Yamaha o1v96 v2 fader repair

Рет қаралды 12,668

3 жыл бұрын

Repairing a fader that won't go up anymore on the Yamaha 01v96 v2. Replacing a transistor is all it takes but finding the right one could be a little tricky. The whole repair is to do in about 30 min.
The transistors used came from ebay but are not always on sale. Follow the links below, if they are not for sale the alternatives will probably do fine as well:
For the 1181:
www.ebay.nl/itm/10pcs-2SB1181...
And the 1733:
www.ebay.nl/sch/sis.html?_nkw...

Пікірлер: 24

@torbenhellborn3175 3 жыл бұрын

Hello Tech - what a most clear and very easy understandable demonstration. Thanks

@steinarnerimehaug2979 8 ай бұрын

Check out details on testing and purchasing correct transistors in my video: kzfaq.info/get/bejne/oJmPZ7pexN_Sm58.htmlfeature=shared

@vinylchallenge5572 2 жыл бұрын

from my experience: you need to replace the fader and the transistor(s). The Faders position sensor gives out unsteady values, motor driver(=transistors) overheats. if fader(s) seems to make noise (hum like) after a motorised move = replace both

@creativewithtech3239 2 жыл бұрын

Thank you, that is some very valuable extra information!

@musicanivel 21 күн бұрын

TRANSISTOR 2SB1181TLQ PNP 80V 1A y 2SD1733 NPN 80V 1A

@orquestacache1 3 жыл бұрын

Hello I need help I have a problem on the 01v96 with some channels of the table that stopped working, the signal input does not detect it. because it can be

@vinylchallenge5572 2 жыл бұрын

add: it is important to at least clean the Faders. in my most recent case: some faders did not move in both direction, but the transistors where ok, i could not detect a short. So i opend the faders: not complicated, you can find guides here. inside them, 3 contact points in the slider where completelly covered with dust. cleaned them, now they go fine again.

@mickeymarquez Жыл бұрын

Hi! Where I can find the guide to open the faders ? Thanks

@vinylchallenge5572 Жыл бұрын

@@mickeymarquez push the 4 lugs "into" the frame with a small pillars

@vinylchallenge5572 Жыл бұрын

@@mickeymarquez kzfaq.info/get/bejne/d62paqeDkrO3hqc.html

@FREDDYSOM01v96 3 жыл бұрын

hello friend all jewelry, I have a problem with the fader of my 01v96VCM the faders do not correspond according to what the table determines and neither the calibration, faders all new, when I put them to calibrate they go up very slowly it looks like this is getting to the engine alternating energy instead of continuous energy. I would like to know how yours was and what components you changed ...

@creativewithtech3239 3 жыл бұрын

During calibration the faders co up very slowly: that is normal behavior. Just wait till it finishes.

@neilmilne7208 3 жыл бұрын

Can you give details of the Chinese website and the types of transistors you used. Thanks.

@creativewithtech3239 3 жыл бұрын

Yes I'm sorry, I promised so in the video but forgot about it. The links have been added in the description. The transistors came form ebay. Not all are available but any similar will do fine. Good luck with the repair!

@torbenhellborn3175 3 жыл бұрын

. . . thanks for your self-humoristic comments . . 8.45

@chezlevisie 23 күн бұрын

Hi Tech, great video! Due to a fulltime job a time consuming hobby and a girlfriend.. Would like to ask if you by any chance live in NL and willing to fix mine? Greets Osheen

@creativewithtech3239 20 күн бұрын

Sorry maar die problemen heb ik helaas ook met daarbij nog dat ik volgens mij die transistoren die ik ooit had allang heb weggegooid aangezien de mixer alweer een paar jaar de deur uit is

@torbenhellborn3175 3 жыл бұрын

Hey Tech - just bought a used one on Friday. Somebody put in new fader's (so the seller told me) and since then the machine come up with a message right after start-up saying "faders need cali- bration" . . I press OK and as far as I know the mixer (after 2 days) . . they then work as they should. But nevertheless - calibration would'nt be a bad idea, would it ? Do you know how ? Best regards Torben, Denmark

@creativewithtech3239 3 жыл бұрын

A full calibration is always a good idea and it also shows if there are other faders likely to die soon (the usually are cause of a fader calibration error). Look at the manual how to start in calibration mode: I think it was starting with the inc and dec buttons pressed but don’t remember for sure (I sold my o1v96 a few months back).

@petersams5054 2 жыл бұрын

@@creativewithtech3239 Power up and hold ENTER