Just a tip, when testing if paint is tacky or ready for the next coat, don't touch the surface you are painting, touch the masking. That way you don't introduce oils from your finger in the paintjob.

If used as follows , these cans can have amazing results… all has to do with a little sanding. 2 coats of primer.. light sand in between coats with 1800 grit. 3 coats of the paint.. light sand again between coats. 2200 grit 2 coats of clear with a wet sand in between coats. I’ve had great results doing this way... takes a bit longer but well worth the patience. Did a 1996 Tacoma just full of fibreglass and bondo about 7 years ago now… still looks great . 😎 Wish they had grey though .

Works pretty good. Closest thing to a real air gun you can get in a spray can. Maintaining correct distance while spraying is very important, with minimal overlap or it tends to run. Creates tons of overspray, so it's much less mess if the painting is done outdoors.

Great video. I just painted my '81 F150 with a 6-pak of turbo spray cans. Took about an hour, it paints so fast. Turned out way better than I thought it would. Cost $87 for the 6-pak on Amazon.

I wish they had more colors outside of Black and White. I hope they come out with more colors down the road. I plan on doing another Rustoleum paint job

Great job. A couple of tips, (you may have done this), put hot water in a sink and sit the can in the water until the water is tepid. This will help atomize the paint spray better. Also did you do anything to the inside the fender, maybe a couple of light coats.

That’s insane how big of a fan that thing puts out!! Definitely turned out pretty good!

I am seeing alot of people singing the praises of these Turbo cans and painting cars with it, but, honestly, for the price of a can of it, I’d just break out the compressor and gun … or even an airless electric gun … thin some canned oil based paint, and add some hardner. You’d end up with a MUCH more durable paint job that will outlast spray can paint for about the same cost (maybe less if you already had some of the tools and materials on hand). I painted my mailbox and post with a spray can and it only lasted about a year before the paint failed. I repainted it with Rustoleum in a can and a brush (no hardener) and it still looks good 4 years on. I am sure, if prepped well, the Turbo can will lay out a nice finish. I’m just not sure it will last or be durable in the long haul. I guess it’s all about what your needs are?

when painting a light color such as white, it's better to put a coat of gray or white primer down, the black will bleed through worse than the gray or white will

This is a great video but I wish somebody would truly finish the paint job including wet sanding if needed buffing if needed polishing if needed because this paint seems like it has a lot of potential, especially when you consider the alternative having to take it to Maaco or pay $2,000 for a job that you could do yourself.

Have you thought about going over it with a 2k clear coat?

never have i thought while spray painting, " THIIS COULD BE FASTER!" lmao...

Bro had to run across the fender to prevent runs. I love it 😂

I appreciate the review and I'm not a professional, but omg the manner in which you paint was so difficult to watch. When you touched the paint I almost lost it 🤣.

Damn maybe 4 cans will do whole car lol😊

Thanks for the vid. Yea, these turbo cans are NUTS

Got some good tips here! I’m about to paint a bathtub in gloss white Oleum turbo cost me $35 Bunnings in Oz

Does better if you soak the can in hot water for about 20 min.

Rustoleum will hold up fine as car paint. If someone takes some kind of care of the car. I've put rustoleum through the worst and it's still there. I dumped out a bunch on my street and cars have been running over it for 6 years. They've worn through the middle of course, but the sides where the tires don't really go are still there. That's after being in the elements with no shade for 6 years. So you can safely say that it will do well on a car. It just might not look as good as car paint would. But for many cars, it can still be a huge improvement.

Nice sharing friend 👍👍

Dude that looks really good...I started this video like, man is he going to post this if the paint came out trash???

just wish they would make the turbo cans in more colors

Heres the million dollar question: CAN U APPLY A NICE CLEAR/protective finish to that paint ????? Especially w/o. Causing cracking or spider webbing .

This is actually pretty cool

Gosto muito de pintura com esprei

Thanks, didn’t know they made jumbo sized spray cans!

If only they came in different colors I need yellow lol

Why does my metallic rustoliam spray leave a small tiny air bubble? Am I spraying from too close?

Aaaaand nooo lungs!🤣🤣🤣

Wow that’s impressive I must say!

Perfect vid. for what iam doing, thanks.

