Caline: CP-60 Wine Cellar Bass Driver DI Pedal: Technical Review & Teardown
Рет қаралды 13,543
2 жыл бұрын@jobass Thank you for demoing this pedal!
• Caline CP-60 Wine Cell...
This pedal was given to me by Caline Technologies as a thank you for helping out with the CP-81 voltage/noise issue. This is my review of the pedal. This pedal is actually an awesome, inexpensive, & useful preamp DI pedal!
There is an RC4580 op amp driving the XLR, a 4558 op amp driving the 1/4" buffer circuit, and the drive circuitry is two TI074C quad op amp chips. All very good quality parts!!
This is not a true bypass pedal, contrary to what the website says. You need 9 volts powering the pedal in order to pass any signal through, even if the pedal is disengaged. The 4558 op amp runs the buffered 1/4" in/out, and the footswitch bypasses that circuit from the drive circuitry. It's not a big deal, but in the traditional definition of "true bypass" this pedal is not.
The XLR is a genuine electronically balanced DI output. There is no ground lift switch because Pin 1 is isolated from the case. The DC negative is also isolated from the case. This may explain why a switch was never part of the design. The 1/4" jacks are grounded to the case, and there is about 11 kohms resistance between DC ground and XLR pin 1. This is typical for the design.
I would say this pedal is a good clone of the Sansamp Bass Driver DI pedal, maybe not as gritty or have as many features. It is a clean preamp with plenty of flexibility in tone control for a two band EQ that boosts and cuts. It def has cabinet speaker emulation on the XLR which is a nice feature.
Bottom line, buy this pedal!!
@ilioscio 6 ай бұрын
Thanks for doing a more technical review of this pedal, great video.
@Bassguitarist1985 6 ай бұрын
Thank you!
@malcolmevans2663 2 жыл бұрын
Thanks for doing this video. It's great when we get a chance to see how it's put together internally. I've been looking for a bass preamp and this seems a good budget choice
@Bassguitarist1985 2 жыл бұрын
Thank you for watching! Yes def a great budget preamp!
@arnlmndza 2 жыл бұрын
Great content.
@N8oRMusic Жыл бұрын
I have one. Loooove it. End of story.
@kyon_03 Жыл бұрын
Thanks i just ordered this preamp for my gf bday
@Bassguitarist1985 Жыл бұрын
Cool stuff Happy Birthday to her!
@gorillafunk725 Жыл бұрын
Check out Bass The World. They love fancy and very expensive gear & they also give it the thumbs up. Love the fact that you show everybody what's under the hood. Great not "cheap" as that has negative connotations. I prefer inexpensive DI. Thanks for sharing 👍
@jmaguilarr 2 жыл бұрын
Muy buen , ttecnico, analisis
@raimundolanas4273 2 жыл бұрын
Great video! thank you so much. I have a question: From what I understand, these so-called 'preamp' pedals for guitar and bass are not actual preamps, in that they don't raise the guitar signal to line level, they seem to be more of a tone shaping device than a traditional preamp. Would that be an accurate description and can you comment on that? Thank you
@Bassguitarist1985 2 жыл бұрын
Yes you are correct, tone shaping. The 1/4" is instrument level, and the XLR out is mic level. You need to plug the XLR into a mixer to get the line level you want.
@GustavoZepeda 15 күн бұрын
In some specs info on the internet mentioned there is a cab sim circuit included for XLR output, is that true?
@minhthanhdang8409 2 жыл бұрын
Hello man. I have a problem with the caline cp60. I use home recording by plugging bass into the cp60 and into the behringer umc22. At my own house the sound is noisy as hell but with the same setup (bass>cp60>umc22) in my friend's house there is almost no hiss. Im not a engineer so i dont know which one is defective.
@Bassguitarist1985 2 жыл бұрын
It could be dirty power at your home.
@rcb_matt Жыл бұрын
I sold my Sansamp BDDI thinking I was done with preamp / DI pedals. Ended up wanting to add a little grit to my Markbass combo so I bought one of these. I have ran it into the front end and the effects loop. It sounds great either way. I do wish it had a phantom power option but... what would you expect for $40.
@Bassguitarist1985 Жыл бұрын
Exactly! Its a budget clone pedal based on the sansamp. Very useful for the price! No complaints here!
@rcb_matt Жыл бұрын
Update lol! Just bought the Ampeg STG-DI. It quickly jumped into the number one spot.
