Yamaha 60HP Prop Seal Replacement | Yamaha T60 Outboard Output Seal Replacement

No video

Yamaha 60HP Prop Seal Replacement | Yamaha T60 Outboard Output Seal Replacement | Boats.net

Рет қаралды 29,496

Күн бұрын

Buy the Yamaha 60HP prop seals and O-ring here: bit.ly/Yamaha-6...
John will show you how to replace the prop seals on your Yamaha outboard in this video from Boats.net.
You don’t need to remove the lower unit to change the prop seals on your Yamaha 60HP outboard, but we’ve removed ours to take care of some other jobs. See how here: • Yamaha 60HP Gearcase R...
We’ll start by draining the fluid out of the lower unit. then , we’ll get to work removing the output shaft carrier. Once we’ve got it removed, we’ll tackle the oil seals. There are two, and they sit next to each other in the housing assembly. We’ll also replace the O-ring.
Then we’ll put it all back together again.
Once that’s done, you’ll need to refill the lower unit. Find out how to do that here: • Yamaha 60HP Outboard G...
Here’s a look at the prop shaft assembly in this diagram on Boats.net: See this diagram for a better look at the Yamaha 60 water pump kit and how it fits together: www.boats.net/...
Read how to do this job step by step: www.boats.net/...
VIDEO HIGHLIGHTS:
Draining the lower unit - 0:40
Removing the output shaft carrier - 1:25
Pulling the carrier - 2:25
Removing the oil seals - 3:40
Replacing the O-ring and seals - 4:10
Replacing the carrier assembly - 5:20
Find Yamaha outboard parts here:
www.boats.net/...
Talk to us:
Twitter: / boatsnet
Facebook: / boats.net
Instagram: / boatsnet
In the video we’re working with a 2003 Yamaha 60 HP 4-stroke outboard motor, but you may have similar steps for your Yamaha outboard. If you’re not sure whether these steps apply to your motor, leave a comment and we’ll get back to you.

Пікірлер: 13

@jtb2180 Жыл бұрын

Can you put link to buy the tools that was used in the video

@crispernator Жыл бұрын

Gday mate you make it look so easy with the right tools and knowledge , ive seen the other ways to do these seals and if you scratch that output shaft well you know what happens ,the right tools are great of you do it all the time and make the job so much easier .

@kal7393 Жыл бұрын

Would be helpful if you would have shown orientation of the input oil seals since that seems to be the biggest question when it comes to Yamahas and prop shafts.

@ericrittenhouse 3 жыл бұрын

Thank you for the tutorials. It gave me the confidence to do my own maintainance. Although I'd rather be on the water, getting the experience working on the boat has been great too.

@BoatParts 2 жыл бұрын

You'll save a lot of money learning to replace your own seals and water pump components.

@roughseas8952 2 жыл бұрын

Does the 60hp has the gasket on the gearbox....

@chunkybcharters Жыл бұрын

Awesome. Thank Sir.

@enduringpromise 3 жыл бұрын

It would be great if you would show alternatives from buying speciality tools or provide a place to rent tools when there are no alternative ways.

@justinthompson4285 3 жыл бұрын

I got a 90 Mercury how many ball bearings go inside of the spring in the dog clutch?

@DaveinNewport 2 жыл бұрын

Feeling a little daunted by the specialty pullers you use and how I would be able to get around not having them...would be cool to have sources for those. Thanks so much for your videos!

@dennisharrison4744 3 жыл бұрын

You know what your doing i just re sealed my 85hp the 2 under the water pump was in wrong acording to yamaha specs put all new seals and water pump eseast lower i ever put back on