I feel the same way about my 5.56 reloads. 55 grain Everglade version 2 bullet on top of 24.5 grains of shooters world ar plus powder. I get .90 inch groups at a 100 yards out of my psa rifle with a 18 inch barrel

@@theintrovertedcalifornian5047 yes sir Im using benchmark myself 25.2 grains nets me half or under…. As long as there is nothing wrong with the barrel any of them will shoot with proper ladder testing of loads, its all resonance at that point and getting the round to leave the barrel cleanly at the crown. Great work man under a inch is 🤌🏻

Only experienced reloaders appreciate this, tuning the load for it's intended weapon. Theres several variables to play with

@@schinderiapraemeturus6239 absolutely! I have many hours of the “thrill of the hunt” and notebooks loaded with info to get where Im at currently. I have custom barrels to mass production barrels and all my stuff is on it 🤘🏻

Interesting, i bought a cmmg 22lr conversion kit and haven't had a chance to see how it compares

I shoot black powder guns, mostly Flintlock though I do have some percussion guns In my experience is that blackpowder is usually harder to find then most cartridges are. I know about making black powder but it’s usually about buying the components and mixing it…Not really a solution I don’t think

@@deadhorse1391 I understand. This being my hobby, I find it cheaper and easier to compile all the components for black powder guns easier than one might think. One weekend can yield two pounds of powder, and I can cast a couple of thousand rounds during that time. The caps are homemade as well, using the proper ingredients and a cap maker. But, results may vary and you have to want to do it.

@@noapologizes2018 do you buy all the components to make the blackpowder or do you also process the salt petter, sulfur and charcoal ?

@@deadhorse1391 I know how to process saltpeter and charcoal, but the sulfur I buy and have a lot. The potassium Nitrate I have purchase as well, but still can make my own if need be. The sulfur is a whole different animal. I have no natural resources, so I have to purchased enough to serve me. Of course, everything runs out, but I can make enough to last awhile if TSHTF.

Tis played on a blues scale with tripples, which is why it sounds a bit off

@theblindsniper9130 lol. I know. I've been a musician of multiple instruments for 30 years. You have a good channel and I am subscribed. I do have to give a bit of shit. I do stand by loading my own, however. It is way cheaper and more accurate. My question is how do we get 1,000 round cases of 7.62x39 with the Biden administration infringing on our 2nd Amendment.

kzfaq.infock2H-aF1EE8?feature=share

Good idea posting that on the internet lol

@@justacentrist4147 why? should I stockpile more?

@@noneyabiz8225 no you probably shouldn't tell the world and your government you have that much ammo stored away. If something did happen (not that I think it will I'm not a prepper) your government is definitely going to be coming for that. Better to shut up than brag

@@noneyabiz8225 you just announced to the world and your government that you have that much stoked not smart better to be quiet than to brag.

BRAG? i got 1 billion rounds. Id be more worried about someone burning down house out of jealousy or a crazy liberal.​@justacentrist4147

I'm a reloader as well. 35 years. Primers are hard to come by and damn expensive not to mention a lot of powders are gone. I"ve been yelling at people for the last 4 years to stop dumping ammo like its 1990.

You don’t need small base dies

@@theintrovertedcalifornian5047 ive loaded for multiple ARs...never used small base. Always thought that was a chamber problem or bad sizing methods.

@@theintrovertedcalifornian5047 Do you need them? No but if reliability has been an issue in the past and you want to load for any chamber of any gun & with any thought of use in SHTF or whatever it cheap insurance. Yes brass life will suffer & you won’t get the the peak of accuracy that comes from loading for one gun only.

And for those that say you don't need small base dies probably haven't been reloading that long and are ignorant to the fact that small base dies are made for a reason you can tell when your starting to have a problem with your brass by using a go no go gage your brass will start to get fat at the base and won't quite go all the way in the gage but will still chamber in your gun that is tell you it's time to run your brass through a small base die in my opinion it seems to happen more often with 223.

Tim your old ass needs to train too. Don’t neglect the training and physical fitness aspect of it.

In the heat like 90°+ it doesn't shrink as well as brass after being fired and can cause a fte, the worst kind of failure as you need a ram rod to get it out, has happened to me enough times id never depend on the stuff

On each rifle it's happened on, they were all very high quality firearms

(Shrugs) The writing is on the wall. Some people actually believed the []--[]]]]]]]]]]]>--- was safe/effective

I'd be upset as well with a name like reuben lmfao

I'm not sure who that is but search those words and found nothing, you have any links for sources ?

@@Soli_Deo_Gloria_. Sam is the owner of SG Ammo. He's got fair pricing and great shipping. Never had an issue with SG orders. I do find cheaper prices sometimes, but order from him at least a couple times a year. They are based in Oklahoma outside Stillwater, I Believe. Subscribe to his newsletter. He gives out inside information at the top of the email.

@@Soli_Deo_Gloria_. Look up sgammo

Oh OK thanks... Yeah their prices are generally meh... I remember a few years ago Mishaco called it SGScamo... lol I wonder if that price increase is his company alone or if it is reflective of manufacture, because CCI is good at headsup newsletters for price increases... and haven't heard of any as of late... My Walmart recently increased the prices because of the last CCI 1-7% increase several months back... While most things increased the 525 bulk pack of Remington golden bullets went down from 42 to 37 bucks... Which was strange... 🤷‍♂️ Thanks again for responding n' God bless brother

@@Soli_Deo_Gloria_. Newsletter states it is the Kinetic group (includes CCI) will increase handgun load pricing May 1. Mag tech and S&B says they will follow suit. PPU announced the 6-7% increase will come in June. Scam or not he gives valuable information.