14 күн бұрын
4 ай бұрын
7 ай бұрын
8 ай бұрын
Пікірлер
@seimela 2 күн бұрын
this video is good you must English version
@seimela 2 күн бұрын
do more content on fanuc
@recopakistan1520 2 күн бұрын
I will try my best
@loveapple3135 3 күн бұрын
جناب اس کے ساتھ کونسی موٹر سہی رہے گی خراد مشین پر چوڑی ڈالنے کے لیے Absolute Or incremental
@recopakistan1520 3 күн бұрын
Both are suitable But in this video controller is incremental
@loveapple3135 3 күн бұрын
@@recopakistan1520 بہت شکریہ جناب
@AmjadTech 3 күн бұрын
Can you explain in details, How to sync routry encoder with Z axis for Threading on lathe
@recopakistan1520 9 күн бұрын
please like and comment for full video with complete wiring diagram with example. thanks
@recopakistan1520 10 күн бұрын
Which machine design you like the most please tell me
@ranashahbazali6456 11 күн бұрын
Good raheel sb
@recopakistan1520 11 күн бұрын
Thank you bhai jaan
@chauhan123jagdish 12 күн бұрын
Mere me x,c,z,sabka alarm baj raha hey muje machine chalu karne ke liye bar bar machine ko band karke chalu karna padta hey tab Jake home position aati tab tak oprate nahi hota machine home position ka setting kese kare
@recopakistan1520 12 күн бұрын
CNC Home without Limit switch in 990TDc-2 Controller kzfaq.info/get/bejne/eNN1Zd2Xspmmf3k.html Watch this link to solve your issue
@ytfan3815 13 күн бұрын
Hello sir, is it actually possible in a Fanuc control to do the motion in program-run with MPG ? On my 21i-MB I can Feed Hold on G84 tapping ( PAR 5200 ), also can switch to HANDLE and overtake the rotating Z +/- by the MPG, it's synchronized to the spindle. Do you need settings/parameters to do what you'r showing at 4:40, we have also a machine with 0i-MF controller. Thank you in advance.
@recopakistan1520 13 күн бұрын
I haven’t seen this feature in Fanuc I tried but never found this feature in Fanuc
@ytfan3815 13 күн бұрын
@@recopakistan1520 Okay thank you sir for the reply. I thought your FEELER had a Fanuc control, is a bit difficult to see and I don't speak your language so maybe you mentioned it and I missed it. 😉 Regards.
@ahsannimra139 14 күн бұрын
Sir cnclathe threading programing ki video bna dy
@recopakistan1520 14 күн бұрын
video will come soon InshaAllah
@seimela 14 күн бұрын
YOU HAVE NICE STUDIO MY FREIND
@recopakistan1520 14 күн бұрын
Thanks my friend
@recopakistan1520 14 күн бұрын
my studio is nice and and content is also nice ?
@seimela 14 күн бұрын
@@recopakistan1520 it's all good man
@recopakistan1520 14 күн бұрын
@@seimela thanks a lot once again my friend
@FabioScovoli 19 күн бұрын
Good morning. I need help, I installed the XCMCU - XC609T command. And I can't thread a screw into it. Z axis motor pulley 18 teeth. Driven pulley 36. My spindle pitch is 10mm X axis motor pulley 18 teeth. Driven pulley 36. My spindle pitch is 5mm Encoder with 3 channels A+, A- B+,B+ Z+,Z- Gnd 5v I'm using Easy Servo 12nm. Driver 2LS860H However, every time I start the alarm 58 cycle The threaded thread is too large for the shaft. Could you help me with the parameters? Thank you very much in advance
@recopakistan1520 18 күн бұрын
Yes I can help you Can you please send me your video My what’s app no. written in description
@Amritpalsingh-rd8dt 21 күн бұрын
❤ from Punjab
@recopakistan1520 21 күн бұрын
Thanks bro.
