I want to thank you as well! Interesting how many people got the same problem. Bonus tip: The pressure with hands on the flex cable worked for me only for two days. And when I tried your tips nothing happened. I almost bought a new sub board and then I cleaned both connectors on this flex cable you mentioned with alcohol and a toothbrush and then the pressure worked again. The connection is really poor, the upper part of this flex cable (closer to camera) causes that the power button doesn't work. So when you remove the plastic in the upper part this button won't work for you. Pressure on both sides of this cable needed!

Fixed it. The lower (USB) board didn't make contact with the connector. I used some 1-2mm rubber with adhesive on it. Before: clean the connectors with isopropyl alcohol and compressed air. Using AccuBattery measure over 5A of current at charging. L.E.: The phone still works as new! It passes about a year now, and it's still strong. Turbocharge works nice.

Thank you for this video !!! All I needed to do was to put pressure on that 1 spot, you saved me money and time.

I had issues charging that appeared the day after upgrading to miui 14. Was kind of thinking about planned obsolescence and I stumbled upon this video that made me realize what was the issue. Thank you so much. I love this phone.

It worked for me too with 4 layers of insulating type cut to size. Yay! After repair, the battery on my son's phone had been run flat so I slow charged it up to 15% with a battery pack and then plugged the official charger in and it turbo charged up to 100% in about an hour. Fortunately I'd repaired my daughter's Honor 9 Lite a few times (screen replacements) so I had all the parts I needed including the T7000 glue. Thank you so much for this video.

Thank you! It works for me too. I peeled off the shell with a small microwaveable pillow heater.

Thank you for sharing the info! I got the same problem. :( And it came in the worst time as it was the case with others. :/

used this to figure out how to get it charging again, pressing in bottom fixes it ... i'm sure it wont last, but at least i have a fully charged phone for another day Edit: Did the full fix with layers of electrical tape and it's been working fine for a few weeks now

I have a very good tip for everyone with the same problem. I had the same problem, I guess the ribbon cable wasn't connected well. Instead of going through this whole process, I tried putting the phone glass side down on a table and start pushing on the back thoroughly and with a lot of force. The back is flexible and I guess I also applied pressure on the ribbon cable connectors through the back of the phone. When I tried charging again, it worked like a charm! The whole process took 10 seconds! At the same time, I could not have thought about trying this without this video as it revealed the possible issue and location of the ribbon cable, so a big thanks to MST!

Thank you for sharing this video. I have the same problem and like you, I put pressure on every corner and then the charging works. I guess is because I dropped it a couple times and something inside must have gone loose. Lol. Thanks buddy, you save my phone with this video. God bless!

works fine the solution, i pressure the metal pad with a piece of simcard... then works perfect the fast charge.

Just saved my phone myself after three tech shops denied looking into this phone. Thank you MST!

Mine waited 4 years to do this bad thing to me, even though it was well used, a lot of falls, including two broken rear windows. In short, I put 4 small pieces of Schaterton tape between the plastic part of the speaker and the connection of the cable to support it, my device was able to charge again easily I knew there was a known charging problem but I was never interested since I didn't have a problem, I thought it would be necessary to change parts or resolder something, but no it was easy and free ☺️

hey thanks for uploading this video! It really solved my problem, spent hundreds by repairing but none of the shop could detect the problem. Thanks a bunch!

Have to say thank you, my phone had exactly same problem, now fixed.

Thank you so much 🥰 Just finished from my phone disconnected the cable and reconnected it and now charging works great.

Thank you, the same problem! You saved me hero

Thank you for this' i was looking at vids to see why my phone was not charging. Then i tried what you said at start of video. I put presure on certain spots on the phone and it started charging i was litrally looking at new phones as well you just saved me £600+ thanks dude

Thank you very much!!!! It solved the problem for me. It was a very simple fix with the added pressure to the flex cable. Let's see if it fails in the future, but for now is very reassuring that the charging problem had a very simple explanation. Really liked your method on figuring that out. By the way, the adhesive on mine was a bit excessive and that made me doubt if it were to work out in the end, I had to apply heat for a good 5 mins in the entire edges of the phone until the cover was able to break apart with a bit of force.

tq so much for your video bro... now my phone already can charging like usually.. may god bless you...

