Re-Blue an entire barrel with Super Blue Remington 1100 project part 1

Рет қаралды 220,642

3 жыл бұрын

Part one of the Remington 1100 project. Re-blue the entire barrel using Birchwood-Casey Super blue. An economical, user friendly process of bluing.
If this video helped you, or saved you money, please consider donating a small amount to our Paypay, Channel fund link listed below.
Perma Blue How To video (same process) • Cold blue with Perma Blue
Remington 1100 project:
Part1: Re-Blue the entire barrel
• Re-Blue an entire barr...
Part2: Carlsons 8 shot magazine extension
• Carlsons 8 shot extens...
Part3: Brownells Aluma-Hyde receiver
• Brownells Aluma Hyde R...
Part 4: Sure Cycle Action Spring
• Sure Cycle Action Spri...
Part 5: Boyds Stock set
• BOYDS Stock Remington ...
At the range with the Rem 1100 Project!
• Remington 1100 project...
Want to help our channel? Buy great stuff from these businesses who support our channel and help keep us going!!
V V V V V V V V V V V V V V V V V V V V V V V V V
Paypal Support Funds : Throw us a couple bucks to help buy stuff for the channel
paypal.me/ZRUS
Affiliate Links:
Gunadapters:
www.gunadapters.com/
Code "ZRUS" for 10% off your purchase
Major Sponsor of our channel!
-----------------------------------------------------------------------------------------------------------
OpticsPlanet: bit.ly/2eUd4Cm
5% off your entire purchase with coupon code "ZRUS" at optics planet.
-----------------------------------------------------------------------------------------------------
LA Police Gear:
la-police-gear.pxf.io/c/26694...
------------------------------------------------------------------------------------------------------
Matthews Fabrication adjustable cheek rests:
matthewsfabrication.com/
Use coupon code ZRUS10 for 10% off your purchase!
----------------------------------------------------------------------------------------------------------
Like our facebook page for updates and future content !!
/ zombiesruspage
Follow us on Instagram!
/ zrusoutdoors

Пікірлер: 176

@Runflatred 2 жыл бұрын

I used this on my Remington 870 Express. I did the whole shotgun not just the barrel. Just be careful not to get it on the wood. Before I blued it I used the blue and rust remover made by the same company. Worked great. I didn’t use steel wool between coats. I just did what the directions said. After 7 coats the gun looked like it just came from the factory. It’s 35 years old and had a lot of rust on it when it was given to me. After I finished working on it the guy who gave it to me wanted it back. Sure OK. Not on your life. BTW. The whole gun only took me five hours and that included refinishing the wood with linseed oil. Wish I could post pictures.

@KHANPHOTO1

Steel wool didn't help. You degreased the gun of all oils and every time you put steel wool on the barrel you brought it back. Steel wool is treated with oil/anti rust to stop the hair like steel from rusting away while its sitting in the bag on your shelf. If you have to use steel wool, soak it in degreaser before using it and contaminating your barrel. It probably contributed to the splotchy look. Great topic and showing the work involved.

@jerryg2073

You should not be touching the barrel with a bare hand. Even skin oil will cause problems.

@blrenx Жыл бұрын

Ya did it all wrong.. You were treating it like paint... it's not, It activates then applied to steel. You can't speed up the drying. Bot what I don't understand is why you finished after you did all the hard work? If you kept adding blue and steel wool .. It would look perfect

@ronaldgreen3751 2 жыл бұрын

I have use the super blue in the past and I found that it takes at least 10 coats to get a good finish. In between coats I don’t use water i use 90% alcohol to clean it and then steel wool and then clean it again and then apply the bluing. I do use a hair dryer to keep the Metal warm if you keep it hot seems to work a lot better not super hot just very warm to the touch. I have one barrel that’s over 20 years now and still going strong.

@carlschnier4089

Wear gloves on both hands to avoid oil contamination and fingerprints

@liggerstuxin1

I’ve seen the comments of people saying that you should have used more steel wool and more blue. Either way I think it looks great.

@timnavarrette3274 Жыл бұрын

Why is he not wearing gloves???

@sicsempertyrannis3251 3 жыл бұрын

I always pour blue in separate cup if you wish to use what is left on another gun because you can contaminate whole bottle soaking the cotton balls with the bottle itself

@BloodnGutz43 2 жыл бұрын

Hey Dude, wear a pair of gloves you keep touching the barrel or top rib, mag tube ring with bare hand ? , i re blued my air gun barrel, with perma blue great finish didnt take very long but no finger prints on it any where< as used pair of pvc gloves

@thomaslandi6698 Жыл бұрын

Thank you for your video. I followed the procedure and the barrel came out better than expected.

@eidtnaci Жыл бұрын

Great installation videos I’ll definitely use this process on a single shot shotgun pre-1920’s

@robertlopatto338 2 жыл бұрын

Great job. Clear message, easy to understand and very well spoken. Pleasure to watch!

@TheManFromMA 2 жыл бұрын

Doing a restoration on a Remington 700, this video will help, thanks very informative

@bearly1727 3 жыл бұрын

I have done this many times and every time it turned out very well, not perfect, but very presentable. Different steels, different results, on same weapon. I've never preheated so I might try that on my next project.