showed some new tricks that are very practical. Thank you!!

@brianstevens3858 2 жыл бұрын

As usual all nice stuff, I do wonder how many peeps don't know the run grooves for the sled are parallel with the blade and thus make a good source of squaring....

@kathrynnewton8721 Жыл бұрын

So informative, wished I’d known this before. I’m selling my Bosch table saw as I’m going to England. But hope I can buy another one when I’m settled. Thank you!

@WorkshopCompanion Жыл бұрын

Most welcome.

@intrepidus3378 2 жыл бұрын

point 2 - you said checking the miter gauge against the fence for square will tell you if the gauge is square to the blade, assuming the fence is parallel to the blade. That is true. But it's really not what you should be looking for. You can make a square cut using a miter gauge even if the gauge is not square to the blade. The key is that the fence for the miter gauge must be square to the miter slot/miter bar. Love the tip about using the inclinometer to set the bevel angles. I have one. I don't know why I don't use it more.

@ronh9384 Жыл бұрын

Great tips! Nice work Nick and Travis. If I had another thumb you would get 2 thumbs up! Something I found out while making a segmented turning was to zero the angle box (in the 8:55 minute mark) on the cast iron table instead of the throat plate. Also some angle boxes are very sensitive and if the aren’t 90 degrees (front to back) to the cast iron table when measuring it can slightly throw the angle off. It may have been my particular angle box. Was just my particular issue but when I started doing those two things it corrected my issue.

@WorkshopCompanion Жыл бұрын

You might want to watch or video on aligning and adjusting a table saw. In it, I suggest to the viewers that they spend some time carefully adjusting the throat plate so that its dead-on flush with the table. There are dozens of small measuring devices -- squares, triangles, height gauges, and so on that need to be set next to the saw blade. In order for them to be accurate, the throat plate has to be properly aligned. A digital angle finder is one of the very few that can be registered several inches away from the blade, then used to measured the blade position. I registered the angle finder off the throat plate because I know I can trust my throat plate -- with ALL of my measuring devices.

@dgale1023 3 ай бұрын

thanks for the tip on opening the kerf. I was watching for the only solution for what I am doing as I use a 7-1/4" blade 1/8" there is no splitter for that. Don't anybody jump in and say thin kerf microjig won't work. Thanks for your knowledge. Now I need to subscribe To get more info. Thank you

@WorkshopCompanion 3 ай бұрын

Most welcome.

@meangreen7389 2 жыл бұрын

Thank you from a new subscriber.

@WorkshopCompanion 2 жыл бұрын

You're welcome...and welcome!

@valeriehenschel1590 Жыл бұрын

Thank you.

@WorkshopCompanion Жыл бұрын

Most welcome.

@fayz44awad 2 жыл бұрын

Thanks 👌

@fireworxz 2 жыл бұрын

Thanks

@dand3975 2 жыл бұрын

I cut lexan last week with a carbide rip blade, worked just fine. I cut same lexan in power miter saw, very bad idea resulted in bad kickback. I have had good results cutting 1/8" aluminum on tablesaw with fine tooth paneling blade on tablesaw. Great tips on the use of the inclomometer (digital angle finder) thank you for all the tablesaw tips in this video.

@WorkshopCompanion 2 жыл бұрын

Most welcome.

@brianstevens3858 2 жыл бұрын

Yea a paneling blade will also cut most roof steel in a circular saw, but makes hella racket and leaves sharp edges that must be dealt with, so gloves and ear protection a must.

@huejanus5505 2 жыл бұрын

When cutting strips of laminate, i spray some contact cement on a piece of mdf, only, stick the laminate to it and make the cuts. You can cut extremely thin strips with no chipping and it’s easily removable afterwards.

@WorkshopCompanion 2 жыл бұрын

Good tip.

@steves7896 2 жыл бұрын

I hate stopping my saw in the middle of a cut. And I don't like stopping the wood either if I can avoid it. Unless I make a complete, continuous full cut, there's always some little ridge or burn mark on one side of the kerf or the other. As always, great content.