Thank you so much for this video!! It worked for me 🤗

this worked, now waitng 2 months for the back cover tape. all my friends are just laughing at the mod :D but it works beautifully

hi! my phone have the same problem 2days ago then i saw this vid and tried to press the lower part of the phone and it works! seems like it is really the same problem as yours thanks a lot i have now the details of the problem

Love you bro, my phone have the same prob, i just have press on screen and backside, and now my phone charge again 👍

You are the best !!! Before 1 week i had the same problem with my Poco f2 Pro. When I asked the technical from MI service store about the fixed cost, he told me: "...the cost for repair the charging problem it is €50". I followed the instruction from your video and I repair my phone in a half hour and without cost 😃😃😃 Thank you man.

my poco f2 pro had the same problem and just done this. i think it works ! great ! thanks.

Dude you save my day and my money, I LOVE U MATE ♥

Tq so much.. my poco f2 pro "dead" almost 1 & 1/2 year. today.. i almost throw it away. for the last hope, i try to check online solution untill i saw your video tutorial. turn out, i have same problem with that unit. i apply pressure to that connector, and my phone charging. 🥰 now its work again & i decide to give it to my father. tq so much for ur tutorial. 🙏🏼

Thank you. It works on my phone

thanks mate this was very helpful 👍👍

Yoo make my day ! It so funny that first time I encounter this kinda problem , Thanks!

Thanks. This really saved me - although my phone now only charges to 87% and I'm not sure why but it won't go above that. Poor design from Xiaomi considering how common this problem appears to be from the comments.

Thank you so much! U save me a couple bucks and it was very funny to do it.

Thank you, long video but it helped me to charge it, I used a clamp and it works👍🏻👍🏻👍🏻

i have the same problem, i don't understand how the connection is not good one day ... But it works fine, thank you !

On my phone was same situation, that trick was help to me, thanks my friend 😂

Thank you!! This is such a helpful information 😢 my phone is not charging right now because of the same situation

Thank u very much for the video! I have applied the same solution and it's working well

you saved my life. thank you so much

Thank you. It worked

I go to the mall they just charge it and never explain and I forgot to test If charging but its late to watch this but still thanks I'm not going back they just want money their not honest.i checked it myself and its right their lose contact at that same spot after I touched then it works.I'm very thankfull this phone is going three years to me I'm glad I saved money from buying another phone.

when i met tjis problem i change charging port plate plus battery from aliexpress . i wery like this phone for his front camera :) i hope he will live long after repair at moment all is ok

Thx dear friend. It works like a charm

I placed a porous material, which is little spongy with the exact same way and it's still working fine after few days.

Save my money thanks dude 🙏🏼

Worked like a charm! Thanks a lot. Now my Poco is charging again without any problems. Saved me a lot of money. Still a good daily phone!

This worked for me too, thanks mate

thank you, you helped me, good job 👍

So after 19 months my Poco started having the same problem - I followed this instruction - 3 layers of tape - and it worked - thank you so much!

did this today, really helped!!! thx man

Thank you so much!!! God bless you!

Thank you sir you saved my day

Very usefull i had same problem

Thanks, it worked for me too

You save my phone (money too)

Worked, thanks

I did this, saved a couple bucks hehehe

I thank you thausand times. You helped me so much. It only was a loose cable. you are my hero 😁

Buen video , soy de Perú , tengo el mismo problema de carga . Que es esa pedazo de metal que pones para que haga contacto ? Es cualquier metal

Thank you very much

Thank you very much!