@Mughalbrand3 25 күн бұрын
Amazing video Bhai ❤❤
@recopakistan1520 25 күн бұрын
Thanks
@recopakistan1520 25 күн бұрын
Thanks
@MohamedahmedDiab-kn9wh 25 күн бұрын
Fantastic
@recopakistan1520 25 күн бұрын
Thanks for appreciation I really need it
@Mughalbrand3 27 күн бұрын
Sir 990 control pr alpha spindle drive chal sakti ha
@recopakistan1520 27 күн бұрын
Every analog spindle drive will work with 990 controller
@MohamedahmedDiab-kn9wh Ай бұрын
Fantastic Please can you make video for simulate programme
@recopakistan1520 Ай бұрын
kzfaq.info/get/bejne/hL-nns6X2Nq5YGg.htmlsi=kbVq_cblDwT25xvo Watch this link from 1:05
@MohamedahmedDiab-kn9wh Ай бұрын
@@recopakistan1520 thanks sir but this video contains display colours and language and graphic but I need simulation for programme and thanks again.
@recopakistan1520 Ай бұрын
@MohamedahmedDiab-kn9wh soon I will upload a video at this topic simulation
@MohamedahmedDiab-kn9wh Ай бұрын
@@recopakistan1520 thank you
@kingzeeshu2199 Ай бұрын
Thank you sir ❤❤
@recopakistan1520 Ай бұрын
You are most welcome
@Amritpalsingh-rd8dt Ай бұрын
Love from Punjab - india..❤❤
@recopakistan1520 Ай бұрын
Thanks
@MohamedahmedDiab-kn9wh Ай бұрын
Please how to nake simulation in newker control
@recopakistan1520 Ай бұрын
You can watch my 990 course videos
@kushalanantraut5013 Ай бұрын
part count kai se kare
@recopakistan1520 Ай бұрын
How to do part count Zero in 990TDc and 990MDc Controller watch this video
@recopakistan1520 Ай бұрын
How to do part count Zero in 990TDc and 990MDc Controller kzfaq.info/get/bejne/os1mhs-kv7axYoE.html
@marcio.roberto.torneiro4897 Ай бұрын
Este comando chines para 2eixos , para programar vc usa algum programa com CAM ?
@recopakistan1520 Ай бұрын
I can understand only English
@kingzeeshu2199 Ай бұрын
Please ak video date and time change Kesy krty hain ye b bana den shukriya❤
@recopakistan1520 Ай бұрын
Video will come soon insha Allah
@kingzeeshu2199 Ай бұрын
Thanks 👍
@kingzeeshu2199 Ай бұрын
@@recopakistan1520 kb tak video upload kro gy sir
@recopakistan1520 Ай бұрын
@kingzeeshu2199 video is ready to upload You will see at Monday
@kingzeeshu2199 Ай бұрын
@@recopakistan1520 thanks
@amjadali-id3ox Ай бұрын
V Good bro❤
@recopakistan1520 Ай бұрын
Thanks 🔥
@seimela Ай бұрын
Keep well❤
@recopakistan1520 Ай бұрын
@seimela thanks for support
@MrHarsha42 Ай бұрын
G0 ka speed by default 2000 hai.. kaise usko change kare?? Maximum kitne tak ka dal sakte hai ??
@recopakistan1520 Ай бұрын
Learn Retrofitting Parameters Tutorial CNC Controller 990TDc by Reco kzfaq.info/get/bejne/Zpx4o8-ft-DXaKc.html
@recopakistan1520 Ай бұрын
Watch this video for change G0 speed
@MrHarsha42 Ай бұрын
@@recopakistan1520 already saw the video.. max kitna rakh sakte hai g0 speed??