@gomes-fonseca 6 ай бұрын
which you prefer? ampeg stg - di or caline? the caline is better that sansamp? or sansamp is very very very better?@@rcb_matt
@gnatfreeman2184 2 жыл бұрын
I have this pedal and xlr output is very weak but the 1/4” is fine. Any thoughts?
@Bassguitarist1985 2 жыл бұрын
Weak as in low output volume? Are you going atraight into a mixing board? Gain set right?
@SisterRose 4 ай бұрын
i just wish they put battery slots in this! when i'm at my parents i don't really use power supplies so I have to use a HB Powerplant, it's mostly pretty good but I had to get a new one as the old one was noisy and stopped working so I don't want to over use this one. I got the Caline Bass Overdrive for the art and it's kind of meh, probably a cool single use pedal but I need something for my very dry sounding HB Amp
@Bassguitarist1985 Ай бұрын
It's a great sounding mid scoot pedal and can work for various playing styles and genres of music but it's not for everything. Some may find it bland others may find it very useful when they add other coloration from their amplifiers in conjunction with this pedal.
@robertfeynman3174 Жыл бұрын
Hi my man Do you think this is a better purchase for bass vs the Joyo American/Caline Americana?
@Bassguitarist1985 Жыл бұрын
I would say that this is a better purchase for bass guitar then the Americana. I haven't tried that one yet but I would question if it retains the low end of bass. If it doesnt you might need to run it through a parallel mixer to mix the pedal and dry signals
@alex_xro 2 жыл бұрын
i think you posted in pedalboards of doom? nice review
@Bassguitarist1985 2 жыл бұрын
Yes, Thank you for watching!
@chrisfit 2 жыл бұрын
Could you do their other bass pedal DI as well? This is a great video thanks! Subbed
@Bassguitarist1985 2 жыл бұрын
Which one exactly? The CP-59?
@minhthanhdang8409 2 жыл бұрын
@@Bassguitarist1985 yes please! Im very curious
@Bassguitarist1985 2 жыл бұрын
@@minhthanhdang8409 unfortunately that pedal is no longer available in the United States. I would have to import it from another country and the cost would be prohibitive. :-(
@Bassguitarist1985 2 жыл бұрын
@@minhthanhdang8409 caline is sending me the CP-59 Press Pass to review. Will be in the next few weeks
@jcisme 2 жыл бұрын
Thanks for the great review.. Any idea how much gain this has ? Does it have enough juice (while still clean) to drive a power amp from its 1/4" jack ? The practice area has an old Fender BXR300 that I bypass the preamp on.
@Bassguitarist1985 2 жыл бұрын
The output is instrument level, not line level, so I would say no it does not have enough gain. You need a small mixer to run in-between it and the power amp.
@jcisme 2 жыл бұрын
@@Bassguitarist1985 Thank you..
@toddlangworthy1361 2 жыл бұрын
What about the xlr output? Would that drive a power amp? Very nice review!
@Bassguitarist1985 2 жыл бұрын
@@toddlangworthy1361 it might. Ill have to check it out
@alex_xro 2 жыл бұрын
if you connect both outputs you get the same signal on both?
@Bassguitarist1985 2 жыл бұрын
Yes on the 1/4" and XLR. Only difference is one is unbalanced and the other is balanced
@thebassgum Жыл бұрын
Hi i just purchased the pedal, the Harmonics knob what does it do? Is it Mid or Like Presence? Tia Nice review as well
@Bassguitarist1985 Жыл бұрын
Harmonics is like a treble boost and mid scoop all in one. Least to my ears
@thebassgum Жыл бұрын
@@Bassguitarist1985 Oh ill play around with it more - Thank you! I subbed also
@Bassguitarist1985 Жыл бұрын
@@thebassgum appreciate that! Thank you for the support!
@KLLEBERBASS 5 ай бұрын
Eu uso no forró
@aryopratama4622 4 ай бұрын
Hi man.. i had bass with active onboard preamp.. do i still need this pedal? Does it make the tone better?
@Bassguitarist1985 4 ай бұрын
It gives you a different tone it doesn't necessarily make it better which is subjective. You likely have a 9 volt or 18 volt active two band or three band EQ. That alone is very powerful of a tool. This pedal will do a much more detailed EQ curve than just a 2-3 band giving you a more mid scooped but mild overdrive tone. Check out my other demo video on my channel about this pedal that will give you an idea of how it sounds
@lucasnich 2 жыл бұрын
Great video! I bought this pedal recently, and it has some noise, both with the power supply or the 9v battery on. The noise stops as soon as I touch the pedal casing or the switch. What could be generating this noise?