Followed the steps and it works! Thanks for making this video.

waaah thank you po huhuhu pinindot pindot ko yung likod gumana biglaa yehey

note good idea bro after a while problem is back jumper is the best sulotion

This happened to me today. I was worried that the usb port was damaged when I watched your video, I did what you said at the start, i put pressure on the phone and it charged. Thank you so much for the video

Thank you so much !

Thanks bro u helped me :)

Excelente!!!

THANK YOU :DDDD

Merci beaucoup

Thank's for your video after 26 month with my f2 pro i was thinking about buying a new one, now is charging again. But now i don't know why the vibrator make a very loud sound like a Cicada.

I fixed it like you showed and it works for me as well, so thank you! The only problem is that it now charges very slowly on a normal charger (a full night gives me ~50% charge at 5W) and it gets very hot on a fast charger, do you have an idea what it could be?

This worked on my phone only for a short time. Buying a new flex-cable would fix the problem and it charged at 2900mA

Woooow looks like a common problem on f2 pros

Merciiii 😊 Mon téléphone recharge 👍

Haha only faced this issue aft 2yrs of usage

tnxss i pressed and it works

Nice ❤️

Thanks for the solution! I was able to test it by pressing on the back, it works but it's a bit random. I'd like to repair your video, but I don't have any equipment apart from a precision screwdriver. Does the hair dryer solution really work? Also, can you advise me on a dismantling kit and the type of glue to use to replace the rear shell? Thanks in advance! :)

Merci beaucoup, je suis française mais j'ai compris, j'ai enfin pu réparer mon téléphone qui était comme neuf pour 0€

Thanks, i have the same problem with my poco F2 Pro. But, can i know what tools you use to heat dan remove back cover?

Hi MST, Thanks a lot for your video. I followed every step but it didn't work. I also replaced the flex cable and the charger board with no luck. I have a question about the tape/sticker that you are holding at 11:09. Unfortunately, I cut that in half when I was opening the back panel. Can it cause the problem not resolving after doing the steps? And how to replace it if it's important. Thanks a lot.

5:38 What is this sticker good for? I've completed your guide, changed the connecting cable and it works nicely now! :) But I forgot to put back this sticker at the timestamp. :( Will it cause any problem? Does it have a shielding function or it is just a normal paper? Seems to be a normal paper to me.

Why didn't the charging speed work for you?

Thanks bro, I did these steps and now it's charging properly, will I have the same problems again?

My bro, can u tell me what metal you put there? And what kind of adhesive wrap th metal? Thanks

I have a question. At what temperature does the adhesive melt?

May i ask what kind of screw driver that you used to open

i got redmi k30 pro zoom which generic to poco f2 pro.. my phone still can charge but sometime turbo charger not appear until i put off and put on again.. did your think this method can solved my problem too?? thanks..

Hii pls help me I need your help, the same issue happened to me It finally charged but the charging seems to go on and off, what to I do? It charges and then stop charges then stop

what glue do you use? thx

Hello, Qestion when therse that paper or smth 1angle is to main system and one to second I switched it ant it charges then but qeastion is it ok ? please answer fast as can becuse dont know if it wont blow up or smth :D

Can I put my main flex cable under the battery? just incase if the battery swell it wont tear the main flex cable upward.

THANKSS BROO, SAVE MY MONEY HAHAHA

When phone dont charge you got red light on top on?

Ehat type and brand of glue do you use to put the phone back together

Hi, what kind of glue you are using? Where I can get it from?

Thanks, this seems to have done it! lets hope it holds

all poco f2 pro have this problem or only some? I see a lot of people complain about this.

Warning!!! You are not supposed to take the camera cover off! It should remain on the phone!! Other than that, this tutorial was helpful and did fix the issue, or so far it seems. But there is some foam that seems to prevent bleed light and moisture from getting into cameras, which you are going to damage if you don´t leave the glass on the phone, meaning if you do what they did on the vid.