Man I didn't realize you worked for IIR. I've been watching your WRX videos for awhile too, lol
@TheeJayRed2 жыл бұрын
Something to note for anyone looking into these inlets - The Cobb inlet's BPV bung is slightly longer than the GrimmSpeed inlet's BPV bung. This can cause some BPV fitment issues depending on what charge pipe/BPV setup you're running. I was running the Cobb inlet, GrimmSpeed BPV, and OEM charge pipe and found out the the BPV was sitting crooked due to the Cobb inlet's longer bung. It wasn't extremely crooked, but enough to make me swap back to the OEM BPV for now and avoid any potential leaks. I chatted with GrimmSpeed about this and confirmed that the fitment is extremely tight with their BPV and inlet together, so the Cobb inlet's bung being slightly longer was enough to cause interference. Running a non-OEM charge pipe might help with this, but I haven't tested it yet. Regardless, I believe these are both solid options for aftermarket inlets. Just wanted to give a heads up for anyone that may be planning to run a setup similar to mine. UPDATE: I am currently running GrimmSpeed BPV and Cobb inlet with a Cobb TMIC/charge pipe kit which has a silicone coupler for the BPV/inlet/charge pipe connection. I was able to trim the BPV side of the coupler enough to make everything fit perfectly.
@ImportImageRacing2 жыл бұрын
Thank you for the solid additional information and taking the time to comment!
@TheeJayRed2 жыл бұрын
@@ImportImageRacing Happy to help!
@montano1712 жыл бұрын
Damn I just got both parts so I shouldn’t install the grim speed bpv I have your same set up
@TheeJayRed2 жыл бұрын
@@montano171 I’m now running a Cobb charge pipe with a silicone coupler, and the fitment is better. Not perfect, but better. I ran the GrimmSpeed BPV with the OEM charge pipe for a few weeks without issues, but I was uncomfortable knowing how crooked the BPV was sitting, so I took it out. I could see the metal-on-metal wear on both the BPV and the turbo inlet from where they were interfering with each other. YMMV, but any time there’s metal-on-metal where it shouldn’t be, I wouldn’t recommend it.
@xrateplaya2 жыл бұрын
I just installed the same setup as u Grimmspeed bpv and Cobb inlet. Did ur dam go down and were u getting consistent feedback and fine knock learn. My dam is currently at .250??
@OcDGM2 жыл бұрын
4:06 I would suggest placing the sticker somewhere visible under the hood, firewall, shock tower, etc. In CA, CARB EO stickers should be visible during an inspection, without it, you may have to argue your added on part, YMMV. Great comparison video!!
@haletomasson69911 ай бұрын
Great point
@drewmiller34472 жыл бұрын
I just installed the Cobb on my car I freaking love it!! Awsome video Cody!!!
@ImportImageRacing2 жыл бұрын
It's one hell of an upgrade! Thank you!
@haletomasson69911 ай бұрын
Thanks for the video. Cobb has hit the mark so far with previous modifications. So I feel confident about going with cobb for the turbo inlet. Any advice for boost controller's?
@ImportImageRacing11 ай бұрын
Grimmspeed 057041 is the way!
@qrtrscale2 жыл бұрын
Thanks for the review. Just installed the Cobb and finally broke my oem one after messing with it so much (caused by separate bpv and charge pipe installs -- I think the breakage of the oem part is self-inflicted).
@BADHABITSem Жыл бұрын
I just got the silicone one for 16 wrx. But I feel like I need that grimspeed one
@ImportImageRacing Жыл бұрын
Now is the time! Sale ends on Monday night!!!
@jakethesnake15032 жыл бұрын
here we go! comparison time
@willies_not_willys2 жыл бұрын
I always hate giving cobb my money but unfortunately my grimmspeed order had been backordered for several months. The grimmspeed seems to be a better, more finished design.
@maryburgess92932 жыл бұрын
more 17-21 gs inlets just got shipped out to us, we have plenty 15-16 here. Gs is corporate, you aren't really giving them your money.