@Bassguitarist1985 2 жыл бұрын
The 1/4" jacks are not making contact with the case properly. You may need to scrape some paint around the jacks so its bare metal under the washer. That should ground the case when you have it plugged into the amp. Whats your whole configuration?
@lucasnich 2 жыл бұрын
@@Bassguitarist1985 It worked! Thank you so much! I plug my bass into the DI and then straight to my interface or my amp through the 1/4". I was getting noise from both, and thought was an issue with my power supply.
@Bassguitarist1985 2 жыл бұрын
@@lucasnich very cool! Glad it worked out! No noise? Quiet now?
@lucasnich 2 жыл бұрын
@@Bassguitarist1985 yeah! no noise, at least the ground noise. just the single coils noise.
@tiantugs Жыл бұрын
@@Bassguitarist1985 hello, is it the input jack/jack socket that I should scrape? or is it the cord itself?
@RobCmusic 2 жыл бұрын
Is there more likelihood of ground noise if using this pedal as a DI only with no connection to an amplifier? That is how I would most likely be using it.
@Bassguitarist1985 2 жыл бұрын
Little chance at all. If you have other pedals and the PSU has a ground reference it should be okay. The XLR pin 1 is lifted so there would not be any ground loops
@RobCmusic 2 жыл бұрын
@@Bassguitarist1985 Thanks for the quick reply. I'd be powering it with a powerbank/USB to 9v converter most likely or just straight from a 9v battery with the included battery clip. Should be ok I guess.
@Bassguitarist1985 2 жыл бұрын
@@RobCmusic yes, the current draw is about 30mA. Very low and should be just fine!
@rastafaray666 3 ай бұрын
hey i have problem with this pedal. at 5:10 you taking about this jackoutput. How to fix this. i have noise and hums when effect is on
@Bassguitarist1985 3 ай бұрын
The metal collets for the 1/4" input and output jacks need to contact the case in order to be grounded. Otherwise this is what I found causes the noise. Just scrape a little bit of the powder coat paint around the edge of the jack hole and then reinstall the collet with the washer. It should be enough to bond that jack to the case and stop the buzzing.
@rastafaray666 3 ай бұрын
@@Bassguitarist1985 ok so i must to unscrew all take the electronics little bit out, take the metal jack collar out and scrap the yellow paint in this place where os this ring of 1/4 jack? And what is the washer? Xd
@Bassguitarist1985 3 ай бұрын
@@rastafaray666 The washer is on the collet itself I don't think it's removable, and yes you are correct on the rest
@mindgames11 Жыл бұрын
also, is the XLR protected from phantom power?
@Bassguitarist1985 Жыл бұрын
Yes there are decoupling caps on the hot/cold pins after the opamp outputs to block VDC. Phantom power wont harm the pedal.
@candrabalimirage 10 ай бұрын
"Amazing !!" You Knew all the inside component-part like IC and etc. You are understand about electronic-component. Not many youtube-pedal-reviewer as Smart as you
@Bassguitarist1985 10 ай бұрын
About as gear head as one can get!
@MartinMartin-yi9to 11 ай бұрын
It would have been amazing if they'd kept the XLR 48v powering option on this pedal.
@Bassguitarist1985 11 ай бұрын
Certainly would be a nice feature but they remove that and also reduced the amplitude of the XLR to instrument level instead of line level. It would not be able to drive a Poweramp on its own without a mixer in between.
@MartinMartin-yi9to 7 ай бұрын
@@Bassguitarist1985Audio lesson #1 : A DI is not line level at the DI's output. You need a pre-amp to bring it up to line level. The XLR output on the CP60 fonction is a DI output.
@Bassguitarist1985 7 ай бұрын
@@MartinMartin-yi9to Yes correct that is what I said in my previous comment. Many people seem to mistake this pedal as a preamp pedal but it is not. A preamp denotes a line level output, a DI box denotes instrument level out, meaning it requires an audio mixer with a preamp to boost the signal to drive a power amp.
@joaomarcos5055 5 ай бұрын
Quer dizer que esse pedal não é um pré amp?
@candrabalimirage 10 ай бұрын
Subscribed and Like #198th... Thanks for your video
@Bassguitarist1985 10 ай бұрын
Thank you for subscribing and the support!