@brianstevens3858 2 жыл бұрын

the trick is after saw winds down, move it back about an 1/8th inch or so so teeth are free in the kerf, then don't re-engage until blade reaches full speed.

@Beefbananas 2 жыл бұрын

Good tips! How come you don't use a riving knife or splitter?

@WorkshopCompanion 2 жыл бұрын

Thanks. It is an old, old saw and there are no riving knives available for it, and the mangled splitter that came with it interferes with the overhead guard we installed. (No, the Delta Disappearing Splitter won't work; we've tried.) I have gotten used to turning off the saw when the blade binds and inserting a small wedge in the kerf.

@rodneywheeler2278 5 ай бұрын

Nice tips. Please use your upper saw guard to encourage everyone to do so.

@barrywaitkus3739 Жыл бұрын

You are do good.

@Shadow74342 Жыл бұрын

Brilliant...the wedge thing cures a common problem....anyone know how to fix a Makita fence that doesnt seat in a straight line?

@lemhanback9595 2 жыл бұрын

Were you ever a woodshop teacher? Because you should have been. Your personality makes even the things that may be mundane and makes them fun to learn. Thank you sir.

@WorkshopCompanion 2 жыл бұрын

You are most welcome. I taught craftsmanship and wood engineering for many years at the University of Cincinnati.

@lemhanback9595 2 жыл бұрын

@@WorkshopCompanion sure wish I could have learned from you then, but that's ok I'm learning now. Just hoping 52 is not too late. 😂😂😂

@WorkshopCompanion 2 жыл бұрын

@@lemhanback9595 Have two decades on you and I can say with certainty, it's not.

@bfflorida2311 2 жыл бұрын

Great video and tips as always 👌 👍👍👍 Just some observations tips... 4.o = safety tip... When used as shown, the blade is pushing the cut part forward (outfeed), so make sure you are expecting that or part will fly 😀. Normally, resistance is in the direction of the operator. ALSO, very important DO NOT use carbide tip blades to cut backward !! 5.o = if you place an inclinometer as high as you can (vertically from the table top), even more accurate reading is possible. Thank you for sharing your wealth of knowledge with us.

@HepauDK 2 жыл бұрын

It doesnt matter how high you place the inclinometer. If the bar or blade is perfectly straight, the angle and precision will be the same. If they are not, you will not be able to trust ANY measurement. The only time extra length will matter, is if you use the 3-4-5 (Pythagoras) method to square something.

@lcmmassa8571 Жыл бұрын

Thanks. I may try using my table saw again. Can I also cut plexiglass as you demoed the plastic cutting? Does thickness or bulletproof plesiglass change the matter and how?

@mattedwards4533 Жыл бұрын

Another well done video! I was thinking that on your first part on cutting a board to a specific length why not use the kerf on your miter guage board to measure?

@WorkshopCompanion Жыл бұрын

It works for a short while, but normal saw runout soon widens the kerf and the accuracy evaporates.

@vjurco 2 жыл бұрын

Good tips, thanks. Just a note... +/- 0,1 deg precision may easily result to 66,4 or 66,6 and you never know. Inclinometr is very useful but in such a case, when you need critical precision, I would rather use calibrated ruler or something like that.

@sethnoble610 2 жыл бұрын

I know this an older video, but I hope you have replaced the bearings on that tablesaw by now. They're screaming for some love ole' son!! Love the videos

@user-yt4xu4en5f 7 ай бұрын

The dialogue on this video is hard panned to the left channel. Not sure if anyone has mentioned it. 👍🏻 love your stuff!!

@WorkshopCompanion 7 ай бұрын

We're aware; rendering mistake made early on, plan to redo the video sometime in the future. Thanks for the kids words.

@connecticutaggie 2 жыл бұрын

Great tips. Note: As an alternative to Tip 1, I often lift the pack of the piece up, keeping the edge flush to the fence and more the piece forward such the the marked edge is lowered to contact the blade. I then line up the mark with the blade then carefully lower the piece back down making sure it does not move side-to-side. It was probably not as accurate as using a straight edge but better than eyeing it.

@reyreyna1068 2 жыл бұрын

Great video Sir 👍 what kind of blade did u used?