@MrHarsha42 Ай бұрын
@@recopakistan1520 Mera default hai 2000
@recopakistan1520 Ай бұрын
Jo parameter may enter kya hay itnay ho jay ga
@HashirButt-kw6rp Ай бұрын
Same milling control lathe per laga hai jo radius lgana hota hai wo nahi lagta same program dosri machines pr chal jata hai is control m radius to small ajata hai is k liye small chamfers lga kr kam krta hon help
@HashirButt-kw6rp Ай бұрын
Sir milling control laga hai swiss lathe per radius k liye small chamfers lgani parti hain any solution
@recopakistan1520 Ай бұрын
Use G18 code before start your program
@user-yr8lt4rl4x Ай бұрын
very good
@recopakistan1520 Ай бұрын
Thanks
@amjadali-gq1kv Ай бұрын
very nice👌👌👌
@recopakistan1520 Ай бұрын
Thanks
@marcio.roberto.torneiro4897 2 ай бұрын
Hello professor, congratulations on the videos, you explain well and I'm from Brazil, the capital of corruption hahaha. Regarding the cnc control manual for lathe in my case of the Newker 1000 series, is there any way you can make a video explaining the cycles? Even if you use the model 990 command, it would be interesting to show a drawing showing programming using cycles, it could be one cycle per video, depending on your free time, Newker's manual is very bad, especially for us in Brazil when translating the translation does not make sense . 
@recopakistan1520 2 ай бұрын
I will try my best to provide content as you want and thanks for appreciation
@tippojee1491 2 ай бұрын
Sir how to count zero in washing WA-31XT controller
@recopakistan1520 2 ай бұрын
We helps only for newker control
@tippojee1491 2 ай бұрын
@@recopakistan1520 Ok
@mafizurr 2 ай бұрын
Thanks for your hard work.Boss background music to much ...your voice to low ...want to hear you louder ...please
@recopakistan1520 2 ай бұрын
Please watch my new videos you will get what you want
@kamalovdenis6811 2 ай бұрын
После такого ремонта лучше он точно не стал ))
@recopakistan1520 Ай бұрын
purpose of this video is how to repair with minimum resources
@kamalovdenis6811 28 күн бұрын
@@recopakistan1520 Это не ремонт, ремонт подразумевает приведение характеристик устройства к исходному или близко к исходному состоянию за счет замены изношенных деталей, после замены деталей должна быть балансировка, регулировка натяга подшипников за счет изменения зазора приставка, (подшипники изнашиваются натяг уменьшается, ) то тот минимум который влияет на показатели точности и жёсткости шпинделя. В лучшем случае провели технический осмотр, даже техническое обслуживание лучше так не проводить. В целом если нечего точного на станке не делать то жить будет конечно. Удачи вам.
@HanySabra 2 ай бұрын
god bless you
@electestengineering7135 2 ай бұрын
Do you video for the ball screw pitch setting?, the z axis is not absolute , i mean the depth is not precise cost Z axis Ball screw different pitch to Y and X axis, i cant find the ball screw settings''
@recopakistan1520 2 ай бұрын
Video will come soon at this topic InshaAllah
@electestengineering7135 2 ай бұрын
Thats amazing! Thanks Bro
@stevegoode3769 2 ай бұрын
LOL Seen people do this sort of stuff and call it pro wow Stay away from mine
@recopakistan1520 Ай бұрын
the purpose of this video that how to repair with minimum resources
@EisaMughal-xr4fh 2 ай бұрын
Sir threading programing pa ik video bana da mokamal information da?
@recopakistan1520 2 ай бұрын
Video will come soon Insha Allah
@EisaMughal-xr4fh 2 ай бұрын
@@recopakistan1520 thank you ☺️
@gertkristensen6451 3 ай бұрын
so much backlash doesn't have to be compensated, then a new spindle has to be put on .. what are you thinking about
@hrmotivation-ko9qn 3 ай бұрын
ap isi panel pe or videos banain
@piyodefree1 3 ай бұрын
Thank for explanation sir, But i have problem with diameter x measure not suitable between actual and my nc programing. How to adjust them.