@WilDBeestMF 2 жыл бұрын
For a second, I thought it was sitting on breadboard 😂
@Iyannnn17 Жыл бұрын
Does it have a cab sim? Or just a pre amp? Thank you in advance
@Bassguitarist1985 Жыл бұрын
Its a DI box more so really. The XLR cannot drive a power amp without first going through a mixer. No cab sim, but the mids are scooped out and has a high treble attack like the Sansamp
@Iyannnn17 Жыл бұрын
@@Bassguitarist1985 thank you very much so i must use some cab sim when im goin direct at the house/mixer, and this pedal for tone shaping purpose only? And btw i took you advice for scraping the paint on the jack outputs and it helps a lot on the noise issue 🙏👌 more power God bless from Philippines 🇵🇭
@Bassguitarist1985 Жыл бұрын
@@Iyannnn17 Ian, I would say you don't really need a cabinet simulator for this pedal as it definitely already has tone shaping before you start making adjustments with the knobs. Give it a try without it and see how it goes you can always add a cab simulator later. Yes it's a small oversight with the paint scraping at the factory. The case needs to be grounded by the amp.
@EadgCrunch 2 ай бұрын
Hi. Does it color signal from DI XLR? I need my signal go through to my amp combo for monitoring, and clean neutral signal from xlr DI to my sound card.
@Bassguitarist1985 2 ай бұрын
It does color the signal through the DI yes.
@EadgCrunch 2 ай бұрын
@@Bassguitarist1985 But if I turn mix knob all the way down. Will DI XLR give me clean and neutral signal?
@Bassguitarist1985 2 ай бұрын
@@EadgCrunch it would yes, but no drive signal on the 1/4" essentially acting as a direct box. Why use it at all at that point? You would need a direct box for the clean signal while monitoring through your amp with the Wine Cellar using the drive channel
@EadgCrunch 2 ай бұрын
@@Bassguitarist1985 Thanks for your reply! I’ve got an old audio interface with broken monitor button. So I don’t have opportunity for direct monitor through my studio monitors, only with slight latency from ad/da conversion. I have a bass combo. So I decided to monitor my bass through my bass combo. Insert my bass in to Wine Cellar 1/4 input and output it to bass combo from another 1/4 output for monitoring and record clean neutral signal from XLR DI output into my DAW for later processing. Will this work? Thank You.
@Bassguitarist1985 2 ай бұрын
@@EadgCrunch that will work yes, and if you want to preamp it through the pedal with the drive tone you can do that too
@mindgames11 Жыл бұрын
those arent "ti074". those are ST microelectronics and the series is TL07X. The 072/082/74/84 are standard JFET op amps. that and the NE5532 are almost all ya need. oh and the 07X are lower noise than the 08X. the 06X series are low-power consumption. I wish you popped off that XLR jack and took some photos. I've been trying to reverse engineer/get a schematic for one of these without buying it. I feel like it's a clone of the sansamp
@Bassguitarist1985 Жыл бұрын
It is an exact clone. I dont have the schematic. I could ask them. Thanks for the info!
@dreik4302 5 ай бұрын
Hello! Do you have a video explaining how to do this ''scraping''? I bought a pedal like this and it has a buzzing/noise.
@Bassguitarist1985 5 ай бұрын
I mention this in the video you need to scrape around the cutout where the quarter inch jacks are so that when you thread in the outer metal bushing it will make contact with the case. This will prevent it from having a floating ground causing noise.
@dreik4302 5 ай бұрын
Do I need to open the pedal to do this scraping or do I just need to loosen the ports on the two external connectors to do the process?@@Bassguitarist1985
@Bassguitarist1985 5 ай бұрын
@@dreik4302 no all you need to do is remove the metal bushings on the quarter inch input and output jacks. Scrape a little around just enough where the washer contacts directly with the case ground and then tighten back snugly Don't over tighten since the threads are plastic. That should hopefully solve your buzzing issue
@dreik4302 5 ай бұрын
Do I need to scrape so that the entire washer is in contact with the housing? I scraped both sides, but the buzzing/noise remains. Do I need to do it on the source connector too? In this case, do I need to open it?@@Bassguitarist1985
@Bassguitarist1985 5 ай бұрын
@@dreik4302 input and output 1/4" jacks. Make a video with the noise. What is your exact setup?
@jefabel5252 2 жыл бұрын
Hi, and first, thanks a lot for the video. I am pretty interested to get one of those as well but I would like to ask a (maybe stupid) question. Is there a possibility to plug headphones in that pedal to practice at home…? Thanks to anyone who is going to answer me…! 😉😊 Best regards, Jef.
@Bassguitarist1985 2 жыл бұрын
Yes, but you would need a separate headphone amplifier connected to the pedal. Very easy.