@Sapient_Yam2 ай бұрын
Can you run the cobb inlet with grimmspeed bpv? I have a 2020 wrx with grimmspeed intake and bpv. Leaning towards the cobb inlet. Having a hard time deciding lol
@ImportImageRacing2 ай бұрын
Yes you can! Both GrimmSpeed pieces are compatible with the Cobb Turbo inlet.
@freewill_4042 жыл бұрын
Did you guys put an STi wing on the 22? Im debating on doing this but im curious how much work goes into it and the best way of doing it.
@ImportImageRacing2 жыл бұрын
Currently everyone we know that has done it including us has a gap towards the front of the Spoiler. The trunk has a natural curve unlike the VA WRX. We are hoping to come up with a solution
@pumpkinspicelatte17312 жыл бұрын
Do you have the Cobb Inlets instock because Cobb last I checked listed them backordered
@ImportImageRacing2 жыл бұрын
Yes 24 right now
@levi8592 жыл бұрын
Can you do a video on what fuse to pull or what to unplug to get rid of the vehicle Dynamics control and the traction control please?
@levi8592 жыл бұрын
On the 22 wrx
@aPanini10 ай бұрын
Am I the only one who swatted at the nat on this finger at 2:01? lol
@28darkrage Жыл бұрын
Can you go over in more detail what you talk about at min 2:30. I would like to see how you remove the PCV connector from the hose
@28darkrage Жыл бұрын
kzfaq.info/get/bejne/Z5xmg9CFrLG-oqM.html goes over removing the hose!
@trentmarr24059 ай бұрын
You state that you can do the 15 on 17+ but can you do the 17+ on the 15? And how would this be done, I bought the wrong one:/
@lawrence_lee.2 жыл бұрын
I just picked up a use cobb 1
@squirrelzar2 жыл бұрын
Is this upgrade a preventative/reliability upgrade over the stock plastic? Or are there any potential power benefits from the smoother airflow these would theoretically provide?
@FunTimeWithSouls2 жыл бұрын
The plastic will break very easily. My buddies cracked after only 5 months of owning it, it was a new car too.
@ImportImageRacing2 жыл бұрын
Yep. The main selling point is to replace the very commonly broken stock one with a durable cast replacement.
@Booker5222 жыл бұрын
Is Grimmspeed one in stock yet? 😢😢😢
@maryburgess92932 жыл бұрын
yes, the links are above click show more
@xil3ntkha0s2 жыл бұрын
It’s cool that Cobb got theirs approved but does it really matter? Isn’t the GS inlet basically a more durable factory replacement? I forget if tune is needed after installing it (stock or not).
@ImportImageRacing2 жыл бұрын
They will both do relatively the same thing. And neither requires a tune. The cobb one has some advantages over the grimmspeed one for someone planning to utilize those advantages, but at a slightly higher price.
@xil3ntkha0s2 жыл бұрын
@@ImportImageRacing I got that part I just wanted to know if having the part approved by emissions group really meant anything for the exact reasons you listed
@deanthakid9803 Жыл бұрын
So I want to buy fb blue turbo and I'm still running stock inlet, can any turbo be mounted to these ?
@Beatcheeks896 ай бұрын
Need a tune for a turbo inlet ?
@ImportImageRacing6 ай бұрын
While a tune is not “required” for this turbo inlet upgrade, some performance gains will be left on the table unless coupled with a tune. But replacing your OEM turbo inlet with a piece like this is always a great idea!
@pumpkinspicelatte17312 жыл бұрын
So have they had any issues with the Cobb Inlet on the 17-21s leaking at the PCV hose inlet that gets I guess kinda rigged down by a clamp connection, so did they have leaking there that they added the clamp?
@ImportImageRacing2 жыл бұрын
No issues
@RobHTech Жыл бұрын
Why's the vid all blurry? I like these comparison vids. Very helpful. I'd say that the Cobb is just better all-around and better designed, more practical.
@stevenknows1762 жыл бұрын
Could you use a grimspeed ebcs with the cobb inlet? Will it fit as flush as it would with the grimspeed inlet? Thanks in advance
@chocOneOOne2 жыл бұрын
I recently had my engine rebuilt and as part of it I upgraded to the Cobb Turbo inlet to mate with a new turbo, anyways, I'm running the Grimspeed ebcs with this part as well, so you'll be fine.