Nice job. I wonder can this turbo can in white be used as a primer? I want to paint my car the oem red color but wonder if I can use white as a primer layer

Maybe paint the letter box or the beer fridge with it but that's as far as I would go.

Our boddy Gina have to wash his door

How long you have to wait before you do any biffing /compound polishing. I am rung rust oleum but i have tried buffing after 3-4 days and it just comes off with buffing even with the smoothest foam.

Do they have the clear coat in turbo cans

Quick and awesome ! 😎

Wow that'd almost too much pressure

Cool vid! Do you need to clear coat?

Can you send me me a few cans can't get any here in the uk.

Your time between coats is all wrong and it is best to bake the paint especially when you have a garage like that to work with. Either use a propane heater or just space heaters and circulate the air with a box fan but don't blow dust around. I like to paint at 85 degrees and wait until the maximum time is up for recoat on each spray but remember to take off your tip and clean it in mineral spirits very well and then make sure it is clean and ready to spray on a test board before second coat. Also soak the paint can in a 85 degree bucket of water to get it at the perfect spraying temp. Careful because your paint will be dry very quickly like this and you can make it dry in the air if you try to increase these temps any further so don't. I have experienced and most enamels I used like Rust-Oleum and krylon and DuPont and the auto parts store paint , I forget the name of the auto paint company but it is the exact same way. AC Delco? No that's not it. Duplicolor, that's it. Lol Yeah that one too will dry too quick if you spray any higher that 85 degrees and stand further back than 9 to 12 inches. I would stay at 10 inches at all times with a nice enamel and keep the room at 85 degrees and paint can in an 85 degree bucket of water when you use it. The drying time is different than recoat time technically and just because your paint is dry to the touch doesn't mean you can spray again always. Read the label.. some paint gasses off for 6 hours, some 12, lots 16 to 18 hours, most say 24 hours to be safe, but these conditions I am telling you with very little humidity and 85 degrees in the garage will gas out that paint faster and you should be able to split that gas off time into a out 60 percent safely but I would definitely test it because I have tried some that will be good to go in an hour, some that will spiderweb in an hour, and then some that will spider web up to 24 and 72 hours even but not in this climate I speak of. At 85 degrees and ultra low humidity many if not all oil paints will finish gassing off within 12 hours tops but they will tell you a lot more to be safe. It is sometimes a crap shoot weather or not to recoat instantly or waiting 24 hours. Many paints will say shoot it again within an hour or wait 24 hours which I would say is standard but I have luck with spraying Rust-Oleum back to back to back and waiting 9 minutes in between coats at 85 degrees then applying a urethane poly after 13 minutes and I am good for one piss coat then a 9 minute quick dry then one medium heavy coat, then wait 9 minutes then a final medium to medium heavy coat that I cal the closer and it is all good then. Lol Otherwise I spray with spraymax 2 k clear and I paint my piss coat, let dry 9 minutes, spray a medium heavy coat of color again then let dry 12 minutes, then one final medium coat to medium heavy coat foe my final and tuen i wait for that to flash and spray my clear right then in one fair swoop and it usually does the job. It dries super fast and I don't get fusion pop or fish eyes or orange peel or spider webbing if I follow these directions. The thing I run into is when to recoat though. Some of these times are different for certain products. Some want you to spray your clear coat after 12 hours or after 30 minutes but nothing in between. Some tell you nothing at all until it has gasses off completely for it full 24 hours or maybe 72 hours which is a bad product in my opinion but they exist. The best is duplicolor and spraymax in my opinion and I always do the 13, 9, 9 method then spray my clear after it has gasses out at 12 to 24 in an 85 degree low humidity garage. It's tough to judge now days because even the paint varies with recoat times from can to can as much as 50 percent I have found. It's hard to really nail down a recoat time especially when switching from brand to brand and enamel to poly and urethane to laqeur and so on. It is a hard one to judge so you are better off buying a can extra of your paint and testing it in the exact environment with a similar piece of metal or whatever you are painting to see what is flashing at what times in what way and when recoat is acceptable and when it starts fighting with the last coat if at all and see for yourself so you know your limitations and you can learn what you like, how you like it, how much you like it, how long you like it for, and then you will know why you like it and at that point you are as confused as I am and a full blown addict of painting things. 😅😅😅😅 Remember it is always easier to put more on than take it off but that doesnt necessarily mean that putting on just a little will prevent you from having to take it off. Some of the biggest screw ups we make are not runs from too thick a paint job in one area only but it is when we paint at the wrong time and we get spider webbing, crocidiling, snowflaking, cracking, mudding, splintering, splitting, orange peeling, dimpling, bubbling, blistering, glazing, pitting, hazing, popping, milking, streaking, peeling, flaking, running, thinning, frizzing, gumming, and full on lack of adherence I call sheeting which is rare and only happens when I lube up my paint project with KY Jelly accidentally before I spray or try to paint something water based on an oil based paint that is completely dry first and foremost and then still ends up drying in a full piece on top and can be peeled off in that said one piece easily because of no adherence whatsoever. . So now guessing and practice first and get your temps right and times right. You will be happier and then you can just bitch about the paint never being the same instead of your methods and application process in full order. Damn paint companies change up their formulas and ratios more than a girl changes nail colors. Did I mention