@jefabel5252 2 жыл бұрын
@@Bassguitarist1985 thanks a lot. I’m going to try a find something like that…! And thanks for the very fast answer… 💪🏻🙏🏻🍀
@Bassguitarist1985 2 жыл бұрын
@@jefabel5252 there are many options out there in terms of headphone amplifiers. I have a cheap Douk Audio U3 off Amazon and it works great for applications like this. More advanced ones have built in EQs for example. Best of luck!
@jefabel5252 2 жыл бұрын
@@Bassguitarist1985 ok, thanks again for your help. I’m on a new quest…! 😅 Stay safe… 🍀
@Bassguitarist1985 2 жыл бұрын
@@jefabel5252 you as well!
@turbo_wrath 7 ай бұрын
can u use 2 outputs? 1 xlr going to PA and unbalance going to bass Amplifier?
@Bassguitarist1985 7 ай бұрын
Yes
@turbo_wrath 7 ай бұрын
@@Bassguitarist1985 Nice...thanks..
@turbo_wrath 7 ай бұрын
just to be clear.. two outputs at the same time..
@Bassguitarist1985 7 ай бұрын
@@turbo_wrath yes
@charlieburns1385 4 ай бұрын
Why use these instead of amp settings??
@Bassguitarist1985 3 ай бұрын
Some may not want to use an amp but only a pedal board through the PA
@xtremeboy851 11 ай бұрын
hi,... which is better caline cp60 or behringer bdi 21? thanks
@Bassguitarist1985 11 ай бұрын
I don't have experience with the BDI21 but id expect its a similar clone design of the tech 21 driver.
@xtremeboy851 11 ай бұрын
@@Bassguitarist1985 i want to know in both noise case. Which one is lower in noise case 🙏🏽
@Bassguitarist1985 11 ай бұрын
@@xtremeboy851 can comment on the BDI21. Never tried it. I do have another video where you hear a DI mixer feed of the Caline CP60
@xtremeboy851 11 ай бұрын
@@Bassguitarist1985 can you give me a recommendation the best one cheap preamp d.i?
@xtremeboy851 11 ай бұрын
I used sansamp and mxr bass d.i before! I need versatile sound with punch low 🙏🏽
@datle1402 Жыл бұрын
What's the value of 1/4" output impedance?
@Bassguitarist1985 Жыл бұрын
I chatted with you on FB. I assume 100k, don't have the schematic. I can ask my Caline contact though.
@datle1402 Жыл бұрын
@@Bassguitarist1985 oh that's you! Thank you again for your contribution for the bass community!
@Bassguitarist1985 Жыл бұрын
@@datle1402 my pleasure!
@datle1402 Жыл бұрын
@@Bassguitarist1985 Oh, and by the way I have another question! I notice there's a difference (quite substancial one) between [MIX knob in zero position] and [bass directly into interface]. Also when I set my MIX knob to zero, other knobs still change my sound when I try tweaking them, which is pretty nonsense. Is this normal or my unit is defective? Thank you!
@Bassguitarist1985 Жыл бұрын
@@datle1402 i believe that is normal. I'd have to see the schematic to understand the signal routing better. I like the sound of the pedal though!
@hudsonfonseca7550 2 жыл бұрын
what is the frequency of the low?
@Bassguitarist1985 2 жыл бұрын
If I had to guess its around 120hz
@hudsonfonseca7550 2 жыл бұрын
@@Bassguitarist1985 I was looking for one with like 60hz
@hudsonfonseca7550 2 жыл бұрын
@@Bassguitarist1985 I was looking for one with like 60hz
@Bassguitarist1985 2 жыл бұрын
@@hudsonfonseca7550 TBH im not sure. I never hot a schematic for this pedal. If you ask Caline they may be able to tell you. It is a shelving type EQ from what my ears say.
@Acousic-AllCoverMusics 2 жыл бұрын
what can I do to reduce noise/humming on this pedal...I have this and its humming...thanks
@Bassguitarist1985 2 жыл бұрын
You may need to tighten the input and output quarter inch jacks. They need to contact the ground pin inside the jack otherwise it will buzz.
@Acousic-AllCoverMusics 2 жыл бұрын
@@Bassguitarist1985 can i solder a wire from ground pins to input jacks to reduce hum/buzz?