@holeshot262 жыл бұрын
i can see on this vid the grimmspeed is much better quality forging & machining. plus cobb changing the size will disrupt the stock map, meaning you would require a tune! and i bet those inserts for the ports are plastic, so another way they cut manufacturing costs yet jack the price up! I'd choose grimmspeed over cobb for ANY parts on my subie!!!
@ImportImageRacing2 жыл бұрын
The Grimmspeed inlet is very nice! Can't go wrong with that choice. However neither one requires a tune and the inserts for the ports on the Cobb inlet appear to be billet aluminum.
@MrDIJEN152 жыл бұрын
I need one but the BIG question is are both brands in stock ready to ship? If so I will order right now.
@ImportImageRacing2 жыл бұрын
Both are here now ready to ship. Link In description.
@MrDIJEN152 жыл бұрын
@@ImportImageRacing already ordered. Thanks!
@ImportImageRacing2 жыл бұрын
@@MrDIJEN15 thank you for your business!
@IImTaco262 Жыл бұрын
Would I be able to use the Cobb EBCS with the GS inlet?
@ImportImageRacing Жыл бұрын
Yes you sure can!
@javalideli2 жыл бұрын
Will either of these work with the Mishimoto intake?
@ImportImageRacing2 жыл бұрын
Both should work!
@christopherrogers8316 Жыл бұрын
does it matter what turbo i end up going with ? these will work with any turbo?
@ImportImageRacing Жыл бұрын
They work on any standard size turbo. Ie boost lab. Oem. Forced performance. Tomioka. If you go wild down the road and do an ets rotated kit it will not work. But you can achieve 550hp on a boost lab so you should be just fine!
@christopherrogers8316 Жыл бұрын
@@ImportImageRacing damn! I'm trying to pick the biggest/ highest power oem turbo, which would you go with? I don't have access to ethanol:(
@christopherrogers8316 Жыл бұрын
@@ImportImageRacing ?
@ImportImageRacing Жыл бұрын
@@christopherrogers8316 www.importimageracing.com/products/bl-0654-8fa20-boost-lab-td06sl2-54x-turbocharger-for-2015-subaru-wrx-fa20 buy that one. It’s on sale and works with both inlets.
@mohamedsiddiqui3932 жыл бұрын
Does the Cobb one support a GS EBCS?
@ImportImageRacing2 жыл бұрын
They don't advertise it but if it fits the stock one it will fit the Grimmspeed EBCS, you will just need to reuse the screws that come with the grimmspeed ebcs.
@phdavid42 жыл бұрын
Is there a replacement for the bypass coupler?
@ImportImageRacing2 жыл бұрын
The small hose that you see with each kit is a new hose to attach the bypass valve.
@phdavid42 жыл бұрын
@@ImportImageRacing yes but I’ll like to have a replacement since I mess mine up. So are there any replacements for the bypass coupler?
@jonshuacaceres9828 Жыл бұрын
am I tripping or is this the same guy from Street Inspired channel on YT??
@ImportImageRacing Жыл бұрын
Same Cody
@WedgewoodGarage2 жыл бұрын
Will the grimmspeed ECBS fit onto the cobb inlet?
@ImportImageRacing2 жыл бұрын
Cobb hasn't confirmed fitment but it fits thr stock ebcs so it will fit the grimmspeed the only thing you may need is different sized screws
@qrtrscale2 жыл бұрын
Yes, but you need to source shorter screws than the long set Cobb provides.
@WedgewoodGarage2 жыл бұрын
@@qrtrscale I got it to work.. had to dig up an old bolt kit I bought on Amazon a while back in order to find some that fit right.
@willies_not_willys2 жыл бұрын
Just cut the bolts down about 1/8" or so and it fits.
@Marselino19962 жыл бұрын
Does this fit the 22 Wrx?
@ImportImageRacing2 жыл бұрын
It does not. The 2022 wrx already comes factory now with a cast inlet so you don't have to worry about it breaking. I'm sure there will still be upgrades soon!
@lawrence_lee.2 жыл бұрын
Can the new ots stage 2 map work with grimsspeed boost controller