@WorkshopCompanion 2 жыл бұрын

FS Tool

@thedevilinthecircuit1414 8 ай бұрын

When using the digital angle gauge ("inclinometer"), it is critical to rest it on the table and then rock it up onto the blade. The reason is any slight tilt of the device forward or back will result in an imperfect reading.

@mblatner 6 ай бұрын

Sounds like the saw is getting ready for some new bearings

@WorkshopCompanion 6 ай бұрын

Yeah, we were thinking about replacing the bearings but decided to find a slightly newer version of the same model. The slightly newer version has adjustments that allow you to further adjust the angle of the blade. - Travis

@bradzurcher2775 Жыл бұрын

Fascinating stuff. Thank you for sharing with us.

@WorkshopCompanion Жыл бұрын

Most welcome.

@connecticutaggie 2 жыл бұрын

#2 assumes is that the faces or the piece are parallel. One way to check that is to flip the other piece at the cut line and stack it on top of the first piece. This puts the same face against the fence. Now run your finger on the cut end and make sure the piece line up perfectly. Now flip the pieces together so the other side is against the fence and check again. If one matches but the other doesn't the faces are not parallel. If they are both off then likely the cut was not square.

@CowsGoM3ow 5 ай бұрын

I thought you were only to use jointed boards on a table saw unless it's clamped in a jig? Ofc you don't have to, but it's not as safe. Edit: Jointed, then can be squared on a table saw/planer

@connecticutaggie 5 ай бұрын

@@CowsGoM3ow Jointed boards do not necessarily make a board safe or unsafe for use on a table saw. Contractors rip lumber store wood all the time and almost nothing that comes out of lumber store is square or parallel. You just have to use the right technique for the board you rea cutting.

@CowsGoM3ow 5 ай бұрын

@@connecticutaggie Ofc you can use unjointed boards, but jointed boards(2 sides) are safer. If you think that's wrong, then go rip a log on a table saw without a jig. Or a extremely cupped/twisted board. And if you are checking for accuracy anyways like you were nitpicking orginally, you would want a square or 2S jointed board.

@chrisyu98 2 жыл бұрын

Great tips, can you show the start/stop control for the table saw. That looks like a much more useful location rather than under the saw.

@WorkshopCompanion 2 жыл бұрын

I think so. Safer, too. It came with an overhead guard that we installed on the saw about 35 years ago.

@thegringobaker 11 ай бұрын

@@WorkshopCompanion I've always made sure that my off switch is placed where I can hit it with my leg... I don't need to let go off anything to shut the saw off in an emergency (which, thankfully, I've not had yet).

@WorkshopCompanion 11 ай бұрын

@@thegringobaker There are good arguments for a knee switch, but there are also some against. The switch is not in your line of sight, so there's a chance you'll miss it on the first kick. And you have to take one foot off the ground, so you're off balance for a second. That can be dangerous as well. I advise students to use the set-up that works best for the way they work -- normally, the set-up with which you feel the most comfortable and confident.

@thegringobaker 11 ай бұрын

@@WorkshopCompanion Yes, there are valid arguments for both ways. I do agree that some of the under- saw switches are not exactly a safety feature as they are so far under the saw that finding them easily is sometimes not possible. The factory location on mine is very good... allowing me to shut it off with a simple knee bend... not foot raising required. I'd like to mention that i found the video entertaining and educational. I enjoyed it.

@lk-music Жыл бұрын

I needed to cut plastic once, I found my ceramic tile blade, dry, did best out of what tools I had available.

@WorkshopCompanion Жыл бұрын

I've used a tile blade, too, on occasion. Thanks for the tip.

@kevinthomson6324 Жыл бұрын

That square to the blade to line up your cut line is so simple it’s genius. I’m just bitter this whole time I never thought of it. At least now I have a excuse to go buy a small square.

@WorkshopCompanion Жыл бұрын

It's always good to have an excuse the buy a new tool.

@rickhayhoe Жыл бұрын

@@WorkshopCompanion Tell my wife about it!

