@dathat3204 3 ай бұрын
What a surprise, I have a weak spot for vibes and always pick up any jazz albums with vibes on them when I'm out digging. So nice to see the inner workings of a vibraphone, thanks!
@analogemma 3 ай бұрын
I'm glad you enjoyed!!
@nicole_local 3 ай бұрын
Beautiful instrument! Nice repair job
@analogemma 3 ай бұрын
Thank you!!
@squantosr.583 3 ай бұрын
Between this and your lapsteels you could make quite the hawaiian album 🏝️
@analogemma 3 ай бұрын
LOL, I don't have any lapsteels though 😋
@kunaikai 3 ай бұрын
Great work as always. I love anything vibe or fender Rhodes. that bell tone is so nice
@analogemma 3 ай бұрын
Thank you so much!! My dad said it was a giant rhodes lol
@jussikuusela7345 3 ай бұрын
You will not get an appreciable speed increase by overvoltaging an induction motor. The listed speed is usually the nominal speed, a "tad bit" lower than the synchronous speed, which is 3600 divided by a small whole number (3000 respectively divided for 50Hz countries). Without increasing the frequency of the power supply to the motor, or having an external source of power to spin the shaft faster, you can't exceed or even reach the synchronous speed. The former case could be achieved by a VSD. In the latter case, the motor would act like a generator and backfeed power to the network once synchronous speed is exceeded. The "vibra" part is a misnomer because it is not a vibrato effect, but between a tremolo and LFO controlled resonance. But it sounds nice!
@analogemma 3 ай бұрын
Yes
@surrealism33 3 ай бұрын
home run, nice work!
@analogemma 3 ай бұрын
Thank you!!
@MrCoyoteculler 3 ай бұрын
Cool project! We'll done. Kroil and flitz are both top notch products. Semichrome polish is also as good if not better than flitz.
@analogemma 3 ай бұрын
Agreed! Thank you!
@StevenCalwas 3 ай бұрын
That's really cool. Congratulations on persevering and not letting the motor issues defeat you. I didn't even know a vibraphone had a motor. The instrument sounds great, too. Is it a keeper or will you sell it?
@analogemma 3 ай бұрын
Thank you! I think I'm going to make some more videos with it hopefully and then see what to do with it. Not the smallest instrument lol
@dapatrick 2 ай бұрын
Thank you for this! Do you mind sharing where you purchased your replacement belt?
@analogemma 2 ай бұрын
No problem, I got it off Ebay. I looked up "Jenco Vibraphone Belt"
@dapatrick 2 ай бұрын
@@analogemma Thank you again! Looks like there are no current listings. Do you mind sharing the approximate circumference of the belt you bought?
@stevenwendt7927 2 ай бұрын
I have a jenco vibraphone but no motor. Can you tell me the specs of the motor that it came with??
@analogemma 2 ай бұрын
Hi Steven, it was a Bodine Electric Company Model NSP-11R speed reducer motor. 1600 RPM, 115AC. Important: 2.7 Torque, the model will read the same but the torque values change
@stevenwendt7927 2 ай бұрын
Okay! And do you know the final RPM after the speed reduction?
@soultrane9074 26 күн бұрын
@@analogemma Hi Emma, how can you figure out the torque on these models? most of them dont have it written. And also, does a 208/240 V makes a difference. I'd really appreciate any guidance you would have into understanding these specs with old motors (especially if you have some recommended literature) Im a fan of your work. Thank you!
奧特羅羅 Ultraman
Рет қаралды 6 МЛН
ThePianoforever
Рет қаралды 896 М.
WIRED
Рет қаралды 1,6 МЛН