@recopakistan1520 3 ай бұрын
Types of tool offsets in 990TDc 2 lathe Controller kzfaq.info/get/bejne/qsibqM6bvpjTnmg.html
@recopakistan1520 3 ай бұрын
Please watch this video i hope your issue will be resolved Link is given in above comment
@marcio.roberto.torneiro4897 3 ай бұрын
Hello, can you make a video showing how to program the G76 threading cycle? How to fill in the variants and explain each one?,🇧🇷🇧🇷🇧🇷🇧🇷
@marcio.roberto.torneiro4897 3 ай бұрын
Hello, can you make a video showing how to program the G76 threading cycle? How to fill in the variants and explain each one?,🇧🇷🇧🇷🇧🇷🇧🇷
@recopakistan1520 3 ай бұрын
Video will come soon insha Allah
@marcio.roberto.torneiro4897 3 ай бұрын
@@recopakistan1520 I asked for a video because a friend installed a 1000 newker series control, but I didn't understand the thread cycles and here in Brazil, everyone I ask for help doesn't help. The cnc command printed the manual but when translating it is not possible to understand the translator translates meaningless words. 
@hrmotivation-ko9qn 3 ай бұрын
SIR DATA EXCHANGER KO KESY INSTALL KARAIN POWERMILL 2009 MAIN OR POWERMILL 2020 AIK DAFA INSTALL HO K KHATAM HO GYA HA OR DOBARA INSTALL NAHI HO RAHA MADAD KER DAIN
@Gabriel-mb1dr 3 ай бұрын
Do you have any contacts? I've never used this controller before and I may need consulting, I believe you have extensive experience in what I'm going to do
@Gabriel-mb1dr 3 ай бұрын
Which controller was used?
@recopakistan1520 3 ай бұрын
Model: Cw20T cnc lathe controller
@Gabriel-mb1dr 3 ай бұрын
@@recopakistan1520 Thanks for the reply, I really liked your content. I'm about to retrofit a center lathe do you think the xcmcu controllers will work too?
@recopakistan1520 3 ай бұрын
@Gabriel-mb1dr cw20T and xcmcu both are the same controller from different suppliers
@recopakistan1520 3 ай бұрын
@Gabriel-mb1dr and thanks for liking my content really need this appreciation
@Gabriel-mb1dr 3 ай бұрын
@@recopakistan1520 Do you have any contacts? I've never used this controller before and I may need consulting, I believe you have extensive experience in what I'm going to do
@crox2012 3 ай бұрын
I wish you could use English i do really
@recopakistan1520 3 ай бұрын
Some people said I should Urdu/Hindi some people says use English what should I do ?
@crox2012 3 ай бұрын
@@recopakistan1520 hhh thanks for your feedback
@crox2012 3 ай бұрын
I'm really stuck on a problem with the spindle setup, when ever i press the spindle orientation... The screen get disturbed and controller reboot, i would like ask for your support if i may, I'm from Morocco been on a company for 2 days no success
@recopakistan1520 3 ай бұрын
@crox2012 there is some issue in spindle drive
@crox2012 3 ай бұрын
@@recopakistan1520 the whole kit is brand new, indeed when i connect the i/o. Cable plug I hear a clicking noise for 3 second, is there a way to diagnose i/o on the servo drive ?
@allindiabest.rkshudha 3 ай бұрын
पार्ट अकाउंट कैसे इस मशीन में बढ़ेगा यह बताइए आप सर
@recopakistan1520 3 ай бұрын
Can you please wright in Roman Hindi or in English because I could not understand Hindi letters
@recopakistan1520 3 ай бұрын
I am replying after google translate you are asking for part count so answer is we cannot change part count but we can only do zero part count
@allindiabest.rkshudha 3 ай бұрын
@@recopakistan1520 ok sir thanks
@allindiabest.rkshudha 3 ай бұрын
Sir pat account kaise badhega is machine mein सर इस मशीन में प्रोडक्शन इन पार्ट नाम कैसे बढ़ायाजाएगा
@charles-hr7ir 3 ай бұрын
How good are ball screws and nuts for lifting
@recopakistan1520 3 ай бұрын
It is depending upon how much load you are lifting