Yamaha Snowmobile Belt Tension Deflection

Рет қаралды 13,672

2 жыл бұрын

#yamaha #snowmobile Yamaha Snowmobile Belt Tension Deflection. How to adjust the tension/deflection on most Yamaha snowmobiles.
Get the parts I use below:
Suspension Spanner Wrench set: amzn.to/3YTqrJS
Snowmobile Ear Plugs: amzn.to/402JcM8
Stacool Scratchers: amzn.to/3HqLehH
Folding Saw: amzn.to/3kEBBTF
Kimpex Plug 993907: amzn.to/3HZLXXM
50/50 ready to use antifreeze: amzn.to/3WKODN6
Lock and Lube no leak zerk adapter: amzn.to/3xVemZv
Yamalube 2S: amzn.to/3FhsWyQ
Chain case oil: amzn.to/3vnlZ8F
DISCLAIMER: Not liable for anything you attempt after watching one of my videos. Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional charge to you! Thank you for supporting my channel so I can continue to provide you with free content!

Пікірлер: 13

@randykish8242 2 жыл бұрын

Nice informative video. I have a 2002 Yamaha SX Viper and this is exactly correct. I also agree with Scott White's suggestion to flip the wear plate over if needed. I could add the Service Manual specifies a sheave width of 35. mm factory which is measured between the right and left sheaves at each of their ends. For anyone wanting to get picky on a clutch rebuild. And also when reinstalling the secondary the main axle bolt torque spec is 46 ft pounds. Happy sledding!

@scottwhite2379 2 жыл бұрын

If you dont have thinner washers, disassemble the clutch and flip the wear plate the screws hit on. After a few thousand miles, there is a groove worn into it. The new surface sometimes is enough to correct the spacing.

@thatalaskaguy Жыл бұрын

Great video, thanks for posting!

@janeycookevogt8703 2 жыл бұрын

Very informative.

@mixoum691 Жыл бұрын

thank you very much for the Q

@232K7 Жыл бұрын

👍👍👍

@cdharrison935 Жыл бұрын

Very informative video, thank you! I bought a replacement belt. (GATES G-Force). I am being told to ONLY use Yamaha OEM belts. Did I just waste my $? It's for a '98 VMax SX 600 Twin

@MiloFarms Жыл бұрын

I have had good results with both oem belts and aftermarket. Just make sure you have the correct belt for the sled per the belt manufacturer.

@bob57786 2 жыл бұрын

Hi Milo farms. My 2007 phazer won't go into any gear (I backed it out of the trailer and now it won't move). It worked fine yesterday. I tried shaking the sled and everything. Any ideas?

@MiloFarms 2 жыл бұрын

My best guess is something is stripped in the reverse gear box or a bad reverse motor. You could study the parts schematic breakdowns to see how it works. I would try setting the sled flat and taking the drive belt off. Start the sled and let it idle and warm up. Try to shift it to reverse or drive and wiggle the secondary clutch by hand to see if it will engage into drive. If you can get it locked into drive and there are no loose parts in the gear box you may be able to ride it.

@jefaerts4207 6 ай бұрын

Can the washers (shims) just be removed instead of replacing with thinner versions?

@MiloFarms 6 ай бұрын

They can depending on how you need to adjust the spacing. You would either have no washers for a brand new belt or tight system or start adding washers as things wear.