@HepauDK 2 жыл бұрын

The last one only works if the miter bar is made of steel. If it's aluminium, you will have to hold the inclinometer to the bar yourself. My own inclinometer measures to 1/20th degree (Diesella IP54 bevel box, item no. 10453500). :)

@rickhayhoe Жыл бұрын

Wow! Who'da thought of turning the blade backwards?

@travispark2226 2 жыл бұрын

Good tips. I thought you were going to throw your hammer at the dog in the beginning though. Lol.

@roytyner5690 4 ай бұрын

you table saw angles a different direction form mine..i was picturing making a cut on yours and it looked not only impossible but scary as hell

@michaelmurphy4013 2 жыл бұрын

Great tips, learned something. Sounds like the bearings in your table saw need replacing

@WorkshopCompanion 2 жыл бұрын

Noted. Trying to find time to tear it down.

@markywellsboy2182 2 жыл бұрын

I thought the same. Sounds as rough as a badger's arse. Some good tips, though. I enjoy watching these. It's always nice to see a different solution to common problems.

@ypaulbrown 2 жыл бұрын

Good tips, but #1 could also be done by lining up to the kerf on your miter gauge to your mark if you mark piece on other side and have a fresh kerf. enjoyed this....cheers from an old geezer in Orlando, Florida....Paul

@acerjuglans383 Жыл бұрын

I was just about to say the same exact thing.

@ivanboschi3084 Жыл бұрын

I do the same with miter saw fence

@ivanboschi3084 Жыл бұрын

I do the same with miter saw fence

@lassanalibadu4317 2 жыл бұрын

Your wery xsalant I lay k your program. I am rohana in Sri Lanka thank you

@WorkshopCompanion 2 жыл бұрын

Most welcome.

@JohnRR Жыл бұрын

Hi, beginner here. Should i remove my riving thingy for tip 3?

@WorkshopCompanion Жыл бұрын

If your saw has a riving knife, there is no need to remove it (and it would be safer if your didn't). Ours doesn't -- it's over 60 years old and was manufactured before anyone knew what a riving knife was. Additionally, there are no retrofit kits that can be adapted to fit it. That is why there is no knife present in any of the tips.

@jimjackson5139 2 жыл бұрын

I have a question I have an older Craftsman table say and it does not have a kerf. Where would I go to find one or make one?

@WorkshopCompanion 2 жыл бұрын

I suppose what you mean by a "kerf" is a riving knife or splitter. If you google " sears craftsman table saw parts," you will find several suppliers of replacement parts, including Sears Parts Direct. They may be able to help you. I have an older (50+ years) Delta table saw. When it was made, there was no such thing as riving knives, and there are none available for it as an accessory. We recently made a riving knife from .105"-thick steel that will fit the old saw guard mount. (Most thin-kerf saw blades are .110" thick. The .105" steel provides .005" clearance if I mount my thinnest blade.) You may have to do something similar depending on your saw model and what's available.

@pumpkinheadghoul 2 жыл бұрын

QUESTION: Are you supposed to zero out your inclinometer on the table surface, or on the table insert? I always thought it was supposed to be on the table surface, since there's where most of your wood will be riding. However, you zeroed yours out on the insert. So which way is correct? Yes, I realize in a perfect world the insert would be perfectly flush with the table top all the way across, but I think we all know we just get as close as possible when adjusting our inserts to be as flush with the table surface, because in reality, as long as the insert is very close and not proud of the table top, then that's really what we're shooting for. I just want to know I'm zeroing out my inclinometer correctly for the most accurate blade angle I can get.

@WorkshopCompanion 2 жыл бұрын

There are two schools of thought on this subject. The first -- the "close enough" school you allude to -- is that you shouldn't use the insert because it may not be flush or level with the table. The second is that you should carefully align and level your insert so that you can confidently use the entire surface around the saw blade for measurement. I attend the second school. This not only lets me use the inclinometer close to the blade, I frequently employ a set of small engineer's squares, triangles, and height gauges for set-up. These would be useless if I couldn't trust the insert surface.