How'd it hold up

I like how you made a video about painting a car but only showed five seconds worth of finished product

With this it looks like I won't be needing my air compressor anymore😢. Should I buy this turbo cans to paint a couple metal cabinets and my bathroom vanity piece or should I just use the small compressor I have with my critter spray gun?? It looks much easier to paint with the turbo cans

Did you say you were on your 4th coat? How many cans do you need to do a whole car?

Did you do any sanding afterwards

Where can you find the turbo cans ? How many colors do turbo cans come in ?

Have fun getting the over spray off your windows, that is slow drying straight enamel you gotta cover up anything you dont want paint on.

Awesome 🤩 👍👍👍👍👍👍👍

That turbo can of paint will do much more than one finder! Almost a waste to use it on only a fender, with smaller cans up too task? That can could almost do that whole small car.

I think they suck. My 2 cans both sprayed a stream from the top of the fan shaped nozzle and also a steam from the bottom of the fan shaped nozzle…but zero stream from the center of the fan shaped nozzle. Back to the drawing board?

I wonder if I can use this paint on my boat

Does the pressure stay the same until tha can empty’s?

Whole 3 sec final outcoma.

Does it have a finishing clear coat?

Where'd you go again? Hopefully you're alright!

Nice. Think I could do a whole 2007 honda accord? If so how many cans ? Thank you

Exact time between coats???

The problem is the Turbo Can colors are only black and white (-and maybe clear).

Do they have blue

nice but these spray cans dont have a hardener and sun guard in it...your paint will look like crap after time......you get what u pay for bro

What happened to the other videos Russ?

Wish it came in more colors

Pintei meu carro todo nos esprei

Just because a can has a wide fan doesn't mean the paint is any good I would not think about painting anything worth anything with it doesn't have hardner .

Where’d you get this? Can’t find it anywhere

Hi medic magic, did you sand down the area before painting and use Primer ? Or was it just taping off the area and spray painting over the flat black panel? I’m hoping it was just painting. Please let us know

drop the link where you can order it

You have an E30

Onde compro ??????

A can is almost $16 now

Only good from 20 feet away or more

There is a reason why professionals mix paint. You get what you pay for.

You shouldn't start or finish a pass directly over the surface, you are inviting problems.

Tem um saco de ração cheio de esprei vazio

Jesus is LORD. ⚠You have been informed.

He is way to close with that turbo fan spray. He could almost double his distance. I am surprised there are no runs. Way to many coats. That is why he has orange peel.

Wow, no idea how to use a spray can.

Word of advice throw a sheet of plastic over the rest of the car even though you mask off the fender you don't want overspray landing all over your glass your trim and all that cuz it's a mother to get off overspray

I am done with this company. Their spray cans stop working if you don't use them all at 1 time.

Dude, I don't mean to roast you, but for your own sake, watch some KZfaq videos on painting before making a KZfaq video on painting.

Dude, wtf it would have been easier to spray paint the fender off the car, and you should never ever spray paint anything again like never ever again 😑

First

Twelve dollars? WOW It looks more like a twenty dollar paint job.

Don’t touch it goddamnit

Naaah dude , don’t be like these idiots on KZfaq using the wrong kind of paint for cars

Too bad they don't come in metallic red or blue it only comes in two ugly boring colors black and white

More interested in orange peel

Nice don't match though

1 part paints have inferior durability.

This is actually pretty cool

First