@Bassguitarist1985 2 жыл бұрын
@@Acousic-AllCoverMusics if you run a wire from the 1/4" jacks to the case, not the XLR pin 1, it should quiet the pedal down. The metal collars on the 1/4" are just barely long enough to engage the ground pin in the 1/4 jack itself. I had the same buzzing issue untill I tightened the collars up. The paint of the case also insulated the collars too. I scraped around the hole to expose bare metal in order for the collars to ground the case properly. That may help you too. Let me know if I can be of help. Post a video of the noise if you get stuck.
@Acousic-AllCoverMusics 2 жыл бұрын
@@Bassguitarist1985 ok ill try your suggestions first, if no fix...ill let you know...thank you for the quick response
@Bassguitarist1985 2 жыл бұрын
@@Acousic-AllCoverMusics def. I can make a video too to assist. The hum/buzz can be fixed.
@alphanumeric1529 2 жыл бұрын
I really wish this pedal sounded good. Did they use the incorrect taper on the pots? Like they went linear when it was supposed to be log, or visa versa? My drive knob does nothing until the last 1/8th inch, then it starts to drive, but the noise gets out of hand. For a bass head pedal, to run straight to PA, what is this pedal supposed to be clean driving? The mixer? Mixers, especially modern have quite a bit of clean headroom. It doesn't make sense to me that this would be intended to be a clean driver for bass. Of all the pedals I've bought over a lifetime, this is the one pedal where I questioned if the knobs/pots were actually connected to the circuit board, because of huge sweeps on the knobs, and several knobs in concert, with almost no change, or barely imperceptible changes to the bass sound. Okay, so the pedal has some quality opamps, and other components... It means nothing to me if the pedal itself sounds bad, undriven, no flavor..
@Bassguitarist1985 2 жыл бұрын
Depending on what you are looking for the pedal to do i guess. There are B20k pots in this pedal, so linear taper. If you listen on headphones the mids are scopped and the bass/treble is slightly boosted. There is a drive sound, but its not aggressive in the slightest. If you are looking for overdrive gritty tones this pedal wont do it well. I think the original intention of the engineer was to have a basic preamp pedal with a lot of headroom. There are other pedals in their lineup that would be a better choice for overdrive gritty tones. I can tell you that the knobs do have an audible effect on the tone. I agree the drive knob you need to turn up almost all the way to really get an overdrive distortion type of sound but it's not a very good one.
@Bassguitarist1985 2 жыл бұрын
Check out this sound demo. kzfaq.info/get/bejne/nKxglLibupe0Z40.html
@gomes-fonseca 6 ай бұрын
this pedal is analogic or digital? tks
@Bassguitarist1985 6 ай бұрын
Completely analog
@gomes-fonseca 6 ай бұрын
tks and the simulation of cab is only EQ and not I'R or any digital simulation, correct? tks@@Bassguitarist1985
@Bassguitarist1985 6 ай бұрын
@@gomes-fonseca correct
@gomes-fonseca 6 ай бұрын
friend, the sansamp bass driver di is analogic too ??@@Bassguitarist1985
@steveo7767 Жыл бұрын
No 9v power adapter? Wow, that's something that all pedals should come with new. That's something that is a must with me, no plug in power adapter no bueno.
@Bassguitarist1985 Жыл бұрын
Unless it's a specialized voltage other than 9 volts many pedals are not including them. The thought is that you will be putting them on your pedal board which should already have a power supply to run it. It's the same argument as a phone charger included with new cell phones, some of them don't include it
@Jack-fs2im Жыл бұрын
I ilke pedals that give you a 9volt clip.
@Bassguitarist1985 Жыл бұрын
They do come in handy
@oldasrocks9121 Жыл бұрын
It's a copy of the o.g. Tech 21 Sansamp
@Bassguitarist1985 Жыл бұрын
But with far less creature features, just the basics
@oldasrocks9121 Жыл бұрын
@@Bassguitarist1985 Nah, exactly the same, there's 3 versions of the black Sansamp DI, this is the same as the first. The smallest footprint VT Sansamp has the same 6 controls as the black one as well. Caline says Harmonics rather than Presence and Mix instead of Blend. It's a better copy than the Behringer, sturdier, quieter and nearly has the Sansamp's heavy stones. Worth every penny, just needs a paint job. 🙏👍❤️
@Bassguitarist1985 Жыл бұрын
@@oldasrocks9121 good info to know thank you!
Bassguitarist1985
Рет қаралды 3,9 М.
SOFIADELMONSTRO
Рет қаралды 73 МЛН
JHS Pedals
Рет қаралды 134 М.
ProfessorOnBass
Рет қаралды 10 М.
SOFIADELMONSTRO
Рет қаралды 73 МЛН