@Duckmanloren 2 жыл бұрын

Could you please tell me which Inclinometer you are using? I would like to by that one you have as well. I bought a different one and sent it back because it was all over the place as far as accuracy. Thank you

@WorkshopCompanion 2 жыл бұрын

Look at Neoteck. That's what I would buy today.

@patrickmclaughlin6013 2 жыл бұрын

on the inclinometer, do you think a cell phone could be used instead? I have an app on the phone for measuring angles like for a roof pitch, maybe not accurate enough?

@WorkshopCompanion 2 жыл бұрын

If you watch other videos, you'll see that I use a smart phone app called "Rotating Sphere Inclinometer" all the time. It's no longer available, but "iLevel" does just as well. I also have a magnetic back for my phone so I the stick it to tables and fences.

@gregcorrell396 Жыл бұрын

Hey do you have to draw an x on the board when checking fence for square

@WorkshopCompanion Жыл бұрын

I suggest you draw an X on one face of a board when checking that the miter gauge is square to the blade. It simply marks the board so you know which face is up or down after you cut through the X and lay the two parts against the fence. It also shows you that you're laying one cut end against the other. It's not absolutely necessary if you trust your memory. I don't.

@tornadokat 2 жыл бұрын

#1: Couldn't you extend the line drawn with the square all the way across the wood so it lines up with the kerf cut on the fence at the back and position the wood that way?

@WorkshopCompanion 2 жыл бұрын

Of course you can; there is more than one way to skin this cat. But the problem with using the fence as a reference is the slop or "lash" in the system. The miter gauge guide bar is a few thousand's of an inch smaller than the slot it rides in -- otherwise it would be impossible to slide. Furthermore, every saw blade has a small amount of runout. Because of these things, that kerf in the fence will grow wider as you make successive cuts. You can correct for some of this lash by consistently pushing the miter gauge to the right or left (choose one) as you cut, and this will help extend the usefulness of the kerf. But using a saw tooth as a reference will always be accurate.

@clowning76 Жыл бұрын

Hello i like your video but can i give you a tip. on 1:20 instead of marking the line on side of the blade and you have to use the straight square tool .. Mark line on the opposite side and align it to the cut out mark ..

@Boobtube. Жыл бұрын

what is the name of that tool u use at 5:14 to push the wood?

@WorkshopCompanion Жыл бұрын

A push stick.

@b3arwithm3 Жыл бұрын

For the tip #3, won't it burn the wood if we stop feeding it?

@dtom1145 Жыл бұрын

Tip number 2 assumes that the long edges of the wood are parallel to each other

@Richard-dh8ny 6 ай бұрын

Love the tips, but you lost me on the cross cut alignment. I was taught to always square cuts with blade or the miter gauges track. By aligning to your fence you have to know or assume the fence is square with your blade, but that may not be the case. Correct me if I'm overlooking something. :)

@osmanvincent1975 2 жыл бұрын

For tip #2, align the miter gage. Slide the gage out, slide back in upside down, with the miter part against the fence guide bar. Loosen and retighten the knob. Done, No fiddling.

@WorkshopCompanion 2 жыл бұрын

This presumes that the fence guide bar is square to the miter slot, and this is not always the case . It's not on my saw, but if it is on yours this would be a good way to go.

@gsp911 2 жыл бұрын

Then I learned something new again, thanks for that. # 4 - I usually make a sandwich with some scrap plywood on each side of the acrylic sheet, then you get a completely perfect cut.

@WorkshopCompanion 2 жыл бұрын

I can see how that extra support would prevent chipping. Good tip.

@huejanus5505 2 жыл бұрын

That method works well. The chipping is usually because the teeth on the backside of the blade tend to lift and make the plastic chatter.

@gregorymoreno3406 Ай бұрын

no riving knife? no push block or push stick?

@richardmoore7218 2 жыл бұрын

While you were drawing a line with the square you could have drawn it across the board and then lined the mark with the cut in the cross cut guide and thus eliminating the use of the square against the blade.

@WorkshopCompanion 2 жыл бұрын

I agree, the kerf in the miter gauge fence is a handy reference for a short while. But it widens over time due to blade run-out, vibration, and the lash in the miter gauge slot. The saw tooth retains its accuracy as a reference.