Thanks for all the tips. You know, a small table or portable work surface would be useful so you don't end up dragging grit off the floor into that lovely motor of yours.
@DRKKNTRACING3 жыл бұрын
Yea but I like the realism lol
@DarkSim773 жыл бұрын
If you drop something in the oil pan, before dropping the oil pan etc try and see if you can get a magnet in there to fish it out ...some parts aren't magnetic but I've found over the years that a lot of them are. Could possibly save a lot of work/hassle..
@danielpotter89572 жыл бұрын
Looking at getting this done. Bought the plate, not convinced many shops know why this needs doing and therefore won't have done any.
@carlgar2007 Жыл бұрын
WOW this so wrong and bad in so many ways. this dude is putting all the parts on the driveway. How about a small bench and keep all your ENGINE PARTS clean?
@daddydaughterfun80749 ай бұрын
Thank you for this video you are awesome.
@MrShiestyAmg6 ай бұрын
Trying to get the gear in lined but it’s not turning to respring the second clutch basket gears
@pitbikecookracing33243 жыл бұрын
👍🤠
@DarkSim773 жыл бұрын
What year ZX14? Gen1 or Gen2?
@DRKKNTRACING3 жыл бұрын
Gen 1
@Zx14rrrrrrrrrrr3 жыл бұрын
Bro. I finally got around to doing this and I dropped the damn pin. Stuck a magnet all in there. Nothing.. Now I gotta drop the damn pan. 🤦♂️
@DRKKNTRACING3 жыл бұрын
That's sucks but gives you a chance to pull the pickup and clean it.
@Zx14rrrrrrrrrrr3 жыл бұрын
@@DRKKNTRACING pick up goes on the pan? Or at the bottom of the motor?
@DRKKNTRACING3 жыл бұрын
@@Zx14rrrrrrrrrrr its in the pan
@Zx14rrrrrrrrrrr3 жыл бұрын
@@DRKKNTRACING OK thanks.
@deliciousgixxer367010 ай бұрын
Is this needed for the gen 2 engines?
@KonradKondras-ul9nf2 ай бұрын
all from 2006 to 2024, I have a 2021 zx14 and I will also make modifications
@Zx14rrrrrrrrrrr3 жыл бұрын
2:25 can you explain a little.. What it is you're doing here exactly..
@DRKKNTRACING3 жыл бұрын
The inner sleeve is what aligns the clutch basket up and keeps everything sound. The basket cannot just pull straight out because it’ll hit the case and won’t come out. The basket gear has spring tension on half of it and If you pull the clutch basket out and don’t remove the sleeve first then you will struggle trying to push the basket back on to remove the sleeve. Basically the sleeve allows the movement to gain clearance to remove the basket.
@Zx14rrrrrrrrrrr3 жыл бұрын
@@DRKKNTRACING OK. Got ya on that part.. But as far as the magnet? You were just trying to pull it out a bit to get a grip on it?
@DRKKNTRACING3 жыл бұрын
@@Zx14rrrrrrrrrrr yea if you get it out far enough then you can grab it and pull it out
@Zx14rrrrrrrrrrr3 жыл бұрын
@@DRKKNTRACING gotcha.. Just looked like you could grab it before the magnet. That's why I asked. But I get it now..
@sonnybass9376 Жыл бұрын
So you prefer the sae brand over ape? Or with just a cover it doesn’t matter?
@Zx14rrrrrrrrrrr3 жыл бұрын
Why not the oil pump gear?
@DRKKNTRACING3 жыл бұрын
With only having a cut oil pan you run risk of sucking the pan dry with oil gear, plate, and relief valve. Its fine if you have a flat pan.
@Zx14rrrrrrrrrrr3 жыл бұрын
@@DRKKNTRACING ah OK. And is the plate necessary for all years or was the problem corrected on the Gen 2? I hear different answers lol
@DRKKNTRACING3 жыл бұрын
Its recommend on both gens. I know the gen 2 had some oiling upgrades but not sure to what existent
@Zx14rrrrrrrrrrr3 жыл бұрын
@@DRKKNTRACING will you video the relief valve mod? I can't find anything on KZfaq. Just the plate..
@DRKKNTRACING3 жыл бұрын
@@Zx14rrrrrrrrrrr yes sir. In ordering it this Wednesday and should be making a video the following week.