Hi there. I have one of these engines in a generator I was hoping you might have some advice for me the engine was runny perfect it's been left for around 6 months and now won't start I have checked everything and one thing I have found that doesn't seem right is when cranking on the compression stroke the exhaust valve opens alittle then snapps shut like it's catching something on the cam. Have you ever had this l? Is there anything that pops to mind? Any advice welcome I'm out of ideas now
@okrishna76633 жыл бұрын
Thanks for ur video it used sir
@guypatts4943 жыл бұрын
I just acquired this diesel engine it had no shims how many shims does it require
@davydacounsellor4 жыл бұрын
Great vid thanks
@JoshKilen4 жыл бұрын
nice job, how do the rings have to be aligned? 120 degrees apart and what can't be aligned with?
@zippyzappyz4 жыл бұрын
yes!
@JoshKilen4 жыл бұрын
@@zippyzappyz ok, you didn't answer my second part that that question. do you mean the wrist pin that the first ring that can't be aligned with?
@zippyzappyz4 жыл бұрын
Josh Kilen yes, I answered yes as none of the ring gaps can be aligned with eachother, the best thing to google is yanmar l70 manual because it will show you exactly how everything needs to be aligned
@JoshKilen4 жыл бұрын
@@zippyzappyz thanks, but my engines are the 186FA which is a 10hp diesel, which is equal to the L100.
@zippyzappyz4 жыл бұрын
Josh Kilen the l70 manual should come up with all 3! The l48, l70, and l100! Your 186f will be equal to the l100!
@lintangluku50803 жыл бұрын
👍👍👍
@JustaCuriousity3 жыл бұрын
Hi, i have finally rebuilt 186F engine, it looks similar, but its weird that my engine failed to start. Injector is good, adjusted valves 0.15, any idea what i have done wrong? Thank you.
@JustaCuriousity3 жыл бұрын
It was the fuel pump, replaced it and finally worked well.
@staasguujaaw6651 Жыл бұрын
.015?
@serverman3285 жыл бұрын
You mentioned that you had a previous engine bored out .050 at a machine shop. How much did they charge you for that?
@zippyzappyz5 жыл бұрын
Andrew I was charged locally $100 flat, I bought the piston and rings separately on ebay though
@aderahman96734 жыл бұрын
If you can please made how to check injection pump yanmar l70 in good condition or thats broke
@zippyzappyz4 жыл бұрын
If you remove the injection pump, push on the spring to see how much tension it has, if it’s too loose, it’s broken
@passwordswordfish30135 жыл бұрын
Hy its possible to install the yanmar single cylinder engines horicontal not vertical? Thanks!!!
@zippyzappyz4 жыл бұрын
Amrudin Krdalic not without lots of modifications. I wouldn’t personally know how to do that myself
@ryadhnasr77414 жыл бұрын
Et son réglage soupape s'il te plaît ?
@raulalcocer92553 жыл бұрын
Buen día como puedo escucharlo en español
@gaviningalls98493 жыл бұрын
Hey can I get in contact with you man? I got a 7hp motor that is hard at starting takes over a min or more to start some times it doesn’t I have replaced the fuel pump and injector no improvements. Anything helps
@zippyzappyz3 жыл бұрын
Do you prime the fuel lines before hand? do you have a clean air filter and fuel filter?
@gaviningalls98493 жыл бұрын
@@zippyzappyz I have bleed the fuel lines a couple times now nothing changed. Also I can run a filter or no filter doesn’t change anything lol. Could I get your Facebook or number? To communicate better I can send you videos of what it is doing.
@gaviningalls98493 жыл бұрын
@@zippyzappyz I have bleed the fuel lines a couple times now nothing changed. Also I can run a filter or no filter doesn’t change anything lol. Could I get your Facebook or number? To communicate better I can send you videos of what it is doing.
@guypatts4943 жыл бұрын
Where can I get the shims for the injection pump at
@christopherherring17332 жыл бұрын
If you get a gasket set like from eBay it should come with injector pump shims.
@juancarloromero68302 жыл бұрын
How to remove the flywheel???any help
@vanmanuk Жыл бұрын
Screw a 8 mm spanner to engine body lock it up
@Mr._Fixit3 жыл бұрын
I have a Yanmar generator with L70AE engine. Looking for a good online source for engine and generator head parts. Having trouble finding reference material for generator. Found manual on engine only. Do you have an online source or do you have a local dealer?
@Maria-xm7gh4 жыл бұрын
Does it work for kipor?
@zippyzappyz3 жыл бұрын
yes!
@cinthiarosado26494 жыл бұрын
Por favor soy de ecuador me urge conseguir la contra pesa de una bomba a diesel alguien puede ayudarme